Re: [hylafax-users] i536ep issues (continuation)

[Bojan Stojanovic <bojan.stojanovic@xxxxxxxxxxxxx>]

And yes I have analogue line.

On Fri, 2006-06-02 at 15:32 +0200, Bojan Stojanovic wrote:
> We're gone offtopic so I changed name of a subject,
> 
> Minicom output:
> OK
> 
> RING - dialed from internal ext.
> AT+CGI=381
> ERROR
> AT+CGI=<381>
> ERROR
> 
> When dialed from external number minicom is always quiet.
> 
> What we have here is PBX which is authorative for +381112040xxx domain.
> HylaFAX here is etx. 962 (+381112040962). Ring patterns for calls which
> come from the outside world and from the internal ext. xxx are
> different. When I dial 962 (hylafax) from 936 (my ext.) that is a one
> long beep on ext. device (and minicom says RING), but when I call 962
> from let's say +38163306578 that are the 2 short beeps for ext. device
> (and minicom is quiet). That is the way PBX is set and it can't be
> changed. But when I use any external serial modem it recognies and
> minicom says RING for any type of call, from internal or external.
> 
> Fact is that with i536ep modem I can receive faxes sent only from
> company. B)
> 
> 536ep is good. some SmartLink internal PCI SW modems could only dial
> out, they were quiet in minicom from either internal or external call.
> 
> On Fri, 2006-06-02 at 14:41 +0200, Philippe Vouters wrote:
> > Bojan,
> > 
> > Looking at your AT commands, it seems you miss the AT+CGI=<your country
> > code>. I do not know if this can also help you, but people from Serbia
> > had to ATX3 to dial their respective ISP.
> > 
> > I can't say why there is no RING indicator when dialing though the PBX.
> > Are you sure you have an analog line (ATDT) and not a pulse line (ADTP)
> > when dialing through the PBX ? As the Intel 536EP is equipped with a
> > integrated buzzer, when dialing the 536EP modem number, do you hear
> > rings, some noise or absolutely nothing ?
> > 
> > Does it happen that if you remove /dev/536ep from the list of hylafax
> > recognized modems and you use "$ efax -v ewinchmart", does efax
> > indicates that a RING is detected ? Test it when dialing from locally
> > and from remotely to ensure you actually go through the PBX equipment.
> > 
> > Hoping this can help you.
> > Regards,
> > Philippe Vouters (Fontainebleau/France)
> > 
> > Le vendredi 02 juin 2006 à 10:28 +0200, Bojan Stojanovic a écrit :
> > > It works thanks to Philippe Vouters who modified Intel's driver so it
> > > now compiles under FC4, FC5, etc.
> > > http://linmodems.technion.ac.il/packages/Intel/Philippe.Vouters
> > > 
> > > Only thing is that I "can't" receive faxes as I described before:
> > > >"When I do a little testing in minicom, when I'm dialing Hylafax (from
> > > >960 to 962 for example)from internal line it says RING, but when I try
> > > >the same from any external line to Hylafax (2040962) minicom says
> > > >nothing."
> > > Ring pattern is different for external calls and our PBX admin can't do
> > > anything about it. External serial modems recognise this ring pattern
> > > fine but not 536ep.
> > > 
> > > Here is it's configuration (config.536ep):
> > > 
> > > CountryCode:            381
> > > AreaCode:               11
> > > FAXNumber:              +xxx.xx.xxxx.962
> > > LongDistancePrefix:     0
> > > InternationalPrefix:    99
> > > DialStringRules:        etc/dialrules
> > > ServerTracing:          1
> > > SessionTracing:         11
> > > RecvFileMode:           0600
> > > LogFileMode:            0600
> > > DeviceMode:             0600
> > > RingsBeforeAnswer:      0
> > > SpeakerVolume:          off
> > > GettyArgs:              "-h %l dx_%s"
> > > LocalIdentifier:        "Network Co."
> > > TagLineFont:            etc/lutRS18.pcf
> > > TagLineFormat:          "%%l|%c|Page %%P of %%T"
> > > PercentGoodLines:       0
> > > MaxConsecutiveBadLines: 100
> > > MaxRecvPages:           25
> > > ModemType:              Class1
> > > ModemDialCmd:           ATDT0%s
> > > Class1Cmd:              AT+FCLASS=1
> > > Class1PPMWaitCmd:       AT+FTS=7
> > > Class1TCFWaitCmd:       AT+FTS=7
> > > Class1EOPWaitCmd:       AT+FTS=9
> > > Class1SwitchingCmd:     AT+FRS=7
> > > Class1TrainingRecovery: 1500
> > > Class1RecvAbortOK:      200
> > > Class1FrameOverhead:    4
> > > Class1RecvIdentTimer:   40000
> > > Class1TCFMaxNonZero:    10
> > > Class1TCFMinRun:        1000
> > > 
> > > I don't know 'bout receivers fax machine i picked their fax No. randomly
> > > by googling and sent them a Google's home page as FAX. Receiver was some
> > > mathematic universities's library from Novi Sad (BTW I reccomend to you
> > > Novi Sad's http://eng.exitfest.org as a good summer time fest'). :-) 
> > > 
> > > They received a fax from the 3'rd try:
> > > 
> > > Your facsimile job to 021455662 was completed successfully.
> > > 
> > >             Pages: 1
> > >          Receiver: 003812155662
> > >           Quality: Fine
> > >        Page Width: 0 (mm)
> > >       Page Length: 0 (mm)
> > >       Signal Rate: 9600 bit/s
> > >       Data Format: 2-D MMR
> > >  Remote Equipment: Panasonic 
> > >    Remote Station: PMF NOVI SAD 
> > >           Dialogs: 3 (exchanges with remote device)
> > >             Calls: 3 (total phone calls placed)
> > >    Submitted From: 10.1.1.10
> > >             JobID: 10
> > >           GroupID: 10
> > >            CommID: c000000011
> > > 
> > > Processing time was 0:55.
> > > 
> > > Log of this job is attached.
> > > 
> > > Best regards,
> > Philippe Vouters (Fontainebleau/France)
> > http://linmodems.technion.ac.il/packages/Intel/
> > 
> > 
-- 
Bojan Stojanović
Network Co. A.D.
sistem administrator
tel: +381 11 2040 936



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*