Re: [hylafax-users] faxgetty flailing and failing.

[Jean-Pierre Radley <jpr@xxxxxxx>]

Lee Howard typed (on Mon, Jan 10, 2005 at 04:39:44PM -0800):
| On 2005.01.10 14:46 Jean-Pierre Radley wrote:
| >Lee Howard typed (on Mon, Jan 10, 2005 at 02:43:03PM -0800):
| >| On 2005.01.10 14:35 Jean-Pierre Radley wrote:
| >| >Lee Howard typed (on Mon, Jan 10, 2005 at 02:20:01PM -0800):
| >|
| >| >| Can you communicate with the modem using some other terminal
| >program
| >| >| on tty2A?
| >| >|
| >| >
| >| >Easily.  Using xc:
| >|
| >| Did faxaddmodem go okay?
| >
| >Yes, quite normally.
| 
| Well, my initial guess, then, would be that it has to do with 
| raising/lowering DTR.  You may want to read through the DTR-related 
| issues in 'man hylafax-config' and see if altering the settings makes 
| any difference for you.
| 

Some progress now.  I had configured the Hayes with &D3, a setting I just
use without thinking.  The setting took, and was recorded in NV-RAM, but
obviously was not useful.

I changed that to &D2, and tried to send to my own Hylafax modem.  Now
I'm getting:


The full document was not received because:

    Failed to properly detect high-speed data carrier.

    ---- Transcript of session follows ----

Jan 11 12:20:23.80: [11449]: SESSION BEGIN 000001699 12128770260
Jan 11 12:20:23.80: [11449]: HylaFAX (tm) Version 4.2.0
Jan 11 12:20:23.83: [11449]: <-- [4:ATA\r]
Jan 11 12:20:29.95: [11449]: --> [7:CONNECT]
Jan 11 12:20:29.95: [11449]: ANSWER: FAX CONNECTION  DEVICE '/dev/tty1A'
Jan 11 12:20:29.95: [11449]: RECV FAX: begin
Jan 11 12:20:31.86: [11449]: --> [7:CONNECT]
Jan 11 12:20:32.69: [11449]: --> [7:CONNECT]
Jan 11 12:20:33.24: [11449]: --> [2:OK]
Jan 11 12:20:33.24: [11449]: <-- [9:AT+FRH=3\r]
Jan 11 12:20:33.76: [11449]: --> [7:CONNECT]
Jan 11 12:20:35.19: [11449]: --> [2:OK]
Jan 11 12:20:35.19: [11449]: REMOTE TSI "SSC Consolidation"
Jan 11 12:20:35.19: [11449]: <-- [9:AT+FRH=3\r]
Jan 11 12:20:35.22: [11449]: --> [7:CONNECT]
Jan 11 12:20:35.46: [11449]: --> [2:OK]
Jan 11 12:20:35.46: [11449]: REMOTE wants 14400 bit/s
Jan 11 12:20:35.46: [11449]: REMOTE wants A4 page width (215 mm)
Jan 11 12:20:35.46: [11449]: REMOTE wants unlimited page length
Jan 11 12:20:35.46: [11449]: REMOTE wants 3.85 line/mm
Jan 11 12:20:35.46: [11449]: REMOTE wants 2-D MMR
Jan 11 12:20:35.46: [11449]: REMOTE wants T.30 Annex A, 256-byte ECM
Jan 11 12:20:35.46: [11449]: RECV training at v.17 14400 bit/s
Jan 11 12:20:35.49: [11449]: <-- [11:AT+FRM=145\r]
Jan 11 12:20:37.04: [11449]: --> [7:CONNECT]
Jan 11 12:20:38.10: [11449]: RECV: TCF 1804 bytes, 5% non-zero, 1699 zero-run
Jan 11 12:20:38.10: [11449]: RECV: reject TCF (zero run too short, min 1800)
Jan 11 12:20:38.10: [11449]: --> [10:NO CARRIER]
Jan 11 12:20:38.10: [11449]: DELAY 75 ms
Jan 11 12:20:38.18: [11449]: <-- [9:AT+FTH=3\r]
Jan 11 12:20:38.23: [11449]: --> [7:CONNECT]
Jan 11 12:20:39.53: [11449]: --> [2:OK]
Jan 11 12:20:39.53: [11449]: TRAINING failed
Jan 11 12:20:39.53: [11449]: <-- [9:AT+FRH=3\r]
Jan 11 12:20:42.47: [11449]: --> [7:CONNECT]
Jan 11 12:20:43.93: [11449]: --> [2:OK]
Jan 11 12:20:43.93: [11449]: REMOTE TSI "SSC Consolidation"
Jan 11 12:20:43.93: [11449]: <-- [9:AT+FRH=3\r]
Jan 11 12:20:43.96: [11449]: --> [7:CONNECT]
Jan 11 12:20:44.19: [11449]: --> [2:OK]
Jan 11 12:20:44.19: [11449]: REMOTE wants 9600 bit/s
Jan 11 12:20:44.19: [11449]: REMOTE wants A4 page width (215 mm)
Jan 11 12:20:44.19: [11449]: REMOTE wants unlimited page length
Jan 11 12:20:44.19: [11449]: REMOTE wants 3.85 line/mm
Jan 11 12:20:44.19: [11449]: REMOTE wants 2-D MMR
Jan 11 12:20:44.19: [11449]: REMOTE wants T.30 Annex A, 256-byte ECM
Jan 11 12:20:44.19: [11449]: RECV training at v.29 9600 bit/s
Jan 11 12:20:44.22: [11449]: <-- [10:AT+FRM=96\r]
Jan 11 12:20:44.64: [11449]: --> [7:CONNECT]
Jan 11 12:20:46.27: [11449]: RECV: TCF 1890 bytes, 4% non-zero, 1801 zero-run
Jan 11 12:20:46.27: [11449]: --> [10:NO CARRIER]
Jan 11 12:20:46.27: [11449]: DELAY 75 ms
Jan 11 12:20:46.35: [11449]: TRAINING succeeded
Jan 11 12:20:46.35: [11449]: ACCEPT TSI "SSC Consolidation"
Jan 11 12:20:46.35: [11449]: <-- [9:AT+FTH=3\r]
Jan 11 12:20:46.40: [11449]: --> [7:CONNECT]
Jan 11 12:20:47.70: [11449]: --> [2:OK]
Jan 11 12:20:47.73: [11449]: <-- [10:AT+FRM=96\r]
Jan 11 12:20:50.67: [11449]: --> [8:+FCERROR]
Jan 11 12:20:50.67: [11449]: <-- [10:AT+FRM=96\r]
Jan 11 12:20:51.06: [11449]: --> [8:+FCERROR]
Jan 11 12:20:51.06: [11449]: <-- [10:AT+FRM=96\r]
Jan 11 12:20:51.45: [11449]: --> [8:+FCERROR]
Jan 11 12:20:51.45: [11449]: <-- [10:AT+FRM=96\r]
Jan 11 12:20:58.60: [11449]: --> [2:OK]
Jan 11 12:20:58.63: [11449]: RECV FAX (000001699): from SSC Consolidation, page 1 in 0:12, INF, 3.85 line/mm, 2-D MMR, 9600 bit/s
Jan 11 12:20:58.63: [11449]: RECV FAX (000001699): recvq/fax000000892.tif from SSC Consolidation, route to <unspecified>, 1 pages in 0:29
Jan 11 12:20:58.63: [11449]: RECV FAX: Failed to properly detect high-speed data carrier.
Jan 11 12:20:58.63: [11449]: <-- [9:AT+FTH=3\r]
Jan 11 12:20:58.68: [11449]: --> [7:CONNECT]
Jan 11 12:20:59.98: [11449]: --> [2:OK]
Jan 11 12:20:59.98: [11449]: RECV FAX (000001699): session with SSC Consolidation terminated abnormally: Failed to properly detect high-speed data carrier.
Jan 11 12:20:59.98: [11449]: RECV FAX: bin/faxrcvd "recvq/fax000000892.tif" "tty1A" "000001699" "Failed to properly detect high-speed data carrier." "" ""
Jan 11 12:20:59.98: [11449]: RECV FAX: end
Jan 11 12:20:59.98: [11449]: SESSION END



-- 
JP

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*