Re: [hylafax-users] Unspecified Phase D error

To: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] Unspecified Phase D error
From: Pablo Alcubilla <pablo.alcubilla@xxxxxxxxxxxxx>
Date: Thu, 10 Jun 2004 13:19:00 +0200

Lee Howard wrote:

It was already done when that log was taken, also i didint mention before the version is HylaFAX (tm) Version 4.2.0beta1

/etc/hylafax# grep Class2ECMType * config.ttyds01:Class2ECMType: 2.0 # follows Class 2.0 spec, not Class 2 config.ttyds02:Class2ECMType: 2.0 # follows Class 2.0 spec, not Class 2 config.ttyds03:Class2ECMType: 2.0 # follows Class 2.0 spec, not Class 2 config.ttyds04:Class2ECMType: 2.0 # follows Class 2.0 spec, not Class 2

Can you please increase ServerTracing to 0xFFF in the modem config file, restart faxgetty for one of the ports, and then post the FaxGetty log entries from your server log (/var/log/messages, probably). This will tell us what's going on as far as this goes.

Thanks.

Lee.

Hello,

Here i post you what i think you asked for and something more, just in case, many thanks Lee. :)

Pablo Alcubilla

This is what i get in a session file from /var/spool/hylafax/log

Jun 10 13:07:11.71: [ 2473]: SESSION BEGIN 000008793 34916590850 Jun 10 13:07:11.71: [ 2473]: HylaFAX (tm) Version 4.2.0beta1 Jun 10 13:07:11.71: [ 2473]: <-- [4:ATA\r] Jun 10 13:07:23.85: [ 2473]: --> [5:+FCON] Jun 10 13:07:23.85: [ 2473]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyds01' Jun 10 13:07:23.85: [ 2473]: STATE CHANGE: ANSWERING -> RECEIVING Jun 10 13:07:23.85: [ 2473]: MODEM input buffering enabled Jun 10 13:07:23.85: [ 2473]: RECV FAX: begin Jun 10 13:07:23.85: [ 2473]: --> [26:+FTSI: XXXXXXXXX] Jun 10 13:07:23.85: [ 2473]: REMOTE TSI "XXXXXXXXX" Jun 10 13:07:23.85: [ 2473]: --> [22:+FDCS: 1,5,0,0,0,0,0,0] Jun 10 13:07:23.85: [ 2473]: REMOTE wants 14400 bit/s Jun 10 13:07:23.85: [ 2473]: REMOTE wants A4 page width (215 mm) Jun 10 13:07:23.85: [ 2473]: REMOTE wants A4 page length (297 mm) Jun 10 13:07:23.85: [ 2473]: REMOTE wants 7.7 line/mm Jun 10 13:07:23.85: [ 2473]: REMOTE wants 1-D MH Jun 10 13:07:23.85: [ 2473]: --> [2:OK] Jun 10 13:07:23.85: [ 2473]: <-- [7:AT+FDR\r] Jun 10 13:07:23.95: [ 2473]: --> [5:+FCFR] Jun 10 13:07:23.95: [ 2473]: --> [22:+FDCS: 1,5,0,0,0,0,0,0] Jun 10 13:07:23.95: [ 2473]: REMOTE wants 14400 bit/s Jun 10 13:07:23.95: [ 2473]: REMOTE wants A4 page width (215 mm) Jun 10 13:07:23.95: [ 2473]: REMOTE wants A4 page length (297 mm) Jun 10 13:07:23.95: [ 2473]: REMOTE wants 7.7 line/mm Jun 10 13:07:23.95: [ 2473]: REMOTE wants 1-D MH Jun 10 13:07:23.95: [ 2473]: --> [7:CONNECT] Jun 10 13:07:23.95: [ 2473]: RECV: begin page Jun 10 13:07:23.95: [ 2473]: RECV: send trigger 021 Jun 10 13:07:23.95: [ 2473]: <-- data [1] Jun 10 13:07:23.95: [ 2473]: Copy quality checking performed by host Jun 10 13:07:46.84: [ 2473]: RECV: 2155 total lines, 0 bad lines, 0 consecutive bad lines Jun 10 13:07:46.84: [ 2473]: --> [13:+FPTS: 1,2156] Jun 10 13:07:46.84: [ 2473]: --> [7:+FET: 0] Jun 10 13:07:46.84: [ 2473]: RECV recv MPS (more pages, same document) Jun 10 13:07:46.84: [ 2473]: --> [2:OK] Jun 10 13:07:46.84: [ 2473]: RECV send MCF (message confirmation) Jun 10 13:07:46.84: [ 2473]: RECV FAX (000008793): from XXXXXXXXX, page 1 in 0:23, A4, 7.7 line/mm, 1-D MH, 14400 bit/s Jun 10 13:07:46.84: [ 2473]: <-- [7:AT+FDR\r] Jun 10 13:07:46.94: [ 2473]: --> [7:CONNECT] Jun 10 13:07:46.94: [ 2473]: RECV: begin page Jun 10 13:07:46.94: [ 2473]: RECV: send trigger 021 Jun 10 13:07:46.94: [ 2473]: <-- data [1] Jun 10 13:07:46.94: [ 2473]: Copy quality checking performed by host Jun 10 13:08:09.66: [ 2473]: RECV: 0 total lines, 0 bad lines, 0 consecutive bad lines Jun 10 13:08:09.66: [ 2473]: --> [10:+FPTS: 2,0] Jun 10 13:08:09.66: [ 2473]: --> [7:+FET: 2] Jun 10 13:08:09.66: [ 2473]: RECV recv EOP (no more pages or documents) Jun 10 13:08:09.66: [ 2473]: --> [2:OK] Jun 10 13:08:09.66: [ 2473]: RECV send RTN (retrain negative) Jun 10 13:08:09.66: [ 2473]: <-- [10:AT+FPTS=2\r] Jun 10 13:08:09.76: [ 2473]: --> [2:OK] Jun 10 13:08:09.76: [ 2473]: <-- [7:AT+FDR\r] Jun 10 13:08:21.42: [ 2473]: --> [10:+FHNG: 100] Jun 10 13:08:21.42: [ 2473]: REMOTE HANGUP: Unspecified Phase D error (code 100) Jun 10 13:08:21.42: [ 2473]: RECV keeping unconfirmed page Jun 10 13:08:21.42: [ 2473]: RECV FAX (000008793): from XXXXXXXXX, page 2 in 0:35, A4, 7.7 line/mm, 1-D MH, 14400 bit/s Jun 10 13:08:21.42: [ 2473]: RECV FAX (000008793): recvq/fax000001833.tif from XXXXXXXXX, route to <unspecified>, 2 pages in 0:58 Jun 10 13:08:21.42: [ 2473]: RECV FAX: Unspecified Phase D error Jun 10 13:08:21.42: [ 2473]: RECV FAX (000008793): session with XXXXXXXXX terminated abnormally: Unspecified Phase D error Jun 10 13:08:21.42: [ 2473]: RECV FAX: /usr/local/bin/faxrcvd.XXXXXXXXX "recvq/fax000001833.tif" "ttyds01" "000008793" "Unspecified Phase D error" "914024115 DAD: 916590850" "914024115 DAD: 916590850" Jun 10 13:08:21.42: [ 2473]: RECV FAX: end Jun 10 13:08:21.42: [ 2473]: SESSION END -------------------------------------------------------------------------------- The full config file

--------------------------------------------------------------------------------
# $Id: eicon-2,v 1.2 2004/03/05 02:29:32 lhoward Exp $
#
# prototype config file for the Eicon Diva ISDN Modem
#

#
#
CountryCode:            34
AreaCode:               ""
FAXNumber:              "916590850"
LongDistancePrefix:     ""
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          "0xFFFFF"
SessionTracing:         "0xFFFFF"
RecvFileMode:           0666
LogFileMode:            0666
DeviceMode:             0666
RingsBeforeAnswer:      3
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "TESTING"
LogFacility:            local5
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
QualifyCID:             /etc/hylafax/cid
MaxRecvPages:           25

ModemType:              Class2
ModemRate:              57600   # on boards supporting V.34-fax,
ModemFlowControl:       rtscts
ModemNoFlowCmd:         AT&K0
ModemSoftFlowCmd:       AT&K4
ModemHardFlowCmd:       AT&K3

Class2APQueryCmd:       ""
Class2SPLCmd:           ""
Class2TBCCmd:           ""
Class2ECMType:          2.0     # follows Class 2.0 spec, not Class 2

Class2UseHex: yes

FaxRcvdCmd: "/usr/local/bin/faxrcvd.bitmailer"

RingExtended:           "RING "
CIDNumber:              "RING CID: "
CIDName:                "RING CID: "
ModemResetCmds:         AT&F#CID=5\V1S0=2+iQ=a1

Class2Cmd: AT+FCLASS=2 # command to enter class 2 Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct) Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv Class2CQCmd: "" # commands to enable copy quality proc. Class2AbortCmd: AT+FK # abort session command Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities Class2TBCCmd: AT+FTBC=0 # setup stream mode Class2CRCmd: AT+FCR=1 # enable capability to receive Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing Class2LIDCmd: AT+FLID # set local identifier command Class2DCCCmd: AT+FDCC # set modem capabilities command Class2DISCmd: AT+FDIS # set session parameters command Class2DDISCmd: "" # disable pre-dial DIS command hack Class2CIGCmd: AT+FCIG # set polling identifier command Class2PTSCmd: AT+FPTS # set post-page status command Class2SPLCmd: AT+FSPL # set polling indicator command # # If Class2RecvDataTrigger is not set, then it is set to DC1 # Class2RecvDataTrigger: "" # character sent to modem to start recv Class2XmitWaitForXON: yes # if true, wait for XON before send --------------------------------------------------------------------------------

And the setup communication log from the local5.* facility -------------------------------------------------------------------------------- Jun 10 07:07:43 mail1 FaxGetty[20334]: MODEM set baud rate: 57600 baud, input flow RTS/CTS, output flow RTS/CTS Jun 10 07:07:43 mail1 FaxGetty[20334]: DELAY 10 ms Jun 10 07:07:43 mail1 FaxGetty[20334]: MODEM flush i/o Jun 10 07:07:43 mail1 FaxGetty[20334]: <-- [4:ATZ\r] Jun 10 07:07:43 mail1 FaxGetty[20334]: --> [3:ATZ] Jun 10 07:07:43 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:43 mail1 FaxGetty[20334]: DELAY 3000 ms Jun 10 07:07:46 mail1 FaxGetty[20334]: MODEM flush i/o Jun 10 07:07:46 mail1 FaxGetty[20334]: <-- [24:AT&F#CID=5\V1S0=2+IQ=A1\r] Jun 10 07:07:46 mail1 FaxGetty[20334]: --> [23:AT&F#CID=5\V1S0=2+IQ=A1] Jun 10 07:07:46 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:46 mail1 FaxGetty[20334]: <-- [7:ATS0=0\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [6:ATS0=0] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [5:ATE0\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [4:ATE0] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [5:ATV1\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [5:ATQ0\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [7:ATS8=2\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [8:ATS7=60\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [6:AT&K3\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [12:AT+FCLASS=?\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [5:0,1,2] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: MODEM Supports "Data" Jun 10 07:07:47 mail1 FaxGetty[20334]: MODEM Supports "Class 1" Jun 10 07:07:47 mail1 FaxGetty[20334]: MODEM Supports "Class 2" Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [12:AT+FCLASS=2\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [9:AT+FMFR?\r] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [22:Eicon Technology Corp.] Jun 10 07:07:47 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:47 mail1 FaxGetty[20334]: MODEM: Mfr Eicon Technology Corp. Jun 10 07:07:47 mail1 FaxGetty[20334]: <-- [9:AT+FMDL?\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [20:DIVA Unix ISDN Modem] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [9:AT+FREV?\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [11:Version 1.0] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM: Model DIVA Unix ISDN Modem Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM: Revision Version 1.0 Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [10:AT+FDCC=?\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [35:(0-7),(0-D),(0-2),(0-2),0,(0-2),0,0] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 3.85 line/mm Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 7.7 line/mm Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 15.4 line/mm Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports R16 x 15.4 line/mm Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 2400 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 4800 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 7200 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 9600 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 12000 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 14400 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 16800 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 19200 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 21600 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 24000 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 26400 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 28800 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 31200 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 33600 bit/s Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports A4 page width (215 mm) Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports B4 page width (255 mm) Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports A3 page width (303 mm) Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports A4 page length (297 mm) Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports B4 page length (364 mm) Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports unlimited page length Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 1-D MH Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports no ECM Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports T.30 Annex A, 64-byte ECM Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports T.30 Annex A, 256-byte ECM Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports T.30 Annex C, half duplex ECM Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports 0 ms/scanline Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [9:AT+FCQ=?\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Supports no copy quality checking Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [10:AT+FSPL=?\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [5:ERROR] Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [12:AT+FCLASS=2\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [10:AT+FTBC=0\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [5:ERROR] Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Command error Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [10:AT+FBOR=0\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [13:AT+FPHCTO=30\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [5:ERROR] Jun 10 07:07:48 mail1 FaxGetty[20334]: MODEM Command error Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [10:AT+FBUG=1\r] Jun 10 07:07:48 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:48 mail1 FaxGetty[20334]: <-- [24:AT+FDCC=7,D,2,2,0,2,0,0\r] Jun 10 07:07:49 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:49 mail1 FaxGetty[20334]: MODEM EICON TECHNOLOGY CORP. DIVA Unix ISDN Modem/Version 1.0 Jun 10 07:07:49 mail1 FaxGetty[20334]: <-- [5:ATM0\r] Jun 10 07:07:49 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:49 mail1 FaxGetty[20334]: <-- [10:AT+FREL=1\r] Jun 10 07:07:49 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:49 mail1 FaxGetty[20334]: <-- [9:AT+FCR=1\r] Jun 10 07:07:49 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:49 mail1 FaxGetty[20334]: <-- [20:AT+FLID="DANOSA E1"\r] Jun 10 07:07:49 mail1 FaxGetty[20334]: --> [2:OK] Jun 10 07:07:49 mail1 FaxGetty[20334]: STATE CHANGE: ANSWERING -> RUNNING (timeout 30) Jun 10 07:07:49 mail1 FaxGetty[20334]: MODEM input buffering disabled --------------------------------------------------------------------------------

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] Unspecified Phase D error
  - From: Lee Howard

References:
- [hylafax-users] Unspecified Phase D error
  - From: Pablo Alcubilla
- Re: [hylafax-users] Unspecified Phase D error
  - From: Lee Howard
- Re: [hylafax-users] Unspecified Phase D error
  - From: Pablo Alcubilla
- Re: [hylafax-users] Unspecified Phase D error
  - From: Lee Howard

Prev by Date: Re: [hylafax-users] winfax
Next by Date: [hylafax-users] confirm transmitted fax..
Previous by thread: Re: [hylafax-users] Unspecified Phase D error
Next by thread: Re: [hylafax-users] Unspecified Phase D error
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services