[hylafax-users] T.30 T2 timeout, expected page not received

["Ciro La Ferrara" <webmaster@xxxxxxxxxx>]

Hi I have this error:

Oct 18 12:16:18.85: [21976]: SESSION BEGIN 000000005 390818420130
Oct 18 12:16:18.85: [21976]: HylaFAX (tm) Version 4.2.0
Oct 18 12:16:18.85: [21976]: <-- [4:ATA\r]
Oct 18 12:16:23.85: [21976]: --> [7:CONNECT]
Oct 18 12:16:23.85: [21976]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Oct 18 12:16:23.85: [21976]: RECV FAX: begin
Oct 18 12:16:23.85: [21976]: <-- data [32]
Oct 18 12:16:23.85: [21976]: <-- data [2]
Oct 18 12:16:25.23: [21976]: --> [7:CONNECT]
Oct 18 12:16:25.23: [21976]: <-- data [23]
Oct 18 12:16:25.23: [21976]: <-- data [2]
Oct 18 12:16:25.99: [21976]: --> [7:CONNECT]
Oct 18 12:16:25.99: [21976]: <-- data [10]
Oct 18 12:16:25.99: [21976]: <-- data [2]
Oct 18 12:16:26.43: [21976]: --> [2:OK]
Oct 18 12:16:26.43: [21976]: <-- [9:AT+FRH=3\r]
Oct 18 12:16:27.14: [21976]: --> [7:CONNECT]
Oct 18 12:16:28.96: [21976]: --> [2:OK]
Oct 18 12:16:28.96: [21976]: REMOTE TSI "0547330781"
Oct 18 12:16:28.96: [21976]: <-- [9:AT+FRH=3\r]
Oct 18 12:16:28.99: [21976]: --> [7:CONNECT]
Oct 18 12:16:29.31: [21976]: --> [2:OK]
Oct 18 12:16:29.31: [21976]: REMOTE wants 9600 bit/s
Oct 18 12:16:29.31: [21976]: REMOTE wants A4 page width (215 mm)
Oct 18 12:16:29.31: [21976]: REMOTE wants unlimited page length
Oct 18 12:16:29.31: [21976]: REMOTE wants 3.85 line/mm
Oct 18 12:16:29.31: [21976]: REMOTE wants 1-D MH
Oct 18 12:16:29.31: [21976]: RECV training at v.29 9600 bit/s
Oct 18 12:16:29.31: [21976]: <-- [10:AT+FRM=96\r]
Oct 18 12:16:29.66: [21976]: --> [7:CONNECT]
Oct 18 12:16:31.17: [21976]: RECV: TCF 1792 bytes, 0% non-zero, 1778
zero-run
Oct 18 12:16:31.18: [21976]: --> [10:NO CARRIER]
Oct 18 12:16:31.18: [21976]: DELAY 75 ms
Oct 18 12:16:31.26: [21976]: TRAINING succeeded
Oct 18 12:16:31.26: [21976]: <-- [9:AT+FTH=3\r]
Oct 18 12:16:31.30: [21976]: --> [7:CONNECT]
Oct 18 12:16:31.30: [21976]: <-- data [3]
Oct 18 12:16:31.30: [21976]: <-- data [2]
Oct 18 12:16:32.04: [21976]: --> [2:OK]
Oct 18 12:16:32.04: [21976]: <-- [10:AT+FRM=96\r]
Oct 18 12:16:32.79: [21976]: --> [7:CONNECT]
Oct 18 12:16:32.79: [21976]: RECV: begin page
Oct 18 12:16:53.99: [21976]: RECV: 343 total lines, 9 bad lines, 3
consecutive bad lines
Oct 18 12:16:53.99: [21976]: RECV: end page
Oct 18 12:16:53.99: [21976]: --> [10:NO CARRIER]
Oct 18 12:16:53.99: [21976]: <-- [9:AT+FRH=3\r]
Oct 18 12:16:54.46: [21976]: --> [7:CONNECT]
Oct 18 12:16:59.46: [21976]: <-- data [1]
Oct 18 12:16:59.57: [21976]: --> [2:OK]
Oct 18 12:16:59.57: [21976]: RECV keeping unconfirmed page
Oct 18 12:16:59.57: [21976]: RECV FAX (000000005): from 0547330781, page 1
in 0:28, INF, 3.85 line/mm, 1-D MH, 9600 bit/s
Oct 18 12:16:59.57: [21976]: RECV FAX (000000005): recvq/fax000000005.tif
from 0547330781, route to <unspecified>, 1 pages in 0:36
Oct 18 12:16:59.57: [21976]: RECV FAX: T.30 T2 timeout, expected page not
received
Oct 18 12:16:59.57: [21976]: <-- [9:AT+FTH=3\r]
Oct 18 12:16:59.71: [21976]: --> [7:CONNECT]
Oct 18 12:16:59.71: [21976]: <-- data [3]
Oct 18 12:16:59.71: [21976]: <-- data [2]
Oct 18 12:17:00.45: [21976]: --> [2:OK]
Oct 18 12:17:00.45: [21976]: RECV FAX (000000005): session with 0547330781
terminated abnormally: T.30 T2 timeout, expected page not
 received
Oct 18 12:17:00.45: [21976]: RECV FAX: bin/faxrcvd "recvq/fax000000005.tif"
"ttyS0" "000000005" "T.30 T2 timeout, expected page not
received" "" ""
Oct 18 12:17:00.45: [21976]: RECV FAX: end
Oct 18 12:17:00.46: [21976]: SESSION END

This is my conf:

CountryCode:            39
AreaCode:               2
FAXNumber:              +39.xxx.xxx.xxx.xx
LongDistancePrefix:     5
InternationalPrefix:    011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
PercentGoodLines:       90
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use this to supply a hint
ModemRate:              57600           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # RTS/CTS flow control assumed
#
ModemSoftFlowCmd:       AT\Q1           # set desired flow control method
ModemHardFlowCmd:       AT\Q3           # set desired flow control method
ModemSetupDTRCmd:       AT&D3           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD follows carrier
ModemDialCmd:           ATDT%s
#
# Happy days!  This modem has proper support for querying
# the model, manufacturer, and firmware revision!
#
ModemMfrQueryCmd:       AT+FMFR?
ModemModelQueryCmd:     AT+FMDL?
ModemRevQueryCmd:       AT+FREV?

Class1SwitchingCmd:  "<delay:7>"

Ideas?

Ciro La Ferrara


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*