Re: [hylafax-users] Rockwell modem cards in Lucent TNT

To: Lee Howard <faxguy@xxxxxxxxxxxxxxxx>
Subject: Re: [hylafax-users] Rockwell modem cards in Lucent TNT
From: Tracy R Reed <treed@xxxxxxxxxxxxxxxxxxxxx>
Cc: hylafax-users@xxxxxxxxxxx
Date: Tue, 24 Aug 2004 15:43:37 -0700

On Tue, Aug 24, 2004 at 02:40:27PM -0700, Lee Howard spake thusly:
> Add these lines to your modem config file.  It would appear that 
> faxaddmodem was trying to do the right thing, but couldn't due to an 
> awk problem that likely was fixed in 4.2.0.

I have added them. Attached is the latest result.

-- 
Tracy Reed                     The attachment is a digital signature.
http://copilotconsulting.com   More info: http://copilotconsulting.com/sig

Aug 24 15:47:26.23: [10945]: SESSION BEGIN 00011655 16196717023
Aug 24 15:47:26.23: [10945]: HylaFAX (tm) Version 4.1.8
Aug 24 15:47:26.23: [10945]: SEND FAX: JOB 17920 DEST 16196717023 COMMID 00011655 DEVICE '/dev/ttya0'
Aug 24 15:47:26.23: [10945]: MODEM set DTR OFF
Aug 24 15:47:26.23: [10945]: MODEM set baud rate: 0 baud (flow control unchanged)
Aug 24 15:47:26.23: [10945]: DELAY 75 ms
Aug 24 15:47:26.30: [10945]: MODEM set DTR ON
Aug 24 15:47:26.30: [10945]: DELAY 2600 ms
Aug 24 15:47:29.90: [10945]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Aug 24 15:47:29.90: [10945]: DELAY 10 ms
Aug 24 15:47:29.91: [10945]: MODEM flush i/o
Aug 24 15:47:29.91: [10945]: <-- [4:ATZ\r]
Aug 24 15:47:32.22: [10945]: --> [2:OK]
Aug 24 15:47:32.22: [10945]: DELAY 3000 ms
Aug 24 15:47:35.22: [10945]: <-- [5:ATE0\r]
Aug 24 15:47:35.43: [10945]: --> [4:ATE0]
Aug 24 15:47:35.43: [10945]: --> [2:OK]
Aug 24 15:47:35.44: [10945]: <-- [5:ATV1\r]
Aug 24 15:47:35.74: [10945]: --> [2:OK]
Aug 24 15:47:35.74: [10945]: <-- [5:ATQ0\r]
Aug 24 15:47:36.04: [10945]: --> [2:OK]
Aug 24 15:47:36.04: [10945]: <-- [7:ATS0=0\r]
Aug 24 15:47:36.34: [10945]: --> [2:OK]
Aug 24 15:47:36.34: [10945]: <-- [7:ATS8=2\r]
Aug 24 15:47:36.64: [10945]: --> [2:OK]
Aug 24 15:47:36.64: [10945]: <-- [8:ATS7=60\r]
Aug 24 15:47:36.94: [10945]: --> [2:OK]
Aug 24 15:47:36.94: [10945]: <-- [12:AT+FCLASS=1\r]
Aug 24 15:47:37.24: [10945]: --> [2:OK]
Aug 24 15:47:37.24: [10945]: <-- [7:ATL0M1\r]
Aug 24 15:47:37.54: [10945]: --> [2:OK]
Aug 24 15:47:37.54: [10945]: STATE CHANGE: RUNNING -> SENDING
Aug 24 15:47:37.54: [10945]: MODEM input buffering enabled
Aug 24 15:47:37.54: [10945]: <-- [12:AT+FCLASS=1\r]
Aug 24 15:47:37.94: [10945]: --> [2:OK]
Aug 24 15:47:37.94: [10945]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Aug 24 15:47:37.94: [10945]: DIAL 16196717023
Aug 24 15:47:37.94: [10945]: <-- [16:ATDT16196717023\r]
Aug 24 15:47:52.94: [10945]: --> [7:CONNECT]
Aug 24 15:47:52.94: [10945]: MODEM input buffering disabled
Aug 24 15:47:54.15: [10945]: --> HDLC<16:FF C0 04 00 00 6A AA AA 00 01 09 01 00 00 50 DA>
Aug 24 15:47:54.15: [10945]: --> [2:OK]
Aug 24 15:47:54.15: [10945]: REMOTE NSF "00 00 56 55 55 00 80 90 80 00 00 0A"
Aug 24 15:47:54.15: [10945]: NSF remote fax equipment: Brother 
Aug 24 15:47:54.15: [10945]: <-- [9:AT+FRH=3\r]
Aug 24 15:47:54.35: [10945]: --> [7:CONNECT]
Aug 24 15:47:54.85: [10945]: --> HDLC<25:FF C0 02 CC 4C 0C EC 8C EC 6C 9C 8C 6C 8C 04 04 04 04 04 04 04 04 04 26 5B>
Aug 24 15:47:54.85: [10945]: --> [2:OK]
Aug 24 15:47:54.85: [10945]: REMOTE CSI "16196717023"
Aug 24 15:47:54.85: [10945]: <-- [9:AT+FRH=3\r]
Aug 24 15:47:55.05: [10945]: --> [7:CONNECT]
Aug 24 15:47:55.05: [10945]: --> HDLC<11:FF C8 01 00 72 1D 01 01 88 A9 FF>
Aug 24 15:47:55.05: [10945]: --> [2:OK]
Aug 24 15:47:55.05: [10945]: REMOTE best rate 9600 bit/s
Aug 24 15:47:55.05: [10945]: REMOTE max page width 1728 pixels in 215 mm
Aug 24 15:47:55.05: [10945]: REMOTE max unlimited page length
Aug 24 15:47:55.05: [10945]: REMOTE best vres 7.7 line/mm
Aug 24 15:47:55.05: [10945]: REMOTE best format 1-D MR
Aug 24 15:47:55.05: [10945]: REMOTE best 20 ms, 10 ms/scanline
Aug 24 15:47:55.05: [10945]: USE 9600 bit/s
Aug 24 15:47:55.05: [10945]: USE 20 ms, 10 ms/scanline
Aug 24 15:47:55.05: [10945]: SEND file "docq/doc42.tif;30"
Aug 24 15:47:55.05: [10945]: USE page width 1728 pixels in 215 mm
Aug 24 15:47:55.05: [10945]: USE unlimited page length
Aug 24 15:47:55.05: [10945]: USE 3.85 line/mm
Aug 24 15:47:55.05: [10945]: USE 1-D MR
Aug 24 15:47:55.05: [10945]: SEND training at v.29 9600 bit/s
Aug 24 15:47:55.05: [10945]: <-- [9:AT+FTH=3\r]
Aug 24 15:47:55.25: [10945]: --> [7:CONNECT]
Aug 24 15:47:55.25: [10945]: <-- HDLC<23:FF C0 C2 4C CC EC EC EC 4C EC 6C 6C 1C 04 04 04 04 04 04 04 04 04 04>
Aug 24 15:47:55.25: [10945]: <-- data [23]
Aug 24 15:47:55.25: [10945]: <-- data [2]
Aug 24 15:47:57.35: [10945]: --> [7:CONNECT]
Aug 24 15:47:57.35: [10945]: <-- HDLC<6:FF C8 C1 00 60 10>
Aug 24 15:47:57.35: [10945]: <-- data [6]
Aug 24 15:47:57.35: [10945]: <-- data [2]
Aug 24 15:47:57.85: [10945]: --> [2:OK]
Aug 24 15:47:57.85: [10945]: DELAY 70 ms
Aug 24 15:47:57.92: [10945]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 24 15:47:57.92: [10945]: <-- [10:AT+FTM=96\r]
Aug 24 15:47:58.05: [10945]: --> [7:CONNECT]
Aug 24 15:47:58.05: [10945]: <-- data [1024]
Aug 24 15:47:58.05: [10945]: <-- data [776]
Aug 24 15:47:58.05: [10945]: <-- data [2]
Aug 24 15:48:00.05: [10945]: --> [2:OK]
Aug 24 15:48:00.05: [10945]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 24 15:48:00.05: [10945]: <-- [9:AT+FRH=3\r]
Aug 24 15:48:00.75: [10945]: --> [7:CONNECT]
Aug 24 15:48:01.85: [10945]: --> HDLC<5:FF C8 22 67 DD>
Aug 24 15:48:01.85: [10945]: --> [2:OK]
Aug 24 15:48:01.85: [10945]: SEND training at v.29 7200 bit/s
Aug 24 15:48:01.85: [10945]: <-- [9:AT+FTH=3\r]
Aug 24 15:48:02.05: [10945]: --> [7:CONNECT]
Aug 24 15:48:02.05: [10945]: <-- HDLC<23:FF C0 C2 4C CC EC EC EC 4C EC 6C 6C 1C 04 04 04 04 04 04 04 04 04 04>
Aug 24 15:48:02.05: [10945]: <-- data [23]
Aug 24 15:48:02.05: [10945]: <-- data [2]
Aug 24 15:48:03.95: [10945]: --> [7:CONNECT]
Aug 24 15:48:03.95: [10945]: <-- HDLC<6:FF C8 C1 00 70 10>
Aug 24 15:48:03.95: [10945]: <-- data [6]
Aug 24 15:48:03.95: [10945]: <-- data [2]
Aug 24 15:48:04.45: [10945]: --> [2:OK]
Aug 24 15:48:04.45: [10945]: DELAY 70 ms
Aug 24 15:48:04.52: [10945]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 24 15:48:04.52: [10945]: <-- [10:AT+FTM=72\r]
Aug 24 15:48:04.65: [10945]: --> [7:CONNECT]
Aug 24 15:48:04.65: [10945]: <-- data [1024]
Aug 24 15:48:04.65: [10945]: <-- data [326]
Aug 24 15:48:04.65: [10945]: <-- data [2]
Aug 24 15:48:06.65: [10945]: --> [2:OK]
Aug 24 15:48:06.65: [10945]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 24 15:48:06.65: [10945]: <-- [9:AT+FRH=3\r]
Aug 24 15:48:07.35: [10945]: --> [7:CONNECT]
Aug 24 15:48:08.45: [10945]: --> HDLC<5:FF C8 22 67 DD>
Aug 24 15:48:08.45: [10945]: --> [2:OK]
Aug 24 15:48:08.45: [10945]: SEND training at v.27ter 4800 bit/s
Aug 24 15:48:08.45: [10945]: <-- [9:AT+FTH=3\r]
Aug 24 15:48:08.65: [10945]: --> [7:CONNECT]
Aug 24 15:48:08.65: [10945]: <-- HDLC<23:FF C0 C2 4C CC EC EC EC 4C EC 6C 6C 1C 04 04 04 04 04 04 04 04 04 04>
Aug 24 15:48:08.65: [10945]: <-- data [23]
Aug 24 15:48:08.65: [10945]: <-- data [2]
Aug 24 15:48:10.55: [10945]: --> [7:CONNECT]
Aug 24 15:48:10.55: [10945]: <-- HDLC<6:FF C8 C1 00 50 10>
Aug 24 15:48:10.55: [10945]: <-- data [6]
Aug 24 15:48:10.55: [10945]: <-- data [2]
Aug 24 15:48:11.05: [10945]: --> [2:OK]
Aug 24 15:48:11.05: [10945]: DELAY 70 ms
Aug 24 15:48:11.12: [10945]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 24 15:48:11.12: [10945]: <-- [10:AT+FTM=48\r]
Aug 24 15:48:11.35: [10945]: --> [7:CONNECT]
Aug 24 15:48:11.35: [10945]: <-- data [900]
Aug 24 15:48:11.35: [10945]: <-- data [2]
Aug 24 15:48:13.56: [10945]: --> [2:OK]
Aug 24 15:48:13.56: [10945]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 24 15:48:13.56: [10945]: <-- [9:AT+FRH=3\r]
Aug 24 15:48:14.46: [10945]: --> [7:CONNECT]
Aug 24 15:48:15.46: [10945]: --> HDLC<5:FF C8 22 67 DD>
Aug 24 15:48:15.46: [10945]: --> [2:OK]
Aug 24 15:48:15.46: [10945]: SEND training at v.27ter fallback mode 2400 bit/s
Aug 24 15:48:15.46: [10945]: <-- [9:AT+FTH=3\r]
Aug 24 15:48:15.66: [10945]: --> [7:CONNECT]
Aug 24 15:48:15.66: [10945]: <-- HDLC<23:FF C0 C2 4C CC EC EC EC 4C EC 6C 6C 1C 04 04 04 04 04 04 04 04 04 04>
Aug 24 15:48:15.66: [10945]: <-- data [23]
Aug 24 15:48:15.66: [10945]: <-- data [2]
Aug 24 15:48:17.56: [10945]: --> [7:CONNECT]
Aug 24 15:48:17.56: [10945]: <-- HDLC<6:FF C8 C1 00 40 10>
Aug 24 15:48:17.56: [10945]: <-- data [6]
Aug 24 15:48:17.56: [10945]: <-- data [2]
Aug 24 15:48:18.06: [10945]: --> [2:OK]
Aug 24 15:48:18.06: [10945]: DELAY 70 ms
Aug 24 15:48:18.13: [10945]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 24 15:48:18.13: [10945]: <-- [10:AT+FTM=24\r]
Aug 24 15:48:18.36: [10945]: --> [7:CONNECT]
Aug 24 15:48:18.36: [10945]: <-- data [450]
Aug 24 15:48:18.36: [10945]: <-- data [2]
Aug 24 15:48:20.66: [10945]: --> [2:OK]
Aug 24 15:48:20.66: [10945]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 24 15:48:20.66: [10945]: <-- [9:AT+FRH=3\r]
Aug 24 15:48:21.76: [10945]: --> [7:CONNECT]
Aug 24 15:48:22.76: [10945]: --> HDLC<5:FF C8 22 67 DD>
Aug 24 15:48:22.76: [10945]: --> [2:OK]
Aug 24 15:48:22.76: [10945]: TRAINING failed
Aug 24 15:48:22.76: [10945]: <-- [9:AT+FTH=3\r]
Aug 24 15:48:22.96: [10945]: --> [7:CONNECT]
Aug 24 15:48:22.96: [10945]: <-- HDLC<3:FF C8 DF>
Aug 24 15:48:22.96: [10945]: <-- data [3]
Aug 24 15:48:22.96: [10945]: <-- data [2]
Aug 24 15:48:24.36: [10945]: --> [2:OK]
Aug 24 15:48:24.36: [10945]: MODEM input buffering enabled
Aug 24 15:48:24.36: [10945]: SEND FAILED: JOB 17920 DEST 16196717023 ERR Failure to train remote modem at 2400 bps or minimum speed; too many attempts to dial
Aug 24 15:48:24.36: [10945]: <-- [5:ATH0\r]
Aug 24 15:48:26.26: [10945]: --> [2:OK]
Aug 24 15:48:26.26: [10945]: MODEM set DTR OFF
Aug 24 15:48:26.26: [10945]: MODEM set baud rate: 0 baud (flow control unchanged)
Aug 24 15:48:26.26: [10945]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Aug 24 15:48:26.26: [10945]: SESSION END

Attachment: pgp00016.pgp
Description: PGP signature

Follow-Ups:
- Re: [hylafax-users] Rockwell modem cards in Lucent TNT
  - From: Lee Howard

References:
- [hylafax-users] Rockwell modem cards in Lucent TNT
  - From: Tracy R Reed
- Re: [hylafax-users] Rockwell modem cards in Lucent TNT
  - From: Lee Howard
- Re: [hylafax-users] Rockwell modem cards in Lucent TNT
  - From: Tracy R Reed
- Re: [hylafax-users] Rockwell modem cards in Lucent TNT
  - From: Lee Howard
- Re: [hylafax-users] Rockwell modem cards in Lucent TNT
  - From: Tracy R Reed
- Re: [hylafax-users] Rockwell modem cards in Lucent TNT
  - From: Lee Howard

Prev by Date: [hylafax-users] Can't send faxes any longer.
Next by Date: Re: [hylafax-users] Can't send faxes any longer.
Previous by thread: Re: [hylafax-users] Rockwell modem cards in Lucent TNT
Next by thread: Re: [hylafax-users] Rockwell modem cards in Lucent TNT
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services