I am using : libtiff-3.5.7-13
I figured that it wouldn't be the modem since the modem seems to
receive it ok ( faxgetty shows two pages in the messages log ). But,
since there have been no other sugguestions, what type of modem would
you sugguest I try? Looking mainly at external serial modems, I
probably have a bunch lying around in boxes between myself and
co-workers, so we should be able to find something that works.
Justin
On Thu, Sep 16, 2004 at 01:27:58AM -0700, Pedro Rocadas wrote:
> Well, you are using Red Hat E3, and I think your
> libtiff is a good one (< 3.6.1), but it worth checking
> out. If it's >= 3.6.1, you should downgrade, see
> http://bugs.hylafax.org/bugzilla/show_bug.cgi?id=500
>
> Otherwise, you must blame your USR firmware.
>
> --- Justin Rush <jrush@xxxxxxxxxxxxxx> wrote:
>
> > from my config file for ttyS1:
> > --
> > # Modem-related stuff: should reflect modem command
> > interface
> > # and hardware connection/cabling (e.g. flow
> > control).
> > #
> > ModemType: Class1 # use class
> > 1 interface
> > ModemRate: 19200 # rate for
> > DCE-DTE communication
> > ModemFlowControl: xonxoff # software
> > flow control
> > #
> > ModemSetupDTRCmd: ATS13=1&D2 # setup so
> > DTR drop resets modem
> > ModemSetupDCDCmd: AT&C1 # setup so
> > DCD reflects carrier (or not)
> > ModemNoFlowCmd: AT&H0&I0&R1 # setup
> > modem for no flow control
> > ModemHardFlowCmd: AT&H1&I0&R2 # setup
> > modem for hardware flow control
> > ModemSoftFlowCmd: AT&H2&I2&R1 # setup
> > modem for software flow control
> > ModemResultCodesCmd: ATQ0X4 # enable
> > result codes
> > #
> > ModemMfrQueryCmd: !USR
> > ModemModelQueryCmd: ATI3
> > ModemRevQueryCmd: ATI7 # XXX
> > returns a multi-line result
> > #
> > # When AT+FCLASS=1 is issued the modem automatically
> > switches
> > # to software flow control; these parameters let the
> > fax software
> > # reset flow control as needed after entering Class
> > 1.
> > #
> > Class1NFLOCmd: AT&H0&I0&R1 # setup
> > modem for no flow control
> > Class1HFLOCmd: AT&H1&I0&R2 # setup
> > modem for hardware flow control
> > Class1SFLOCmd: "" # modem does
> > this automatically
> > #
> > # This should resolve "DIS/DTC received 3 times"
> > errors:
> > #
> > Class1ResponseWaitCmd: AT+FRS=1 # wait after
> > sending TCF for response
> > #
> > # The remainder of this configuration is included so
> > that the
> > # modem "idles" in Class 0 while not sending or
> > receiving facsimile.
> > #
> > ModemSetupAACmd: AT+FCLASS=0 # leave
> > modem idling in class 0
> > ModemAnswerCmd: AT+FCLASS=1A # answer in
> > Class 1
> > #
> > # Disables the reporting of bad frames by the modem.
> > This
> > # overcomes a firmware problem in the x2 and V90
> > Sportsters.
> > # It is not necessary for the Courier modem.
> > #
> > Class2NRCmd: AT+FNR=1,1,1,0
> > --
> > The modem is an old USR Courrier modem. It seems
> > that the modem is receiving the fax properly but the
> > internals of hylafax just aren't handling the fax
> > properly.
> >
> > Anything else I can check?
> >
> > Thanks,
> > Justin
> >
> >
> > On Mon, Sep 13, 2004 at 11:50:17AM -0700, Pedro
> > Rocadas wrote:
> > > Did you configured your modem in CLass1? What is
> > the
> > > value of ModemFlowControl in your config.ttyS1
> > file?
> > > if it's not xonxoff try it. Other thing, you are
> > using
> > > a USR modem so, I definittly recommend you hylafax
> > > 4.2.0, but if you want a better advice, throw away
> > > that USR and buy a Multitech or a Zoom modem.
> > >
> > > --- Justin Rush <jrush@xxxxxxxxxxxxxx> wrote:
> > >
> > > > Hello,
> > > > I am having a problem receiving multiple pages
> > > > using hylafax. The logs show that multiple
> > pages
> > > > were transmitted, however the resulting tif that
> > is
> > > > generated only has one page.
> > > >
> > > > Sep 13 11:56:23 fromage FaxGetty[12548]: ANSWER:
> > FAX
> > > > CONNECTION DEVICE '/dev/ttyS1'
> > > > Sep 13 11:56:58 fromage FaxGetty[12548]: RECV
> > FAX
> > > > (000000074): from , page 1 in 0:27, INF, 3.85
> > > > line/mm, 2-D MMR, 9600 bit/s
> > > > Sep 13 11:57:28 fromage FaxGetty[12548]: RECV
> > FAX
> > > > (000000074): from , page 2 in 0:30, INF, 3.85
> > > > line/mm, 2-D MMR, 9600 bit/s
> > > > Sep 13 11:57:28 fromage FaxGetty[12548]: RECV
> > FAX
> > > > (000000074): recvq/fax000000046.tif from , route
> > to
> > > > <unspecified>, 2 pages in 1:05
> > > > Sep 13 11:57:30 fromage FaxGetty[12548]: RECV
> > FAX:
> > > > bin/faxrcvd "recvq/fax000000046.tif" "ttyS1"
> > > > "000000074" "" "" ""
> > > > Sep 13 11:57:42 fromage FaxGetty[12548]: MODEM
> > USR
> > > > 00:00:00/Configuration Profile... Product type
> >
> > > > US/Canada External Options
> > > > HST,V32bis,Terbo,V.FC,V.34 Fax Options
> >
> > > > Class 1/Class 2.0 Clock Freq
> > 20.16Mhz
> > > > Eprom 256k Ram
> >
> > > > 32k Supervisor date 12/02/94 DSP date
> >
> > > > 12/02/94 Supervisor rev 6.0.5 DSP
> > rev
> > > > 1.0.6
> > > >
> > > > And from the xferfaxlog:
> > > > 09/13/04 11:56 RECV 000000074 ttyS1
> >
> > > > "" fax "+1.###.###.####" ""
> >
> > > > 2220056 2 1:05 1:05 "" ""
> > ""
> > > > ""
> > > > (I put #'s over the number)
> > > >
> > > > I am currently using hylafax-4.1.8-1rh3 on
> > RedHat
> > > > Enterprise Linux v3.0
> > > > What could be causing this problem?
> > > > If more information is needed, please tell me
> > what
> > > > and I will post it.
> > > >
> > > > Thanks in advance,
> > > > Justin Rush
> > > > Internet Scout Project
> > > > jrush@xxxxxxxxxxxxxx
> > > >
> > > > ____________________ HylaFAX(tm) Users Mailing
> > List
> > > > _______________________
> > > > To subscribe/unsubscribe, click
> > > > http://lists.hylafax.org/cgi-bin/lsg2.cgi
> > > > On UNIX: mail -s unsubscribe
> > > > hylafax-users-request@xxxxxxxxxxx < /dev/null
> > > > *To learn about commercial HylaFAX(tm)
> > support,
> > > > mail sales@xxxxxxxxx*
> > > >
> > > >
> > >
> > >
> > >
> > >
> > >
> > > __________________________________
> > > Do you Yahoo!?
> > > New and Improved Yahoo! Mail - 100MB free storage!
> > > http://promotions.yahoo.com/new_mail
> >
> > ____________________ HylaFAX(tm) Users Mailing List
> > _______________________
> > To subscribe/unsubscribe, click
> > http://lists.hylafax.org/cgi-bin/lsg2.cgi
> > On UNIX: mail -s unsubscribe
> > hylafax-users-request@xxxxxxxxxxx < /dev/null
> > *To learn about commercial HylaFAX(tm) support,
> > mail sales@xxxxxxxxx*
> >
> >
>
>
>
>
> __________________________________
> Do you Yahoo!?
> Yahoo! Mail is new and improved - Check it out!
> http://promotions.yahoo.com/new_mail
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
> To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
/dev/null
> *To learn about commercial HylaFAX(tm) support, mail
sales@xxxxxxxxx*
____________________ HylaFAX(tm) Users Mailing List
_______________________
To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
/dev/null
*To learn about commercial HylaFAX(tm) support, mail
sales@xxxxxxxxx*
