Re: [hylafax-users] CallerID USR Modem?

["Michael Stowe" <mstowe@xxxxxxxxxxxxx>]

I have to admit I *had* that problem, which went away when I got sick of
trying to get my USR modem to behave itself.  I got some generic thing
that has yet to give me a moment's trouble.

You might want to try Class 1.

> Hi..  I'm trying to get CallerID working on my Hylafax Server.  I have the
> following Config file for ttyS5.  The modem detects the ring, tries to
> connect then can't get the handshake.  The CID information is being
> transmitted to my log files from faxgetty however it's still not making
> that handshake..  Anyone have this problem?
>
> -- Keith
>
> # Configuration for using the Class 2.0 command interface
> # with a USR v.34 Courier or Sporster modem.
> #
> # RTS/CTS flow control is used default.
> #
> #
> CountryCode:            1
> AreaCode:               847
> FAXNumber:              +1.847.451.0458
> LongDistancePrefix:     1
> InternationalPrefix:    011
> DialStringRules:        etc/dialrules
> ServerTracing:          1
> SessionTracing:         11
> RecvFileMode:           0600
> LogFileMode:            0600
> DeviceMode:             0600
> RingsBeforeAnswer:      2
> SpeakerVolume:          high
> GettyArgs:              "-h %l dx_%s"
> LocalIdentifier:        "NothingSetup"
> TagLineFont:            etc/lutRS18.pcf
> TagLineFormat:          "From %%l|%c|Page %%P of %%T"
> PercentGoodLines:       0
> MaxConsecutiveBadLines: 0
> ModemGroup:             "any: ttyS[5]"
> ModemClass:             "any: ttyS[5]"
> CIDNumber:              "NMBR ="
> CIDName:                "NAME ="
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType:              Class2.0        # use class 2.0 interface
> ModemRate:              19200           # DCE-DTE communication rate
> ModemFlowControl:       rtscts          # hardware flow control
> #
> ModemNoFlowCmd:         "AT&H0&I0&R1+VCID=1"   # setup modem for no flow
> control
> ModemHardFlowCmd:       "AT&H1&I0&R2+VCID=1"   # setup modem for hardware
> flow control
> ModemSoftFlowCmd:       "AT&H2&I2&R1+VCID=1"   # setup modem for software
> flow control
> #
> ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
> ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier
> (or not)
> ModemResultCodesCmd:    ATQ0X4          # enable extended result codes
> #ModemResetCmds:         "AT#CID=1"
> #
> # NB: adaptive answer only seems to work properly when
> #     the modem is left idling in Class 2.0
> #
> ModemSetupAACmd:        AT+FAA=1
> #
> # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
> # Note that we both turn the speaker on/off and set volume.
> #
> ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
> #
> # Modem does not support HDLC frame tracing; we add this just
> # to eliminate spurious ERROR results that confuse the naive.
> #
> Class2BUGCmd:           AT+FBU=0
> #
> # The modem doesn't support copy quality checking, even though it
> # returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
> # response so that the server will do copy quality checking.
> #
> Class2CQQueryCmd:       !(0),(0)        # override modem response
> #
> # Disables the reporting of bad frames by the modem.  This
> # overcomes a firmware problem in the x2 and V90 Sportsters.
> # It is not necessary for the Courier modem.
> #
> Class2NRCmd:    AT+FNR=1,1,1,0
> #
> # USR modems violate Class 2.0 specs and do not send RTC itself
> #
> Class2SendRTC:  yes
> #
> # +FAP=? not supported on this modem, gives ERROR in ServerTracing
> #
> Class2APQueryCmd:       none
>
> Keith Hamilton
> IT Manager/Software Developer
> [847] 451-0451 x121
> khamilton@xxxxxxxxxxx
>
> NOTICE - This email and any attachment may contain confidential and
> privileged material intended for the addressee only.  If you are not the
> addressee, you are notified that no part of this email or any attachment
> may be disclosed, copied or distributed, and that any other action related
> to this email or attachment is strictly prohibited, and may be unlawful.
> If you have received this email in error, please notify the sender
> immediately by return email, and delete this message. Thank you.
>
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
>   To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
> /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
>
>


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*