|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Class1 vs. Class2
Uh OK,
Then try this one.
I've changed the destination fax number for privacy reasons, but
otherwise it's the original log.
John
On Sat, Jan 04, 2003 at 07:05:03PM -0800, Lee Howard wrote:
Thanks, but these are the wrong logs. We need session logs, not server
logs. (/var/spool/hylafax/log/). Make sure SessionTracing (in your
config file) is 0xFFF. Don't bother sending Class 2 logs. We can't do
much about Class 2 firmware errors.
Lee.
--
PGP Public key ID: 1024D/2DE827B3
fingerprint = 8797 A26D 0854 2EAB 0285 A290 8A67 719C 2DE8 27B3
See http://www.keyserver.net or any PGP keyserver for public key.
Jan 03 13:17:06.28: [ 9115]: SESSION BEGIN 00000027 6185555555
Jan 03 13:17:06.28: [ 9115]: HylaFAX (tm) Version 4.1.1
Jan 03 13:17:06.28: [ 9115]: SEND FAX: JOB 4 DEST 5555555 COMMID 00000027 DEVICE '/dev/ttyS2'
Jan 03 13:17:06.28: [ 9115]: MODEM set DTR OFF
Jan 03 13:17:06.28: [ 9115]: DELAY 75 ms
Jan 03 13:17:06.36: [ 9115]: MODEM set DTR ON
Jan 03 13:17:06.36: [ 9115]: DELAY 2600 ms
Jan 03 13:17:08.96: [ 9115]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS
Jan 03 13:17:08.96: [ 9115]: MODEM flush i/o
Jan 03 13:17:08.96: [ 9115]: <-- [4:ATZ\r]
Jan 03 13:17:09.93: [ 9115]: --> [2:OK]
Jan 03 13:17:09.93: [ 9115]: DELAY 3000 ms
Jan 03 13:17:12.93: [ 9115]: <-- [5:ATE0\r]
Jan 03 13:17:13.06: [ 9115]: --> [4:ATE0]
Jan 03 13:17:13.06: [ 9115]: --> [2:OK]
Jan 03 13:17:13.06: [ 9115]: <-- [5:ATV1\r]
Jan 03 13:17:13.19: [ 9115]: --> [2:OK]
Jan 03 13:17:13.19: [ 9115]: <-- [5:ATQ0\r]
Jan 03 13:17:13.32: [ 9115]: --> [2:OK]
Jan 03 13:17:13.32: [ 9115]: <-- [7:ATS0=0\r]
Jan 03 13:17:13.45: [ 9115]: --> [2:OK]
Jan 03 13:17:13.45: [ 9115]: <-- [7:ATS8=2\r]
Jan 03 13:17:13.58: [ 9115]: --> [2:OK]
Jan 03 13:17:13.58: [ 9115]: <-- [8:ATS7=60\r]
Jan 03 13:17:13.71: [ 9115]: --> [2:OK]
Jan 03 13:17:13.71: [ 9115]: <-- [6:AT&K3\r]
Jan 03 13:17:13.84: [ 9115]: --> [2:OK]
Jan 03 13:17:13.84: [ 9115]: <-- [6:AT&D2\r]
Jan 03 13:17:13.97: [ 9115]: --> [2:OK]
Jan 03 13:17:13.97: [ 9115]: <-- [6:AT&C1\r]
Jan 03 13:17:14.10: [ 9115]: --> [2:OK]
Jan 03 13:17:14.10: [ 9115]: <-- [12:AT+FCLASS=1\r]
Jan 03 13:17:14.23: [ 9115]: --> [2:OK]
Jan 03 13:17:14.23: [ 9115]: <-- [5:ATM0\r]
Jan 03 13:17:14.26: [ 9115]: --> [2:OK]
Jan 03 13:17:14.26: [ 9115]: STATE CHANGE: RUNNING -> SENDING
Jan 03 13:17:14.26: [ 9115]: MODEM input buffering enabled
Jan 03 13:17:14.26: [ 9115]: <-- [12:AT+FCLASS=1\r]
Jan 03 13:17:14.39: [ 9115]: --> [2:OK]
Jan 03 13:17:14.39: [ 9115]: DIAL 5555555
Jan 03 13:17:14.39: [ 9115]: <-- [13:ATDT5555555\r]
Jan 03 13:17:23.57: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:23.57: [ 9115]: MODEM input buffering disabled
Jan 03 13:17:25.34: [ 9115]: --> HDLC<45:FF C0 04 00 00 9E 00 00 00 69 FE 90 C8 00 08 00 48 A1 03 0B 1F 01 A2 80 92 40 0C 0C 6C 8C 1C 04 9C 2C 4C 9C 04 AC 1C 4C 9C 04 C0 F0 0C>
Jan 03 13:17:25.36: [ 9115]: --> [2:OK]
Jan 03 13:17:25.36: [ 9115]: REMOTE NSF "00 00 79 00 00 00 96 7F 09 13 00 10 00 12 85 C0 D0 F8 80 45 01 49 02 30 30 36 31 38 20 39 34 32 39 20 35 38 32 39 20 03 0F"
Jan 03 13:17:25.36: [ 9115]: NSF remote fax equipment: Panasonic
Jan 03 13:17:25.36: [ 9115]: NSF remote station ID: "00618 9555 5555 "
Jan 03 13:17:25.36: [ 9115]: <-- [9:AT+FRH=3\r]
Jan 03 13:17:25.39: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:25.72: [ 9115]: --> HDLC<12:FF C8 01 04 77 1F 23 01 09 C0 28 4B>
Jan 03 13:17:25.74: [ 9115]: --> [2:OK]
Jan 03 13:17:25.74: [ 9115]: REMOTE best rate 14400 bit/s
Jan 03 13:17:25.74: [ 9115]: REMOTE max page width 1728 pixels in 215 mm
Jan 03 13:17:25.74: [ 9115]: REMOTE max unlimited page length
Jan 03 13:17:25.74: [ 9115]: REMOTE best vres 7.7 line/mm
Jan 03 13:17:25.74: [ 9115]: REMOTE best format 2-D MMR
Jan 03 13:17:25.74: [ 9115]: REMOTE supports T.30 Annex A, ECM
Jan 03 13:17:25.74: [ 9115]: REMOTE best 0 ms/scanline
Jan 03 13:17:25.74: [ 9115]: USE 14400 bit/s
Jan 03 13:17:25.74: [ 9115]: USE 0 ms/scanline
Jan 03 13:17:25.74: [ 9115]: SEND file "docq/doc4.cover;40"
Jan 03 13:17:25.74: [ 9115]: USE page width 1728 pixels in 215 mm
Jan 03 13:17:25.74: [ 9115]: USE unlimited page length
Jan 03 13:17:25.74: [ 9115]: USE 3.85 line/mm
Jan 03 13:17:25.74: [ 9115]: USE 2-D MR
Jan 03 13:17:25.74: [ 9115]: SEND training at v.17 14400 bit/s
Jan 03 13:17:25.74: [ 9115]: <-- [9:AT+FTH=3\r]
Jan 03 13:17:25.80: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:25.80: [ 9115]: <-- HDLC<23:FF C0 C2 B6 4E F6 66 36 36 A6 C2 04 04 04 04 04 04 04 04 04 04 04 04>
Jan 03 13:17:25.80: [ 9115]: <-- data [23]
Jan 03 13:17:25.80: [ 9115]: <-- data [2]
Jan 03 13:17:27.58: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:27.58: [ 9115]: <-- HDLC<6:FF C8 C1 00 45 1E>
Jan 03 13:17:27.58: [ 9115]: <-- data [6]
Jan 03 13:17:27.58: [ 9115]: <-- data [2]
Jan 03 13:17:28.03: [ 9115]: --> [2:OK]
Jan 03 13:17:28.03: [ 9115]: <-- [9:AT+FTS=7\r]
Jan 03 13:17:28.14: [ 9115]: --> [2:OK]
Jan 03 13:17:28.14: [ 9115]: <-- [11:AT+FTM=145\r]
Jan 03 13:17:28.19: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:28.19: [ 9115]: <-- data [1024]
Jan 03 13:17:28.19: [ 9115]: <-- data [1024]
Jan 03 13:17:28.19: [ 9115]: <-- data [652]
Jan 03 13:17:28.19: [ 9115]: <-- data [2]
Jan 03 13:17:31.31: [ 9115]: --> [2:OK]
Jan 03 13:17:31.31: [ 9115]: <-- [9:AT+FRH=3\r]
Jan 03 13:17:32.13: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:32.96: [ 9115]: --> HDLC<5:FF C8 21 57 BE>
Jan 03 13:17:32.98: [ 9115]: --> [2:OK]
Jan 03 13:17:32.98: [ 9115]: TRAINING succeeded
Jan 03 13:17:32.98: [ 9115]: DELAY 75 ms
Jan 03 13:17:33.06: [ 9115]: <-- [11:AT+FTM=146\r]
Jan 03 13:17:33.11: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:33.11: [ 9115]: SEND begin page
Jan 03 13:17:33.11: [ 9115]: <-- data [1045]
Jan 03 13:17:33.11: [ 9115]: <-- data [1035]
Jan 03 13:17:33.11: [ 9115]: <-- data [1027]
Jan 03 13:17:33.11: [ 9115]: <-- data [1034]
Jan 03 13:17:35.51: [ 9115]: <-- data [1029]
Jan 03 13:17:35.51: [ 9115]: <-- data [915]
Jan 03 13:17:35.51: [ 9115]: SENT 6027 bytes of data
Jan 03 13:17:35.51: [ 9115]: SEND 2D RTC
Jan 03 13:17:35.51: [ 9115]: <-- data [30]
Jan 03 13:17:35.51: [ 9115]: <-- data [2]
Jan 03 13:17:35.51: [ 9115]: SEND end page
Jan 03 13:17:35.80: [ 9115]: --> [2:OK]
Jan 03 13:17:35.80: [ 9115]: <-- [9:AT+FTS=7\r]
Jan 03 13:17:37.08: [ 9115]: --> [2:OK]
Jan 03 13:17:37.08: [ 9115]: SEND send MPS (more pages, same document)
Jan 03 13:17:37.08: [ 9115]: <-- [9:AT+FTH=3\r]
Jan 03 13:17:37.15: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:37.15: [ 9115]: <-- HDLC<3:FF C8 F2>
Jan 03 13:17:37.15: [ 9115]: <-- data [3]
Jan 03 13:17:37.15: [ 9115]: <-- data [2]
Jan 03 13:17:38.45: [ 9115]: --> [2:OK]
Jan 03 13:17:38.45: [ 9115]: <-- [9:AT+FRH=3\r]
Jan 03 13:17:41.55: [ 9115]: --> [0:]
Jan 03 13:17:41.55: [ 9115]: MODEM <Empty line>
Jan 03 13:17:41.55: [ 9115]: MODEM TIMEOUT: waiting for v.21 carrier
Jan 03 13:17:41.55: [ 9115]: <-- data [1]
Jan 03 13:17:41.62: [ 9115]: --> [2:OK]
Jan 03 13:17:41.62: [ 9115]: SEND send MPS (more pages, same document)
Jan 03 13:17:41.62: [ 9115]: <-- [9:AT+FTH=3\r]
Jan 03 13:17:41.69: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:41.69: [ 9115]: <-- HDLC<3:FF C8 F2>
Jan 03 13:17:41.69: [ 9115]: <-- data [3]
Jan 03 13:17:41.69: [ 9115]: <-- data [2]
Jan 03 13:17:43.00: [ 9115]: --> [2:OK]
Jan 03 13:17:43.00: [ 9115]: <-- [9:AT+FRH=3\r]
Jan 03 13:17:46.10: [ 9115]: --> [0:]
Jan 03 13:17:46.10: [ 9115]: MODEM <Empty line>
Jan 03 13:17:46.10: [ 9115]: MODEM TIMEOUT: waiting for v.21 carrier
Jan 03 13:17:46.10: [ 9115]: <-- data [1]
Jan 03 13:17:46.18: [ 9115]: --> [2:OK]
Jan 03 13:17:46.18: [ 9115]: SEND send MPS (more pages, same document)
Jan 03 13:17:46.18: [ 9115]: <-- [9:AT+FTH=3\r]
Jan 03 13:17:46.24: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:46.24: [ 9115]: <-- HDLC<3:FF C8 F2>
Jan 03 13:17:46.24: [ 9115]: <-- data [3]
Jan 03 13:17:46.24: [ 9115]: <-- data [2]
Jan 03 13:17:47.55: [ 9115]: --> [2:OK]
Jan 03 13:17:47.55: [ 9115]: <-- [9:AT+FRH=3\r]
Jan 03 13:17:50.65: [ 9115]: --> [0:]
Jan 03 13:17:50.65: [ 9115]: MODEM <Empty line>
Jan 03 13:17:50.65: [ 9115]: MODEM TIMEOUT: waiting for v.21 carrier
Jan 03 13:17:50.65: [ 9115]: <-- data [1]
Jan 03 13:17:50.74: [ 9115]: --> [2:OK]
Jan 03 13:17:50.74: [ 9115]: No response to MPS or EOP repeated 3 tries
Jan 03 13:17:50.74: [ 9115]: <-- [9:AT+FTH=3\r]
Jan 03 13:17:50.80: [ 9115]: --> [7:CONNECT]
Jan 03 13:17:50.80: [ 9115]: <-- HDLC<3:FF C8 DF>
Jan 03 13:17:50.80: [ 9115]: <-- data [3]
Jan 03 13:17:50.80: [ 9115]: <-- data [2]
Jan 03 13:17:52.11: [ 9115]: --> [2:OK]
Jan 03 13:17:52.11: [ 9115]: MODEM input buffering enabled
Jan 03 13:17:52.11: [ 9115]: <-- [5:ATH0\r]
Jan 03 13:17:52.82: [ 9115]: --> [2:OK]
Jan 03 13:17:52.82: [ 9115]: MODEM set DTR OFF
Jan 03 13:17:52.82: [ 9115]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Jan 03 13:17:52.83: [ 9115]: SESSION END
PGP signature
