Re: Problems with sending faxes

[Matthias.Apitz@SOFTCON.de (Matthias Apitz)]

Gregor Longariva wrote:
    
    Hello!
    
    I am currently using the newest distribution of Hylafax on
    a Linux 2.0.18 OS. receiving faxes works fine, but I have
    problems with sending faxes.
    I am using a NoName Faxmodem with a Rockwell 144DP
    Chip. The manufacture result of my modem is EXAR and the
    Version is 7.7 (whatever it means).
    
    When I try to send a fax, the modem dials. The other party
    responds with the fax answer carrier, but my fax doesn't
    recognize it.
    
    Any idea where's the problem?
    Thanx a lot!
    
    Gregor
    
    Here's a sample session log:
    
    Feb 18 19:26:37.55: [  204]: SESSION BEGIN 00000048 49913124
    Feb 18 19:26:37.56: [  204]: SEND FAX: JOB 9 DEST 24 COMMID 00000048
    Feb 18 19:26:37.56: [  204]: DELAY 2600 ms
    Feb 18 19:26:40.17: [  204]: <-- [15:ATE0V1Q0S0=0H0\r]
    Feb 18 19:26:40.77: [  204]: --> [14:ATE0V1Q0S0=0H0]
    Feb 18 19:26:40.77: [  204]: --> [2:OK]
    Feb 18 19:26:40.77: [  204]: <-- [21:ATS8=2S7=80&K3&D3&C1\r]
    Feb 18 19:26:41.01: [  204]: --> [2:OK]
    Feb 18 19:26:41.01: [  204]: <-- [12:AT+FCLASS=2\r]
    Feb 18 19:26:41.24: [  204]: --> [2:OK]
    Feb 18 19:26:41.24: [  204]: <-- [10:AT+FTBC=0\r]
    Feb 18 19:26:41.47: [  204]: --> [5:ERROR]
    Feb 18 19:26:41.47: [  204]: MODEM Command error
    Feb 18 19:26:41.47: [  204]: <-- [10:AT+FBOR=1\r]
    Feb 18 19:26:41.70: [  204]: --> [2:OK]
    Feb 18 19:26:41.70: [  204]: <-- [13:AT+FPHCTO=30\r]
    Feb 18 19:26:41.93: [  204]: --> [5:ERROR]
    Feb 18 19:26:41.93: [  204]: MODEM Command error
    Feb 18 19:26:41.93: [  204]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
    Feb 18 19:26:42.17: [  204]: --> [2:OK]
    Feb 18 19:26:42.17: [  204]: <-- [5:ATM0\r]
    Feb 18 19:26:42.40: [  204]: --> [2:OK]
    Feb 18 19:26:42.40: [  204]: <-- [12:AT+FCLASS=2\r]
    Feb 18 19:26:42.73: [  204]: --> [2:OK]
    Feb 18 19:26:42.73: [  204]: <-- [10:AT+FTBC=0\r]
    Feb 18 19:26:43.06: [  204]: --> [5:ERROR]
    Feb 18 19:26:43.06: [  204]: MODEM Command error
    Feb 18 19:26:43.06: [  204]: <-- [10:AT+FBOR=1\r]
    Feb 18 19:26:43.39: [  204]: --> [2:OK]
    Feb 18 19:26:43.39: [  204]: <-- [13:AT+FPHCTO=30\r]
    Feb 18 19:26:43.73: [  204]: --> [5:ERROR]
    Feb 18 19:26:43.73: [  204]: MODEM Command error
    Feb 18 19:26:43.73: [  204]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
    Feb 18 19:26:44.07: [  204]: --> [2:OK]
    Feb 18 19:26:44.07: [  204]: <-- [26:AT+FLID="+49 9131 604158"\r]
    Feb 18 19:26:44.41: [  204]: --> [2:OK]
    Feb 18 19:26:44.53: [  204]: DIAL 09135799845
    Feb 18 19:26:44.53: [  204]: <-- [8:ATDT09135799845@\r]
    Feb 18 19:28:07.91: [  204]: --> [9:NO ANSWER]
    Feb 18 19:28:08.95: [  204]: SEND FAILED: No answer from remote
    Feb 18 19:28:08.95: [  204]: <-- [5:ATH0\r]
    Feb 18 19:28:09.65: [  204]: --> [2:OK]
    Feb 18 19:28:09.78: [  204]: SESSION END

Try using this modem without the "@" symbol in the ModemDialCmd:
see config(4F) and Q81 of the FAQ for more information about this
problem;

	matthias