|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Missing EOL after 5 seconds (section 3.2/T.4)
Hello Everybody,
I have installed hylafax almost a year ago on a server, and it was working
ok, on Debian "Testing" Sarge, however i decide to upgrade the whole
system to the stable release using apt-get, and hylafax sudently decide to
not work again, because it show the following message on every fax it
tries to recieve:
Missing EOL after 5 seconds (section 3.2/T.4)
The modem is a Boca 14.400 bps RC144DPi Rev CA V1.410-AS29
I will like to stick to class2 because this fax supports adaptative answer
so nice, but currently fax is not working.
Any ideas ?
The configuration is the same (config.ttyS0):
CountryCode: 57
AreaCode: 1
FAXNumber: 123456
LongDistancePrefix: 09
InternationalPrefix: 009
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-r -b -s %s %l"
LocalIdentifier: "XXXXXXXXXX"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use class 2 interface
ModemRate: 19200
ModemFlowControl: rtscts # default
ModemWaitForConnect: yes # wait for CONNECT on answer
#
#ModemResetCmds: AT&F2 # what you want for a Supra
ModemNoFlowCmd: AT&K # disable flow control cmd
ModemHardFlowCmd: AT&K3 # hardware flow control cmd
ModemSoftFlowCmd: AT&K4 # software flow control cmd
ModemSetupDTRCmd: AT&D2 # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C1 # DCD follows carrier
ModemSetupAACmd: AT+FCLASS=0;+FAA=1 # enable in class 0
#ModemSetupAACmd: AT+FAA=1
AdaptiveAnswer: yes
#
ModemSendFillOrder: LSB2MSB # as expected
ModemRecvFillOrder: MSB2LSB # opposite of what makes sense
Class2RecvDataTrigger: "\022" # a la 2388-B
Class2APQueryCmd: none # prevent ERROR
Class2BUGCmd: none # prevent ERROR
Here is the error:
---- Transcript of session follows ----
Jun 17 09:26:30.18: [ 1288]: SESSION BEGIN 000002830 5714257020
Jun 17 09:26:30.18: [ 1288]: HylaFAX (tm) Version 4.2.1
Jun 17 09:26:30.18: [ 1288]: <-- [4:ATA\r]
Jun 17 09:26:41.69: [ 1288]: --> [3:FAX]
Jun 17 09:26:47.78: [ 1288]: --> [5:+FCON]
Jun 17 09:26:47.78: [ 1288]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jun 17 09:26:47.79: [ 1288]: RECV FAX: begin
Jun 17 09:26:49.43: [ 1288]: --> [29:+FTSI: "824104239 "]
Jun 17 09:26:49.43: [ 1288]: REMOTE TSI "824104239"
Jun 17 09:26:49.75: [ 1288]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 09:26:49.75: [ 1288]: REMOTE wants 9600 bit/s
Jun 17 09:26:49.75: [ 1288]: REMOTE wants A4 page width (215 mm)
Jun 17 09:26:49.75: [ 1288]: REMOTE wants unlimited page length
Jun 17 09:26:49.75: [ 1288]: REMOTE wants 3.85 line/mm
Jun 17 09:26:49.75: [ 1288]: REMOTE wants 2-D MR
Jun 17 09:26:49.86: [ 1288]: --> [2:OK]
Jun 17 09:26:49.86: [ 1288]: <-- [7:AT+FDR\r]
Jun 17 09:26:51.65: [ 1288]: --> [5:+FCFR]
Jun 17 09:26:53.86: [ 1288]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 09:26:53.86: [ 1288]: REMOTE wants 9600 bit/s
Jun 17 09:26:53.86: [ 1288]: REMOTE wants A4 page width (215 mm)
Jun 17 09:26:53.86: [ 1288]: REMOTE wants unlimited page length
Jun 17 09:26:53.86: [ 1288]: REMOTE wants 3.85 line/mm
Jun 17 09:26:53.86: [ 1288]: REMOTE wants 2-D MR
Jun 17 09:26:53.86: [ 1288]: --> [7:CONNECT]
Jun 17 09:26:53.86: [ 1288]: RECV: begin page
Jun 17 09:26:53.86: [ 1288]: RECV: send trigger 022
Jun 17 09:26:53.86: [ 1288]: Copy quality checking performed by host
Jun 17 09:28:13.86: [ 1288]: RECV: Missing EOL after 5 seconds
Jun 17 09:28:13.86: [ 1288]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)Jun 17 09:28:13.86: [ 1288]: RECV FAX: Missing
EOL after 5 seconds (section 3.2/T.4)
Jun 17 09:28:13.86: [ 1288]: <-- [6:AT+FK\r]
Jun 17 09:28:13.86: [ 1288]: RECV FAX (000002830): recvq/fax000002312.tif
from 824104239, route to <unspecified>, 0 pages in 1:26
Jun 17 09:28:13.97: [ 1288]: --> [8:+FHNG: 2]
Jun 17 09:28:13.97: [ 1288]: REMOTE HANGUP: Call aborted, from +FK or
<CAN> (code 2)
Jun 17 09:28:13.97: [ 1288]: MODEM Hang up
Jun 17 09:28:13.97: [ 1288]: RECV FAX (000002830): session with 824104239
terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
Jun 17 09:28:13.97: [ 1288]: RECV FAX: bin/faxrcvd
"recvq/fax000002312.tif" "ttyS0" "000002830" "Missing EOL after 5 seconds
(section 3.2/T.4)" "" ""
Jun 17 09:28:13.97: [ 1288]: RECV FAX: end
Jun 17 09:28:13.97: [ 1288]: SESSION END
Another one...
---- Transcript of session follows ----
Jun 17 11:28:23.39: [ 1274]: SESSION BEGIN 000002833 5714257020
Jun 17 11:28:23.39: [ 1274]: HylaFAX (tm) Version 4.2.1
Jun 17 11:28:23.39: [ 1274]: <-- [4:ATA\r]
Jun 17 11:28:34.79: [ 1274]: --> [3:FAX]
Jun 17 11:28:41.04: [ 1274]: --> [5:+FCON]
Jun 17 11:28:41.04: [ 1274]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jun 17 11:28:41.04: [ 1274]: RECV FAX: begin
Jun 17 11:28:42.70: [ 1274]: --> [29:+FTSI: " 4464770"]
Jun 17 11:28:42.74: [ 1274]: REMOTE TSI "4464770"
Jun 17 11:28:50.43: [ 1274]: --> [29:+FTSI: " 4464770"]
Jun 17 11:28:50.44: [ 1274]: REMOTE TSI "4464770"
Jun 17 11:28:50.77: [ 1274]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 11:28:50.78: [ 1274]: REMOTE wants 9600 bit/s
Jun 17 11:28:50.78: [ 1274]: REMOTE wants A4 page width (215 mm)
Jun 17 11:28:50.78: [ 1274]: REMOTE wants unlimited page length
Jun 17 11:28:50.78: [ 1274]: REMOTE wants 3.85 line/mm
Jun 17 11:28:50.78: [ 1274]: REMOTE wants 2-D MR
Jun 17 11:28:50.88: [ 1274]: --> [2:OK]
Jun 17 11:28:50.89: [ 1274]: <-- [7:AT+FDR\r]
Jun 17 11:28:52.67: [ 1274]: --> [5:+FCFR]
Jun 17 11:28:54.75: [ 1274]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 11:28:54.75: [ 1274]: REMOTE wants 9600 bit/s
Jun 17 11:28:54.75: [ 1274]: REMOTE wants A4 page width (215 mm)
Jun 17 11:28:54.75: [ 1274]: REMOTE wants unlimited page length
Jun 17 11:28:54.75: [ 1274]: REMOTE wants 3.85 line/mm
Jun 17 11:28:54.75: [ 1274]: REMOTE wants 2-D MR
Jun 17 11:28:54.75: [ 1274]: --> [7:CONNECT]
Jun 17 11:28:54.76: [ 1274]: RECV: begin page
Jun 17 11:28:54.77: [ 1274]: RECV: send trigger 022
Jun 17 11:28:54.77: [ 1274]: Copy quality checking performed by host
Jun 17 11:30:14.82: [ 1274]: RECV: Missing EOL after 5 seconds
Jun 17 11:30:14.83: [ 1274]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)Jun 17 11:30:14.88: [ 1274]: RECV FAX: Missing
EOL after 5 seconds (section 3.2/T.4)
Jun 17 11:30:14.88: [ 1274]: <-- [6:AT+FK\r]
Jun 17 11:30:14.93: [ 1274]: RECV FAX (000002833): recvq/fax000002314.tif
from 4464770, route to <unspecified>, 0 pages in 1:33
Jun 17 11:30:14.98: [ 1274]: --> [8:+FHNG: 2]
Jun 17 11:30:14.98: [ 1274]: REMOTE HANGUP: Call aborted, from +FK or
<CAN> (code 2)
Jun 17 11:30:14.98: [ 1274]: MODEM Hang up
Jun 17 11:30:15.01: [ 1274]: RECV FAX (000002833): session with 4464770
terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
Jun 17 11:30:15.01: [ 1274]: RECV FAX: bin/faxrcvd
"recvq/fax000002314.tif" "ttyS0" "000002833" "Missing EOL after 5 seconds
(section 3.2/T.4)" "" ""
Jun 17 11:30:15.01: [ 1274]: RECV FAX: end
Jun 17 11:30:15.01: [ 1274]: SESSION END
and another....
---- Transcript of session follows ----
Jun 17 12:39:43.51: [ 1274]: SESSION BEGIN 000002837 5714257020
Jun 17 12:39:43.51: [ 1274]: HylaFAX (tm) Version 4.2.1
Jun 17 12:39:43.52: [ 1274]: <-- [4:ATA\r]
Jun 17 12:39:55.36: [ 1274]: --> [3:FAX]
Jun 17 12:40:01.59: [ 1274]: --> [5:+FCON]
Jun 17 12:40:01.60: [ 1274]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Jun 17 12:40:01.60: [ 1274]: RECV FAX: begin
Jun 17 12:40:03.27: [ 1274]: --> [29:+FTSI: " 2409220"]
Jun 17 12:40:03.29: [ 1274]: REMOTE TSI "2409220"
Jun 17 12:40:03.62: [ 1274]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 12:40:03.62: [ 1274]: REMOTE wants 9600 bit/s
Jun 17 12:40:03.62: [ 1274]: REMOTE wants A4 page width (215 mm)
Jun 17 12:40:03.62: [ 1274]: REMOTE wants unlimited page length
Jun 17 12:40:03.62: [ 1274]: REMOTE wants 3.85 line/mm
Jun 17 12:40:03.63: [ 1274]: REMOTE wants 2-D MR
Jun 17 12:40:03.73: [ 1274]: --> [2:OK]
Jun 17 12:40:03.74: [ 1274]: <-- [7:AT+FDR\r]
Jun 17 12:40:05.53: [ 1274]: --> [5:+FCFR]
Jun 17 12:40:07.59: [ 1274]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 12:40:07.60: [ 1274]: REMOTE wants 9600 bit/s
Jun 17 12:40:07.60: [ 1274]: REMOTE wants A4 page width (215 mm)
Jun 17 12:40:07.60: [ 1274]: REMOTE wants unlimited page length
Jun 17 12:40:07.60: [ 1274]: REMOTE wants 3.85 line/mm
Jun 17 12:40:07.60: [ 1274]: REMOTE wants 2-D MR
Jun 17 12:40:07.60: [ 1274]: --> [7:CONNECT]
Jun 17 12:40:07.60: [ 1274]: RECV: begin page
Jun 17 12:40:07.60: [ 1274]: RECV: send trigger 022
Jun 17 12:40:07.60: [ 1274]: Copy quality checking performed by host
Jun 17 12:41:27.62: [ 1274]: RECV: Missing EOL after 5 seconds
Jun 17 12:41:27.63: [ 1274]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)Jun 17 12:41:27.66: [ 1274]: RECV FAX: Missing
EOL after 5 seconds (section 3.2/T.4)
Jun 17 12:41:27.66: [ 1274]: <-- [6:AT+FK\r]
Jun 17 12:41:27.75: [ 1274]: RECV FAX (000002837): recvq/fax000002318.tif
from 2409220, route to <unspecified>, 0 pages in 1:26
Jun 17 12:41:27.76: [ 1274]: --> [8:+FHNG: 2]
Jun 17 12:41:27.76: [ 1274]: REMOTE HANGUP: Call aborted, from +FK or
<CAN> (code 2)
Jun 17 12:41:27.76: [ 1274]: MODEM Hang up
Jun 17 12:41:27.76: [ 1274]: RECV FAX (000002837): session with 2409220
terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
Jun 17 12:41:27.76: [ 1274]: RECV FAX: bin/faxrcvd
"recvq/fax000002318.tif" "ttyS0" "000002837" "Missing EOL after 5 seconds
(section 3.2/T.4)" "" ""
Jun 17 12:41:27.76: [ 1274]: RECV FAX: end
Jun 17 12:41:27.76: [ 1274]: SESSION END
Slds.
--
Nestor A. Diaz
Ingeniero de Sistemas y Comp.
Tel. +57 1 6005490
Cel. +57 315 8190760
nestor@xxxxxxxxxxxxxxx
http://www.tiendalinux.com
Bogota, Colombia
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
