[hylafax-users] I need a config file for my modem!!

Hi everyone!

I need a perfect config file for my Zyxel OMNI 56K faxmodem..

I tried out every chance (Class2 & Class1, rtscts & xonxoff, 19200 & 38400), everything!

However, I get all kinds of error:

-Unspecified Phase C error.. and B..

-Failure to train remote modem at 2400 bps or minimum speed

-Invalid dialing command

And I cannot fix these problems!?

Please, Somebody help me!! :\

My present config file:

CountryCode: 36

AreaCode: 1

FAXNumber: ***********

LongDistancePrefix: 06

InternationalPrefix: 00

DialStringRules: etc/dialrules

#ServerTracing: 0x08501

ServerTracing: 0xFFF

SessionTracing: 0x08501

RecvFileMode: 0644

LogFileMode: 0640

DeviceMode: 0660

RingsBeforeAnswer: 1

SpeakerVolume: off

GettyArgs: "-r -b %l"

PriorityScheduling: yes

TagLineFormat: "From %%l|%c|Page %%P of %%T"

MaxRecvPages: 50

ModemType: Class2 # use this to supply a hint

ModemRate: 19200 # max rate for DCE-DTE communication

#ModemFlowControl: xonxoff # XON/XOFF flow control assumed

ModemFlowControl: rtscts

#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem

#ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)

#ModemResetCmds: "" # stuff to do when modem is reset

#ModemAnswerCmd: ATA # use this to answer phone

#ModemNoFlowCmd: AT&K # disable flow control cmd

#ModemHardFlowCmd: AT&K3 # hardware flow control cmd

#ModemSoftFlowCmd: AT&K4 # software flow control cmd

#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer

# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.

# Note that we both turn the speaker on/off and set volume.

#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"

#ModemEchoOffCmd: ATE0 # disable command echo

#ModemVerboseResultsCmd: ATV1 # enable verbose command results

#ModemResultCodesCmd: ATQ0 # enable result codes

#ModemOnHookCmd: ATH0 # place phone on hook (hangup)

#ModemSoftResetCmd: ATZ # do soft reset of modem

#ModemSoftResetCmdDelay: 3000 # pause after soft reset

#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier

#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds

#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile

#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit

# Configuration parameters for Class 2 modems.

Class2Cmd: AT+FCLASS=2 # command to enter class 2

Class2BORCmd: AT+FBOR=0 # bit order for phase B/C/D (direct)

Class2RELCmd: AT+FREL=1 # byte-align EOL codes on recv

Class2CQCmd: "" # commands to enable copy quality proc.

Class2AbortCmd: AT+FK # abort session command

Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities

Class2DCCQueryCmd: AT+FDCC=? # query for modem capabilities

Class2TBCCmd: AT+FTBC=0 # setup stream mode

Class2CRCmd: AT+FCR=1 # enable capability to receive

Class2PHCTOCmd: AT+FPHCTO=30 # set phase C timeout parameter

Class2BUGCmd: AT+FBUG=1 # enable HDLC frame tracing

Class2LIDCmd: AT+FLID # set local identifier command

Class2DCCCmd: AT+FDCC # set modem capabilities command

Class2DISCmd: AT+FDIS # set session parameters command

Class2DDISCmd: "" # disable pre-dial DIS command hack

Class2CIGCmd: AT+FCIG # set polling identifier command

Class2PTSCmd: AT+FPTS # set post-page status command

Class2SPLCmd: AT+FSPL # set polling indicator command

# If Class2RecvDataTrigger is not set, then it is set to DC1

Class2RecvDataTrigger: "" # character sent to modem to start recv

Class2XmitWaitForXON: yes # if true, wait for XON before send

Thanks in advance!!

-Balazs