Re: [hylafax-users] Problem receiving multiple pages

[Justin Rush <jrush@xxxxxxxxxxxxxx>]

from my config file for ttyS1:
--
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use class 1 interface
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       xonxoff         # software flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd:       ATI7            # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow control
Class1SFLOCmd:          ""              # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd:  AT+FRS=1        # wait after sending TCF for response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0
--
The modem is an old USR Courrier modem.  It seems that the modem is receiving the fax properly but the internals of hylafax just aren't handling the fax properly.

Anything else I can check?

Thanks,
Justin


On Mon, Sep 13, 2004 at 11:50:17AM -0700, Pedro Rocadas wrote:
> Did you configured your modem in CLass1? What is the
> value of ModemFlowControl in your config.ttyS1 file?
> if it's not xonxoff try it. Other thing, you are using
> a USR modem so, I definittly recommend you hylafax
> 4.2.0, but if you want a better advice, throw away
> that USR and buy a Multitech or a Zoom modem.
> 
> --- Justin Rush <jrush@xxxxxxxxxxxxxx> wrote:
> 
> > Hello,
> > 	I am having a problem receiving multiple pages
> > using hylafax.  The logs show that multiple pages
> > were transmitted, however the resulting tif that is
> > generated only has one page.
> > 
> > Sep 13 11:56:23 fromage FaxGetty[12548]: ANSWER: FAX
> > CONNECTION  DEVICE '/dev/ttyS1'
> > Sep 13 11:56:58 fromage FaxGetty[12548]: RECV FAX
> > (000000074): from , page 1 in 0:27, INF, 3.85
> > line/mm, 2-D MMR, 9600 bit/s
> > Sep 13 11:57:28 fromage FaxGetty[12548]: RECV FAX
> > (000000074): from , page 2 in 0:30, INF, 3.85
> > line/mm, 2-D MMR, 9600 bit/s
> > Sep 13 11:57:28 fromage FaxGetty[12548]: RECV FAX
> > (000000074): recvq/fax000000046.tif from , route to
> > <unspecified>, 2 pages in 1:05
> > Sep 13 11:57:30 fromage FaxGetty[12548]: RECV FAX:
> > bin/faxrcvd "recvq/fax000000046.tif" "ttyS1"
> > "000000074" "" "" ""
> > Sep 13 11:57:42 fromage FaxGetty[12548]: MODEM USR
> > 00:00:00/Configuration Profile... Product type      
> >     US/Canada External Options               
> > HST,V32bis,Terbo,V.FC,V.34 Fax Options           
> > Class 1/Class 2.0 Clock Freq             20.16Mhz
> > Eprom                  256k Ram                   
> > 32k Supervisor date        12/02/94 DSP date        
> >       12/02/94 Supervisor rev         6.0.5 DSP rev 
> >               1.0.6
> > 
> > And from the xferfaxlog:
> > 09/13/04 11:56  RECV    000000074       ttyS1       
> >    ""      fax     "+1.###.###.####"       ""     
> > 2220056 2       1:05    1:05    ""     ""       ""  
> >    ""
> > (I put #'s over the number)
> > 
> > I am currently using hylafax-4.1.8-1rh3 on RedHat
> > Enterprise Linux v3.0
> > What could be causing this problem?
> > If more information is needed, please tell me what
> > and I will post it.
> > 
> > Thanks in advance,
> > Justin Rush
> > Internet Scout Project
> > jrush@xxxxxxxxxxxxxx
> > 
> > ____________________ HylaFAX(tm) Users Mailing List
> > _______________________
> >   To subscribe/unsubscribe, click
> > http://lists.hylafax.org/cgi-bin/lsg2.cgi
> >  On UNIX: mail -s unsubscribe
> > hylafax-users-request@xxxxxxxxxxx < /dev/null
> >   *To learn about commercial HylaFAX(tm) support,
> > mail sales@xxxxxxxxx*
> > 
> > 
> 
> 
> 
> 	
> 		
> __________________________________
> Do you Yahoo!?
> New and Improved Yahoo! Mail - 100MB free storage!
> http://promotions.yahoo.com/new_mail 

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*