|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] 4.2.2 & Mainpine not working
I found the problem but do not know how to resovle it yet.
I have this these parameter in the /etc/sysctl.conf file.
For some reason it only can set two port at the reboot.
setserial /dev/ttyS4 port 0xAC80 irq 16 autoconfig ^fourport
setserial /dev/ttyS5 port 0xAC88 irq 16 autoconfig ^fourport
setserial /dev/ttyS6 port 0xAC90 irq 16 autoconfig ^fourport
setserial /dev/ttyS7 port 0xAC98 irq 16 autoconfig ^fourport
setserial /dev/ttyS8 port 0xACA0 irq 16 autoconfig ^fourport
setserial /dev/ttyS9 port 0xACA8 irq 16 autoconfig ^fourport
setserial /dev/ttyS10 port 0xACB0 irq 16 autoconfig ^fourport
setserial /dev/ttyS11 port 0xACB8 irq 16 autoconfig ^fourport
setserial /dev/ttyS4 set_multiport port1 0xACE0 mask1 0xFF
match1 0x00
After I set them to the above values and run fadaddmodem.
This is what I got.
[root@gabrielle software]# faxaddmodem
Serial port that modem is connected to []? ttyS5
Sorry, the device is currently in use by another program.
How do I disable and reserve the address and IRQ for this
modem?
---- Original message ----
>Date: Thu, 13 Oct 2005 21:09:32 -0400
>From: Tom Miller <tom@xxxxxxxxxxxxxx>
>Subject: 4.2.2 & Mainpine not working
>To: support@xxxxxxxxxxxx, hylafax-users@xxxxxxxxxxx
>
>guys,
>
>I am having problem with running either faxsetup or
>faxaddmodem for more than two port. I have a Oct+
>8 port MainPine. It only allow me to do a complete set
>up and detecting for only two ports (port ttyS4 and ttyS11)
>I am running hylafax 4.2.2 and RedHat ES 3.0. Please see
>the complain at the end of this email: Unable to deduce DTE-
>DCE speed; Any sugguestion?
>
>
>CountryCode: 1
>AreaCode: 587
>FAXNumber: +1.567.777.7777
>LongDistancePrefix: 1
>InternationalPrefix: 011
>DialStringRules: etc/dialrules
>SessionTracing: 11
>RingsBeforeAnswer: 1
>SpeakerVolume: high
>GettyArgs: "-h %l dx_%s"
>LocalIdentifier: "NothingSetup"
>TagLineFont: etc/lutRS18.pcf
>TagLineFormat: "From %%l|%c|Page %%P of %%T"
>MaxRecvPages: 25
>
>Are these ok [yes]?
>
>Now we are going to probe the tty port to figure out the type
>of modem that is attached. This takes a few seconds, so be
>patient.
>Note that if you do not have the modem cabled to the port,
or
>the
>modem is turned off, this may hang (just go and cable up the
>modem
>or turn it on, or whatever).
>
>Probing for best speed to talk to modem:
>Unable to deduce DTE-DCE speed; check that you are using the
>correct device and/or that your modem is setup properly. If
>all else fails, try the -s option to lock the speed.
>
>
>---- Original message ----
>>Date: Thu, 13 Oct 2005 11:36:07 -0400
>>From: Tom Miller <tom@xxxxxxxxxxxxxx>
>>Subject: 4.2.2 & Mainpine not working
>>To: support@xxxxxxxxxxxx, hylafax-users@xxxxxxxxxxx
>>
>>Does anyone have the same problem with version 4.2.2 and
>>Mainpine modem?
>>
>>I reinstall Hylafax 4.2.2 and went through the same faxsetup
>>as before for version 4.2.1 except one thing I used class =
>>1.0 instead of 1. The hylafax and modem doesn't pickup and
>>accept any incoming fax at all. I have 8 port MainPine
>Oct+ .
>> However, after ran the faxsetup modem only port ttyS4 and
>>ttyS11 were created the rest was not and have the following
>error:
>>
>>Probing for best speed to talk to modem:
>>Unable to deduce DTE-DCE speed; check that you are using the
>>correct device and/or that your modem is setup properly. If
>>all else fails, try the -s option to lock the speed.
>>
>>What happen to faxstat? It is different in 4.2.2
>>How to get faxstat or HylaFax to show status of all ttySx
>>
>>Tom
>>
>>
>>
>>
>>---- Original message ----
>>>Date: Thu, 13 Oct 2005 10:33:49 +0100
>>>From: "support" <support@xxxxxxxxxxxx>
>>>Subject: RE: regarding Q&A # 48
>>>To: <tom@xxxxxxxxxxxxxx>
>>>
>>>Hi Tom.
>>>
>>>I don't have answers to your specific questions but will
>>discuss with our
>>>engineers and come back to you. While you are waiting I
>>would suggest that
>>>you post your questions to the HylaFAX users list because
we
>>have a lot of
>>>customers who monitor this and may have solved your
problem.
>>>
>>>Regards
>>>
>>>Mainpine Support
>>>USA +1 718 701 2422 | Asia/Europe +44 1225 436137
>>>support@xxxxxxxxxxxx | www.mainpine.com
>>>
>>>-----Original Message-----
>>>From: Tom Miller [mailto:tom@xxxxxxxxxxxxxx]
>>>Sent: 13 October 2005 06:46
>>>To: support@xxxxxxxxxxxx
>>>Subject: regarding Q&A # 48
>>>
>>>
>>>Every time I mannually touched or modified the
>>>/var/spool/hylafax/etc/config.ttyS4 the whole modem won't
>>work any more. I
>>>manually modified those ttySX three time.
>>>two time required a reboot from the server. The third time
>it
>>still not
>>>working until now. I am re-installing with the new version
>>of hylafax 4.2.2
>>>instead of 4.2.1. Hope, it will fix it by installing
>>everything again. Any
>>>thought?
>>>
>>>Thanks,
>>>Tom
>>>
>>>
>>>---- Original message ----
>>>>Date: Tue, 13 Sep 2005 10:11:20 +0100
>>>>From: "support" <support@xxxxxxxxxxxx>
>>>>Subject: RE: [hylafax-users] Incoming fax doesn't work
>>>>To: <tom@xxxxxxxxxxxxxx>
>>>>
>>>>Hi Tom.
>>>>
>>>>Class 1 and 1.0 are significantly more robust when used
>with
>>>HylaFAX.
>>>>
>>>>Regards
>>>>
>>>>Support
>>>>Mainpine Ltd.
>>>>e: support@xxxxxxxxxxxx
>>>>w: http://www.mainpine.com
>>>>t: +44(0) 1373 830888
>>>>f: +44(0) 1373 830768
>>>>
>>>>-----Original Message-----
>>>>From: Tom Miller [mailto:tom@xxxxxxxxxxxxxx]
>>>>Sent: 13 September 2005 08:14
>>>>To: support@xxxxxxxxxxxx
>>>>Subject: Re: [hylafax-users] Incoming fax doesn't work
>>>>
>>>>Thank you.
>>>>So Hylafax Class 1 driver is recommended for MainPine
>board?
>>>>
>>>>Thanks much,
>>>>Tom
>>>>
>>>>---- Original message ----
>>>>>Date: Sun, 4 Sep 2005 12:10:54 +0100
>>>>>From: "support" <support@xxxxxxxxxxxx>
>>>>>Subject: Re: [hylafax-users] Incoming fax doesn't work
>>>>>To: <tom@xxxxxxxxxxxxxx>, <hylafax-users@xxxxxxxxxxx>
>>>>>
>>>>>Hi Tom.
>>>>>
>>>>>Our support faq has answers to common HylaFAX questions
>>>>(answers # 47 to
>>>>>55), please take a look and let us know what's questions
>>>>remain;
>>>>>
>>>>>http://www.mainpine.com/q_a.html
>>>>>
>>>>>I would also suggest that you upgrade to the latest
>HylaFAX
>>>>release
>>>>>(4.2.2rc5) because of the work undertaken in the Class 1
>>>>driver.
>>>>>
>>>>>Regards
>>>>>
>>>>>Support
>>>>>Mainpine Ltd.
>>>>>e: support@xxxxxxxxxxxx
>>>>>w: http://www.mainpine.com
>>>>>t: +44(0) 1373 830888
>>>>>f: +44(0) 1373 830768
>>>>>
>>>>>-----Original Message-----
>>>>>From: Tom Miller [mailto:tom@xxxxxxxxxxxxxx]
>>>>>Sent: 04 September 2005 11:24
>>>>>To: support@xxxxxxxxxxxx; hylafax-users@xxxxxxxxxxx
>>>>>Subject: Incoming fax doesn't work
>>>>>
>>>>>
>>>>>I have the following systems:
>>>>>OS: RedHat ES 3.0
>>>>>Hylafax: 4.2.1
>>>>>Modem: 8 Port MainPine
>>>>>
>>>>>
>>>>>I can send out fax but I can not receive any incoming
fax.
>>>>>There are not thing in the /var/spool/hylafax/recvq The
>>>>modem does not seem
>>>>>to pick up any incoming fax at all.
>>>>>
>>>>>
>>>>>What am I missing here?
>>>>>What do I need to verify?
>>>>>
>>>>>How can I temporary turn off the other 7 port
>>>>>(ttyS5,ttyS6,ttyS7,ttyS8,ttyS9,ttyS10,ttyS11)
>>>>>and just use the ttyS4 for testing/verfying incoming fax?
>>>>>
>>>>>In other world, can I force HylaFax to answer incoming
>only
>>>>on ttyS4? if
>>>>>yes, How
>>>>>
>>>>>
>>>>>Thanks much.
>>>>>
>>>>>Tom
>>>>>
>>>>>
>>>>>
>>>>>____________________ HylaFAX(tm) Users Mailing List
>>>>_______________________
>>>>> To subscribe/unsubscribe, click
>>>>http://lists.hylafax.org/cgi-bin/lsg2.cgi
>>>>> On UNIX: mail -s unsubscribe hylafax-users-
>>>>request@xxxxxxxxxxx < /dev/null
>>>>> *To learn about commercial HylaFAX(tm) support, mail
>>>>sales@xxxxxxxxx*
>>>>>
>>>>
>>>>
>>>
>>>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
