Re: [hylafax-users] High failure rate on sending

To: Daniel Hillhouse <daniel.hillhouse@xxxxxxxxxxxxxxxx>
Subject: Re: [hylafax-users] High failure rate on sending
From: Lee Howard <faxguy@xxxxxxxxxxxxxxxx>
Cc: hylafax-users@xxxxxxxxxxx
Date: Fri, 04 Nov 2005 06:53:58 -0800

Daniel,

At this point I would start to consider the modem hardware/firmware suspect.

There may be some kind of initialization that would work around the problem, but that may require you to contact and work with the manufacturer.

Thanks,

Lee.

Daniel Hillhouse wrote:

Thanks Lee.

I was using xonxoff so I changed that to rtscts but it still had errors. This time it didn't resubmit those sections. Here is the bottom of the new log. Everything went fine up to frame 255.

... Nov 04 15:46:04.22: [ 9837]: SEND send frame number 255 Nov 04 15:46:04.22: [ 9837]: DELAY 200 ms Nov 04 15:46:04.41: [ 9837]: <-- [11:AT+FTM=146\r] Nov 04 15:46:04.91: [ 9837]: --> [7:CONNECT] Nov 04 15:46:43.30: [ 9837]: --> [2:OK] Nov 04 15:46:43.30: [ 9837]: <-- [9:AT+FTS=9\r] Nov 04 15:46:43.32: [ 9837]: --> [2:OK] Nov 04 15:46:43.32: [ 9837]: <-- [9:AT+FTH=3\r] Nov 04 15:46:43.37: [ 9837]: --> [7:CONNECT] Nov 04 15:46:44.79: [ 9837]: --> [2:OK] Nov 04 15:46:44.79: [ 9837]: SEND send PPS (partial page signal) Nov 04 15:46:44.79: [ 9837]: SEND send NULL (more blocks, same page) Nov 04 15:46:44.79: [ 9837]: <-- [9:AT+FRH=3\r] Nov 04 15:46:45.47: [ 9837]: --> [7:CONNECT] Nov 04 15:46:49.72: [ 9837]: --> [2:OK] Nov 04 15:46:49.72: [ 9837]: HDLC frame too short (0 bytes) Nov 04 15:46:49.72: [ 9837]: <-- [9:AT+FRS=7\r] Nov 04 15:46:49.74: [ 9837]: --> [2:OK] Nov 04 15:46:49.74: [ 9837]: <-- [9:AT+FTH=3\r] Nov 04 15:46:49.79: [ 9837]: --> [7:CONNECT] Nov 04 15:46:51.11: [ 9837]: --> [2:OK] Nov 04 15:46:51.11: [ 9837]: SEND send CRP (command repeat) Nov 04 15:46:51.11: [ 9837]: <-- [9:AT+FRH=3\r] Nov 04 15:46:54.21: [ 9837]: --> [0:] Nov 04 15:46:54.21: [ 9837]: MODEM <Empty line> Nov 04 15:46:54.41: [ 9837]: MODEM <Timeout> Nov 04 15:46:54.41: [ 9837]: <-- [9:AT+FTH=3\r] Nov 04 15:46:54.46: [ 9837]: --> [7:CONNECT] Nov 04 15:46:55.88: [ 9837]: --> [2:OK] Nov 04 15:46:55.88: [ 9837]: SEND send PPS (partial page signal) Nov 04 15:46:55.88: [ 9837]: SEND send NULL (more blocks, same page) Nov 04 15:46:55.88: [ 9837]: <-- [9:AT+FRH=3\r] Nov 04 15:46:56.54: [ 9837]: --> [7:CONNECT] Nov 04 15:47:00.82: [ 9837]: --> [2:OK] Nov 04 15:47:00.82: [ 9837]: HDLC frame too short (0 bytes) Nov 04 15:47:00.82: [ 9837]: <-- [9:AT+FRS=7\r] Nov 04 15:47:00.84: [ 9837]: --> [2:OK] Nov 04 15:47:00.84: [ 9837]: <-- [9:AT+FTH=3\r] Nov 04 15:47:00.89: [ 9837]: --> [7:CONNECT] Nov 04 15:47:02.21: [ 9837]: --> [2:OK] Nov 04 15:47:02.21: [ 9837]: SEND send CRP (command repeat) Nov 04 15:47:02.21: [ 9837]: <-- [9:AT+FRH=3\r] Nov 04 15:47:05.31: [ 9837]: --> [0:] Nov 04 15:47:05.31: [ 9837]: MODEM <Empty line> Nov 04 15:47:05.51: [ 9837]: MODEM <Timeout> Nov 04 15:47:05.51: [ 9837]: <-- [9:AT+FTH=3\r] Nov 04 15:47:05.56: [ 9837]: --> [7:CONNECT] Nov 04 15:47:06.98: [ 9837]: --> [2:OK] Nov 04 15:47:06.98: [ 9837]: SEND send PPS (partial page signal) Nov 04 15:47:06.98: [ 9837]: SEND send NULL (more blocks, same page) Nov 04 15:47:06.98: [ 9837]: <-- [9:AT+FRH=3\r] Nov 04 15:47:07.66: [ 9837]: --> [7:CONNECT] Nov 04 15:47:09.73: [ 9837]: --> [2:OK] Nov 04 15:47:09.73: [ 9837]: HDLC frame with bad control field 0x20 Nov 04 15:47:09.73: [ 9837]: <-- [9:AT+FRS=7\r] Nov 04 15:47:09.75: [ 9837]: --> [2:OK] Nov 04 15:47:09.75: [ 9837]: <-- [9:AT+FTH=3\r] Nov 04 15:47:09.80: [ 9837]: --> [7:CONNECT] Nov 04 15:47:11.11: [ 9837]: --> [2:OK] Nov 04 15:47:11.11: [ 9837]: SEND send CRP (command repeat) Nov 04 15:47:11.11: [ 9837]: <-- [9:AT+FRH=3\r] Nov 04 15:47:14.21: [ 9837]: --> [0:] Nov 04 15:47:14.21: [ 9837]: MODEM <Empty line> Nov 04 15:47:14.41: [ 9837]: MODEM <Timeout> Nov 04 15:47:14.41: [ 9837]: No response to PPS repeated 3 times. Nov 04 15:47:14.41: [ 9837]: SEND end page Nov 04 15:47:14.41: [ 9837]: <-- [9:AT+FTH=3\r] Nov 04 15:47:14.46: [ 9837]: --> [7:CONNECT] Nov 04 15:47:15.78: [ 9837]: --> [2:OK] Nov 04 15:47:15.78: [ 9837]: SEND FAILED: JOB 367

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] High failure rate on sending
  - From: Daniel Hillhouse

References:
- [hylafax-users] High failure rate on sending
  - From: Daniel Hillhouse
- Re: [hylafax-users] High failure rate on sending
  - From: Lee Howard
- Re: [hylafax-users] High failure rate on sending
  - From: Daniel Hillhouse

Prev by Date: [hylafax-users] Digital Fax board + SIP VOIP Support
Next by Date: Re: [hylafax-users] T.30 T2 timeout, expected signal not received
Previous by thread: Re: [hylafax-users] High failure rate on sending
Next by thread: Re: [hylafax-users] High failure rate on sending
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services