Re: [hylafax-users] What's the problem!? Unspecified Phase C error.. and now, Failure to train remote modem at 2400 bps or minimum speed

[Kónya Balázs <b.konya@xxxxxxxxxxx>]

It's funny...a part of my mail hid..

Sorry..
So my sending log (Failure to train remote modem at 2400 bps or minimum
speed) :

Oct 14 15:11:34.50: [12307]: SESSION BEGIN 000000193 36194610452
Oct 14 15:11:34.50: [12307]: HylaFAX (tm) Version 4.2.0
Oct 14 15:11:34.50: [12307]: SEND FAX: JOB 13 DEST 9,4610452 COMMID
000000193 DEVICE '/dev/ttyS0'
Oct 14 15:11:34.50: [12307]: STATE CHANGE: RUNNING -> SENDING
Oct 14 15:11:34.50: [12307]: sched policy=1, priority=1
Oct 14 15:13:03.21: [12307]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Oct 14 15:13:03.21: [12307]: sched policy=0, priority=0
Oct 14 15:13:03.21: [12307]: SESSION END

Thanks in advance..

-----Original Message-----
From: Pedro Rocadas [mailto:procadas@xxxxxxxxx] 
Sent: Thursday, October 14, 2004 4:05 PM
To: Ksnya Balazs
Subject: RE: [hylafax-users] What's the problem!? Unspecified Phase C
error..

And? If the situation persists, please, send a log
session the mailling list so developers could analise
it. Your phase C error could come from buggy modem
firmware too.

--- Kónya Balázs <b.konya@xxxxxxxxxxx> wrote:

> My new config.file:
> 
> CountryCode:		36
> AreaCode:		1
> FAXNumber:		"**********"
> LongDistancePrefix:	06
> InternationalPrefix:	00
> DialStringRules:	etc/dialrules
> ServerTracing:		0x08501
> SessionTracing:		0x08501
> RecvFileMode:		0644
> LogFileMode:		0640
> DeviceMode:		0660
> RingsBeforeAnswer:	1
> SpeakerVolume:		off
> GettyArgs:		"-r -b %l"
> PriorityScheduling:	yes
> TagLineFormat:		"From %%l|%c|Page %%P of %%T"
> MaxRecvPages:		50
> 
> ModemType:		Class1		# use this to supply a hint
> #ModemRate:		19200		# rate for DCE-DTE communication
> #ModemFlowControl:	xonxoff		# XON/XOFF flow control
> assumed
> #
> #ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets
> modem
> #ModemSetupDCDCmd:	AT&C1		# setup so DCD follows
> carrier
> #GettyArgs:		"-h %l dx_%s"	# modem must auto-detect
> fax/data
> 
> #ModemResetCmds:		""		# stuff to do when modem
> is reset
> #ModemAnswerCmd:		ATA		# use this to answer
> phone
> #ModemNoFlowCmd:		AT&K		# disable flow control
> cmd
> #ModemHardFlowCmd:	AT&K3		# hardware flow control
> cmd
> #ModemSoftFlowCmd:	AT&K4		# software flow control
> cmd
> #ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
> 
> #ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1
> ATL3M1"
> #ModemEchoOffCmd:	ATE0		# disable command echo
> #ModemVerboseResultsCmd:	ATV1		# enable verbose
> command
> results
> #ModemResultCodesCmd:	ATQ0		# enable result codes
> #ModemOnHookCmd:		ATH0		# place phone on hook
> (hangup)
> #ModemSoftResetCmd:	ATZ		# do soft reset of modem
> #ModemSoftResetCmdDelay:	3000	# pause after soft
> reset
> #ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for
> carrier
> #ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time
> is 2
> seconds
> #ModemRecvFillOrder:	LSB2MSB		# bit order of
> received
> facsimile
> #ModemSendFillOrder:	LSB2MSB		# bit order modem
> expects for
> transmit
> 
> Class1Cmd:		AT+FCLASS=1	# command to enter class 1
> Class1PPMWaitCmd:	AT+FTS=7	# command to stop and
> wait
> before PPM
> Class1TCFWaitCmd:	AT+FTS=7	# command to stop and
> wait
> before TCF
> Class1EOPWaitCmd:	AT+FTS=9	# command to stop and
> wait
> before EOP
> Class1MsgRecvHackCmd:	""	# command to avoid +FCERROR
> before image
> Class1TCFResponseDelay:	75		# 75ms delay between
> recv TCF &
> response
> Class1SendMsgDelay:	200		# 75ms delay after training
> Class1SwitchingCmd:	AT+FRS=7	# silence between HDLC
> recv and
> trans
> Class1TrainingRecovery:	1500		# 1.5sec delay after
> training
> failure
> Class1RecvAbortOK:	200		# wait 200ms for abort
> response
> Class1FrameOverhead:	4		# 4 byte overhead in recvd
> HDLC
> frames
> Class1RecvIdentTimer:	40000		# 35+5secs waiting for
> ident
> frames
> Class1TCFMaxNonZero:	10		# max 10% of data may be
> non-zero
> Class1TCFMinRun:	1000		# min run is 2/3rds of TCF
> duration
> 
> -----Original Message-----
> From: hylafax-users-bounce@xxxxxxxxxxx
> [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf
> Of Pedro Rocadas
> Sent: Thursday, October 14, 2004 3:24 PM
> To: hylafax-users@xxxxxxxxxxx
> Subject: Re: [hylafax-users] What's the problem!?
> Unspecified Phase C
> error..
> 
> Change to Class1. If you are using a modem from
> USRobotics, search tha mailling list archives for a
> working configuraton file.
> 
> 
> 



		
_______________________________
Do you Yahoo!?
Express yourself with Y! Messenger! Free. Download now. 
http://messenger.yahoo.com




____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*