|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] 4.2.2 & Mainpine not working
guys,
I am having problem with running either faxsetup or
faxaddmodem for more than two port. I have a Oct+
8 port MainPine. It only allow me to do a complete set
up and detecting for only two ports (port ttyS4 and ttyS11)
I am running hylafax 4.2.2 and RedHat ES 3.0. Please see
the complain at the end of this email: Unable to deduce DTE-
DCE speed; Any sugguestion?
CountryCode: 1
AreaCode: 587
FAXNumber: +1.567.777.7777
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
SessionTracing: 11
RingsBeforeAnswer: 1
SpeakerVolume: high
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
Are these ok [yes]?
Now we are going to probe the tty port to figure out the type
of modem that is attached. This takes a few seconds, so be
patient.
Note that if you do not have the modem cabled to the port, or
the
modem is turned off, this may hang (just go and cable up the
modem
or turn it on, or whatever).
Probing for best speed to talk to modem:
Unable to deduce DTE-DCE speed; check that you are using the
correct device and/or that your modem is setup properly. If
all else fails, try the -s option to lock the speed.
---- Original message ----
>Date: Thu, 13 Oct 2005 11:36:07 -0400
>From: Tom Miller <tom@xxxxxxxxxxxxxx>
>Subject: 4.2.2 & Mainpine not working
>To: support@xxxxxxxxxxxx, hylafax-users@xxxxxxxxxxx
>
>Does anyone have the same problem with version 4.2.2 and
>Mainpine modem?
>
>I reinstall Hylafax 4.2.2 and went through the same faxsetup
>as before for version 4.2.1 except one thing I used class =
>1.0 instead of 1. The hylafax and modem doesn't pickup and
>accept any incoming fax at all. I have 8 port MainPine
Oct+ .
> However, after ran the faxsetup modem only port ttyS4 and
>ttyS11 were created the rest was not and have the following
error:
>
>Probing for best speed to talk to modem:
>Unable to deduce DTE-DCE speed; check that you are using the
>correct device and/or that your modem is setup properly. If
>all else fails, try the -s option to lock the speed.
>
>What happen to faxstat? It is different in 4.2.2
>How to get faxstat or HylaFax to show status of all ttySx
>
>Tom
>
>
>
>
>---- Original message ----
>>Date: Thu, 13 Oct 2005 10:33:49 +0100
>>From: "support" <support@xxxxxxxxxxxx>
>>Subject: RE: regarding Q&A # 48
>>To: <tom@xxxxxxxxxxxxxx>
>>
>>Hi Tom.
>>
>>I don't have answers to your specific questions but will
>discuss with our
>>engineers and come back to you. While you are waiting I
>would suggest that
>>you post your questions to the HylaFAX users list because we
>have a lot of
>>customers who monitor this and may have solved your problem.
>>
>>Regards
>>
>>Mainpine Support
>>USA +1 718 701 2422 | Asia/Europe +44 1225 436137
>>support@xxxxxxxxxxxx | www.mainpine.com
>>
>>-----Original Message-----
>>From: Tom Miller [mailto:tom@xxxxxxxxxxxxxx]
>>Sent: 13 October 2005 06:46
>>To: support@xxxxxxxxxxxx
>>Subject: regarding Q&A # 48
>>
>>
>>Every time I mannually touched or modified the
>>/var/spool/hylafax/etc/config.ttyS4 the whole modem won't
>work any more. I
>>manually modified those ttySX three time.
>>two time required a reboot from the server. The third time
it
>still not
>>working until now. I am re-installing with the new version
>of hylafax 4.2.2
>>instead of 4.2.1. Hope, it will fix it by installing
>everything again. Any
>>thought?
>>
>>Thanks,
>>Tom
>>
>>
>>---- Original message ----
>>>Date: Tue, 13 Sep 2005 10:11:20 +0100
>>>From: "support" <support@xxxxxxxxxxxx>
>>>Subject: RE: [hylafax-users] Incoming fax doesn't work
>>>To: <tom@xxxxxxxxxxxxxx>
>>>
>>>Hi Tom.
>>>
>>>Class 1 and 1.0 are significantly more robust when used
with
>>HylaFAX.
>>>
>>>Regards
>>>
>>>Support
>>>Mainpine Ltd.
>>>e: support@xxxxxxxxxxxx
>>>w: http://www.mainpine.com
>>>t: +44(0) 1373 830888
>>>f: +44(0) 1373 830768
>>>
>>>-----Original Message-----
>>>From: Tom Miller [mailto:tom@xxxxxxxxxxxxxx]
>>>Sent: 13 September 2005 08:14
>>>To: support@xxxxxxxxxxxx
>>>Subject: Re: [hylafax-users] Incoming fax doesn't work
>>>
>>>Thank you.
>>>So Hylafax Class 1 driver is recommended for MainPine
board?
>>>
>>>Thanks much,
>>>Tom
>>>
>>>---- Original message ----
>>>>Date: Sun, 4 Sep 2005 12:10:54 +0100
>>>>From: "support" <support@xxxxxxxxxxxx>
>>>>Subject: Re: [hylafax-users] Incoming fax doesn't work
>>>>To: <tom@xxxxxxxxxxxxxx>, <hylafax-users@xxxxxxxxxxx>
>>>>
>>>>Hi Tom.
>>>>
>>>>Our support faq has answers to common HylaFAX questions
>>>(answers # 47 to
>>>>55), please take a look and let us know what's questions
>>>remain;
>>>>
>>>>http://www.mainpine.com/q_a.html
>>>>
>>>>I would also suggest that you upgrade to the latest
HylaFAX
>>>release
>>>>(4.2.2rc5) because of the work undertaken in the Class 1
>>>driver.
>>>>
>>>>Regards
>>>>
>>>>Support
>>>>Mainpine Ltd.
>>>>e: support@xxxxxxxxxxxx
>>>>w: http://www.mainpine.com
>>>>t: +44(0) 1373 830888
>>>>f: +44(0) 1373 830768
>>>>
>>>>-----Original Message-----
>>>>From: Tom Miller [mailto:tom@xxxxxxxxxxxxxx]
>>>>Sent: 04 September 2005 11:24
>>>>To: support@xxxxxxxxxxxx; hylafax-users@xxxxxxxxxxx
>>>>Subject: Incoming fax doesn't work
>>>>
>>>>
>>>>I have the following systems:
>>>>OS: RedHat ES 3.0
>>>>Hylafax: 4.2.1
>>>>Modem: 8 Port MainPine
>>>>
>>>>
>>>>I can send out fax but I can not receive any incoming fax.
>>>>There are not thing in the /var/spool/hylafax/recvq The
>>>modem does not seem
>>>>to pick up any incoming fax at all.
>>>>
>>>>
>>>>What am I missing here?
>>>>What do I need to verify?
>>>>
>>>>How can I temporary turn off the other 7 port
>>>>(ttyS5,ttyS6,ttyS7,ttyS8,ttyS9,ttyS10,ttyS11)
>>>>and just use the ttyS4 for testing/verfying incoming fax?
>>>>
>>>>In other world, can I force HylaFax to answer incoming
only
>>>on ttyS4? if
>>>>yes, How
>>>>
>>>>
>>>>Thanks much.
>>>>
>>>>Tom
>>>>
>>>>
>>>>
>>>>____________________ HylaFAX(tm) Users Mailing List
>>>_______________________
>>>> To subscribe/unsubscribe, click
>>>http://lists.hylafax.org/cgi-bin/lsg2.cgi
>>>> On UNIX: mail -s unsubscribe hylafax-users-
>>>request@xxxxxxxxxxx < /dev/null
>>>> *To learn about commercial HylaFAX(tm) support, mail
>>>sales@xxxxxxxxx*
>>>>
>>>
>>>
>>
>>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
