|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
"MODEM input buffering disabled"
using Linux (suse-linux), Hylafax v4.0, faxgetty
Hello,
I got help with my problem of the fine strokes, that my modem
faxes sometime in the middle of a faxsimile. My /var/log/messages
reads:
Nov 10 17:48:12 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:12 rex FaxSend[541]: MODEM TEXAS INSTRUMENTS INC. 56.0
VOICE /
Nov 10 17:48:12 rex FaxSend[541]: MODEM input buffering disabled
Nov 10 17:48:12 rex FaxSend[541]: SEND FAX: JOB 17 DEST 01013
02213494359 COMMID 00000112
Can somebody tell me where I can enable "Modem input buffering" ?
I have already commented in and out the config-lines in config.ttyS1
that appear to have something to to with flow control.
Thank you.
Ekkard
by the way: If I comment in ModemSoftFlowCmd there appears an error in
/var/log/messages:
Nov 17 11:13:18 rex FaxSend[758]: <-- [15:ATE0V1Q0S0=0H0\r]
Nov 17 11:13:18 rex FaxSend[758]: --> [2:OK]
Nov 17 11:13:18 rex FaxSend[758]: <-- [16:ATS8=2S7=150&K4\r]
Nov 17 11:13:19 rex FaxSend[758]: --> [5:ERROR]
Nov 17 11:13:19 rex FaxSend[758]: MODEM Command error
Nov 17 11:13:19 rex FaxSend[758]: MODEM set DTR OFF
===============================================================
Here is my complete config.ttyS1 :
# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 49
AreaCode: 721
FAXNumber: +49.721.859519
LongDistancePrefix: 0
InternationalPrefix: 0049
DialStringRules: etc/dialrules
ServerTracing: 527
SessionTracing: 527
RecvFileMode: 0644
LogFileMode: 0600
DeviceMode: 0666
RingsBeforeAnswer: 5
SpeakerVolume: high
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "Ekkard Gerlach"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%p of %%t"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2.0 # use this to supply a hint
#ModemRate: 19200 # max rate for DCE-DTE communication
ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
# ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" Original, Ekkard
ModemSetVolumeCmd: ATM2L3
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
ModemWaitTimeCmd: ATS7=150 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct)
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
#Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control command
=================================================
Here is /var/log/messages with the errors:
Nov 10 17:48:07 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:07 rex FaxSend[541]: <-- [13:ATS8=2S7=150\r]
Nov 10 17:48:07 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:07 rex FaxSend[541]: <-- [12:AT+FCLASS=?\r]
Nov 10 17:48:07 rex FaxSend[541]: --> [7:0,1,2.0]
Nov 10 17:48:07 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:07 rex FaxSend[541]: <-- [14:AT+FCLASS=2.0\r]
Nov 10 17:48:08 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:08 rex FaxSend[541]: <-- [8:AT+FMI?\r]
Nov 10 17:48:08 rex FaxSend[541]: --> [33:Texas Instruments Inc. 56.0
Voice]
Nov 10 17:48:08 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:08 rex FaxSend[541]: <-- [8:AT+FMM?\r]
Nov 10 17:48:08 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:08 rex FaxSend[541]: <-- [8:AT+FMR?\r]
Nov 10 17:48:09 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:09 rex FaxSend[541]: <-- [9:AT+FCC=?\r]
Nov 10 17:48:09 rex FaxSend[541]: -->
[35:(0,1),(0-5),(0-2),(0-2),0,0,0,(0-7)]
Nov 10 17:48:09 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:09 rex FaxSend[541]: <-- [9:AT+FCQ=?\r]
Nov 10 17:48:09 rex FaxSend[541]: --> [11:(0-2),(0-2)]
Nov 10 17:48:10 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:10 rex FaxSend[541]: <-- [9:AT+FAP=?\r]
Nov 10 17:48:10 rex FaxSend[541]: --> [5:ERROR]
Nov 10 17:48:10 rex FaxSend[541]: <-- [9:AT+FSP=?\r]
Nov 10 17:48:10 rex FaxSend[541]: --> [5:(0,1)]
Nov 10 17:48:10 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:10 rex FaxSend[541]: <-- [14:AT+FCLASS=2.0\r]
Nov 10 17:48:10 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:10 rex FaxSend[541]: <-- [9:AT+FLO=0\r]
Nov 10 17:48:11 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:11 rex FaxSend[541]: <-- [9:AT+FPP=0\r]
Nov 10 17:48:11 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:11 rex FaxSend[541]: <-- [9:AT+FBO=0\r]
Nov 10 17:48:11 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:11 rex FaxSend[541]: <-- [10:AT+FCT=30\r]
Nov 10 17:48:11 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:11 rex FaxSend[541]: <-- [15:AT+FNR=1,1,1,1\r]
Nov 10 17:48:12 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:12 rex FaxSend[541]: <-- [9:AT+FIE=0\r]
Nov 10 17:48:12 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:12 rex FaxSend[541]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Nov 10 17:48:12 rex FaxSend[541]: --> [2:OK]
Nov 10 17:48:12 rex FaxSend[541]: MODEM TEXAS INSTRUMENTS INC. 56.0
VOICE /
Nov 10 17:48:12 rex FaxSend[541]: MODEM input buffering disabled
Nov 10 17:48:12 rex FaxSend[541]: SEND FAX: JOB 17 DEST 01013 0221
3494359 COMMID 00000112
Nov 10 17:49:28 rex FaxQueuer[187]: JOB 17 (active dest
+49101302213494359 pri 126 tts 0:00 killtime
2:53:30): CMD DONE: exit status 0x200
Nov 10 17:49:28 rex FaxQueuer[187]: JOB 17 (done dest +49101302213494359
pri 126 tts 0:00 killtime 2
:53:30): SEND DONE: 1:24
Nov 10 17:49:37 rex FaxGetty[425]: MODEM set DTR OFF
Nov 10 17:49:37 rex FaxGetty[425]: DELAY 2600 ms
Nov 10 17:49:39 rex FaxGetty[425]: MODEM set DTR ON
Nov 10 17:49:39 rex FaxGetty[425]: MODEM set baud rate: 19200 baud,
input flow NONE, output flow NON
E
Nov 10 17:49:39 rex FaxGetty[425]: MODEM flush i/o
Nov 10 17:49:39 rex FaxGetty[425]: <-- [15:ATE0V1Q0S0=0H0\r]
Nov 10 17:49:39 rex FaxGetty[425]: --> [2:OK]
Nov 10 17:49:39 rex FaxGetty[425]: <-- [13:ATS8=2S7=150\r]
Nov 10 17:49:40 rex FaxGetty[425]: --> [2:OK]
