Re: [hylafax-users] caller ID issue

["Ivan Petrov" <ivanp@xxxxxxxxxxxxx>]

Thanks Lee,

I just tried Class 1 - now I can receive the fax, but seems I don't get the 
callerID at all.
This is the config file I'm trying.

CountryCode:            1
AreaCode:               416
FAXNumber:              +1.416.xxx.xxxx
LongDistancePrefix:     1InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      2
SpeakerVolume:          yes
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        FAX
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
ModemResetCmds:         AT#CID=1

# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use class 1 interface
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # hardware flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or 
not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow 
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow 
control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd:       ATI7            # XXX, returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow 
control
Class1SFLOCmd:          ""              # modem does this automatically
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:        AT+FCLASS=0&H1&I0&R2    # leave modem in class 0
ModemAnswerCmd:         AT+FCLASS=1&H1&I0&R2A   # force RTS/CTS after change
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0


Regards,
Ivan

----- Original Message ----- 
From: "Lee Howard" <faxguy@xxxxxxxxxxxxxxxx>
To: "Ivan Petrov" <ivanp@xxxxxxxxxxxxx>
Cc: <hylafax-users@xxxxxxxxxxx>
Sent: Thursday, December 15, 2005 2:31 PM
Subject: Re: [hylafax-users] caller ID issue


> Try switching to Class 1.
>
> Lee.
>
>
> Ivan Petrov wrote:
>
> > Hi,
> >  I am using hylafax 4.2.3 on RHEL 3 (updater 6) with a US Robotics 
> > Sportster 56K modem. My line has caller ID option. I am having problems 
> > receiving faxes if I enable caller ID in modem config file. Here is what 
> > I add to the modem config file (I also switched to answer on 2 ring so I 
> > can get the caller ID info):
> >  ModemResetCmds:         AT#CID=1
> >  When enabled - here is what happens: in hylafax log file I get:
> >  Dec 15 13:25:50.50: [ 4553]: SESSION BEGIN 000000053 14166075301
> > Dec 15 13:25:50.50: [ 4553]: HylaFAX (tm) Version 4.2.3
> > Dec 15 13:25:50.50: [ 4553]: CallID: "4165555555" "COMPANYNAME"
> > Dec 15 13:25:50.50: [ 4553]: <-- [4:ATA\r]
> > Dec 15 13:26:38.57: [ 4553]: --> [4:+FCO]
> > Dec 15 13:26:38.57: [ 4553]: ANSWER: FAX CONNECTION  DEVICE '/dev/modem'
> > Dec 15 13:26:38.57: [ 4553]: RECV FAX: begin
> > Dec 15 13:26:41.00: [ 4553]: --> [7:+FHS:74]
> > Dec 15 13:26:41.00: [ 4553]: REMOTE HANGUP: T.30 T1 timeout after EOM 
> > received (code 74)
> > Dec 15 13:26:41.01: [ 4553]: --> [2:OK]
> > Dec 15 13:26:41.01: [ 4553]: RECV FAX: T.30 T1 timeout after EOM received
> > Dec 15 13:26:41.01: [ 4553]: RECV FAX: end
> > Dec 15 13:26:41.01: [ 4553]: SESSION END
> >  What happens is sending party closes the call. I tried with couple of 
> > different fax machines - result always the same.
> >  If I only change
> >  ModemResetCmds:         AT#CID=0
> >  (disable callerID) I can receive fax without problems.
> >  Anyone have an idea what could be wrong?
> >
> > Thank you!
> >  Ivan


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*