Re: [hylafax-users] Modem Command Errors

To: Lee Howard <faxguy@xxxxxxxxxxxxxxxx>
Subject: Re: [hylafax-users] Modem Command Errors
From: Horst Simon <hsimon@xxxxxxxxxxxxxxx>
Cc: Horst Simon <hsimon@xxxxxxxxxxxxxxx>, hylafax-users@xxxxxxxxxxx
Date: Tue, 24 Aug 2004 09:49:18 +1000 (EST)

On Aug 24, 2004 12:19 AM, Lee Howard <faxguy@xxxxxxxxxxxxxxxx> wrote:

> I don't know what to make of that garbage (--> [2:  ]) but i suspect 
> that is an indicator of the problem with the sending modem again.  It 
> appears that the Optima 336 has its own set of problems.
> 
> Lee.
> 
I added a senfax.conf with following lines and it could fax to the other
Optima 336 and it still gets errors and falls backup to a speed of 2400:
sendfax.conf:
TypeRules:      /usr/local/lib/fax/typerules
DesiredMst:     20ms
DesiredSpeed:   9600

The log file:
Aug 24 09:34:54.07: [ 4020]: SESSION BEGIN 000000022 61395531624
Aug 24 09:34:54.07: [ 4020]: HylaFAX (tm) Version 4.2.0
Aug 24 09:34:54.07: [ 4020]: SEND FAX: JOB 15 DEST 9553-1624 COMMID
000000022 DEVICE '/dev/ttyS0'
Aug 24 09:34:54.07: [ 4020]: <-- [12:AT+FCLASS=1\r]
Aug 24 09:34:54.21: [ 4020]: --> [2:OK]
Aug 24 09:34:54.22: [ 4020]: DIAL 95531624
Aug 24 09:34:54.22: [ 4020]: <-- [13:ATDT95531624\r]
Aug 24 09:35:38.44: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:40.16: [ 4020]: --> [2:OK]
Aug 24 09:35:40.16: [ 4020]: REMOTE NSF "B5 00 AA 48 79 6C 61 46 41 58
20 28 74 6D 29 20 56 65 72 73 69 6F 6E 20 34 2E 32 2E 30"
Aug 24 09:35:40.16: [ 4020]: NSF remote fax equipment: HylaFAX 
Aug 24 09:35:40.16: [ 4020]: NSF remote station ID: "HylaFAX (tm)
Version 4.2.0"
Aug 24 09:35:40.16: [ 4020]: <-- [9:AT+FRH=3\r]
Aug 24 09:35:40.20: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:40.85: [ 4020]: --> [2:OK]
Aug 24 09:35:40.85: [ 4020]: REMOTE CSI "HSC +61(0)3 95531624"
Aug 24 09:35:40.85: [ 4020]: <-- [9:AT+FRH=3\r]
Aug 24 09:35:40.89: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:41.21: [ 4020]: --> [2:OK]
Aug 24 09:35:41.21: [ 4020]: REMOTE best rate 14400 bit/s
Aug 24 09:35:41.21: [ 4020]: REMOTE max A3 page width (303 mm)
Aug 24 09:35:41.21: [ 4020]: REMOTE max unlimited page length
Aug 24 09:35:41.21: [ 4020]: REMOTE best vres R16 x 15.4 line/mm
Aug 24 09:35:41.21: [ 4020]: REMOTE best format 2-D MMR
Aug 24 09:35:41.21: [ 4020]: REMOTE supports T.30 Annex A, 256-byte ECM
Aug 24 09:35:41.21: [ 4020]: REMOTE best 0 ms/scanline
Aug 24 09:35:41.21: [ 4020]: USE 14400 bit/s
Aug 24 09:35:41.21: [ 4020]: USE error correction mode
Aug 24 09:35:41.21: [ 4020]: USE 0 ms/scanline
Aug 24 09:35:41.21: [ 4020]: SEND file "docq/doc15.ps;c0"
Aug 24 09:35:41.21: [ 4020]: USE A4 page width (215 mm)
Aug 24 09:35:41.21: [ 4020]: USE unlimited page length
Aug 24 09:35:41.21: [ 4020]: USE 3.85 line/mm
Aug 24 09:35:41.21: [ 4020]: USE 2-D MMR
Aug 24 09:35:41.21: [ 4020]: SEND training at v.17 14400 bit/s
Aug 24 09:35:41.21: [ 4020]: <-- [9:AT+FTH=3\r]
Aug 24 09:35:41.34: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:41.34: [ 4020]: <-- data [23]
Aug 24 09:35:41.34: [ 4020]: <-- data [2]
Aug 24 09:35:42.34: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:42.34: [ 4020]: <-- data [7]
Aug 24 09:35:42.34: [ 4020]: <-- data [2]
Aug 24 09:35:43.36: [ 4020]: --> [2:OK]
Aug 24 09:35:43.36: [ 4020]: <-- [9:AT+FTS=7\r]
Aug 24 09:35:43.47: [ 4020]: --> [2:OK]
Aug 24 09:35:43.47: [ 4020]: <-- [11:AT+FTM=145\r]
Aug 24 09:35:43.54: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:43.54: [ 4020]: <-- data [1024]
Aug 24 09:35:45.14: [ 4020]: <-- data [1024]
Aug 24 09:35:45.54: [ 4020]: <-- data [652]
Aug 24 09:35:45.94: [ 4020]: <-- data [2]
Aug 24 09:35:46.46: [ 4020]: --> [2:  ]
Aug 24 09:35:46.46: [ 4020]: Problem sending TCF data
Aug 24 09:35:46.46: [ 4020]: <-- [9:AT+FRH=3\r]
Aug 24 09:35:46.46: [ 4020]: --> [2:OK]
Aug 24 09:35:46.46: [ 4020]: DELAY 1500 ms
Aug 24 09:35:47.96: [ 4020]: SEND training at v.17 12000 bit/s
Aug 24 09:35:47.96: [ 4020]: <-- [9:AT+FTH=3\r]
Aug 24 09:35:47.96: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:47.96: [ 4020]: <-- data [23]
Aug 24 09:35:47.96: [ 4020]: <-- data [2]
Aug 24 09:35:47.97: [ 4020]: --> [2:OK]
Aug 24 09:35:47.97: [ 4020]: Error sending T.30 prologue frames
Aug 24 09:35:47.97: [ 4020]: SEND training at v.17 9600 bit/s
Aug 24 09:35:47.97: [ 4020]: <-- [9:AT+FTH=3\r]
Aug 24 09:35:50.52: [ 4020]: Error sending T.30 prologue frames
Aug 24 09:35:50.52: [ 4020]: SEND training at v.29 9600 bit/s
Aug 24 09:35:50.52: [ 4020]: <-- [9:AT+FTH=3\r]
Aug 24 09:35:50.60: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:50.60: [ 4020]: <-- data [23]
Aug 24 09:35:50.61: [ 4020]: <-- data [2]
Aug 24 09:35:51.60: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:51.60: [ 4020]: <-- data [7]
Aug 24 09:35:51.60: [ 4020]: <-- data [2]
Aug 24 09:35:52.63: [ 4020]: --> [2:OK]
Aug 24 09:35:52.63: [ 4020]: <-- [9:AT+FTS=7\r]
Aug 24 09:35:52.74: [ 4020]: --> [2:OK]
Aug 24 09:35:52.74: [ 4020]: <-- [10:AT+FTM=96\r]
Aug 24 09:35:52.80: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:52.80: [ 4020]: <-- data [1024]
Aug 24 09:35:53.19: [ 4020]: <-- data [776]
Aug 24 09:35:53.70: [ 4020]: <-- data [2]
Aug 24 09:35:54.59: [ 4020]: --> [2:  ]
Aug 24 09:35:54.59: [ 4020]: Problem sending TCF data
Aug 24 09:35:54.59: [ 4020]: <-- [9:AT+FRH=3\r]
Aug 24 09:35:54.59: [ 4020]: --> [2:OK]
Aug 24 09:35:54.59: [ 4020]: DELAY 1500 ms
Aug 24 09:35:56.08: [ 4020]: SEND training at v.29 7200 bit/s
Aug 24 09:35:56.08: [ 4020]: <-- [9:AT+FTH=3\r]
Aug 24 09:35:56.08: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:56.09: [ 4020]: <-- data [23]
Aug 24 09:35:56.09: [ 4020]: <-- data [2]
Aug 24 09:35:56.09: [ 4020]: --> [2:OK]
Aug 24 09:35:56.09: [ 4020]: Error sending T.30 prologue frames
Aug 24 09:35:56.09: [ 4020]: SEND training at v.27ter 4800 bit/s
Aug 24 09:35:56.09: [ 4020]: <-- [9:AT+FTH=3\r]
Aug 24 09:35:58.64: [ 4020]: Error sending T.30 prologue frames
Aug 24 09:35:58.64: [ 4020]: SEND training at v.27ter fallback mode 2400
bit/s
Aug 24 09:35:58.64: [ 4020]: <-- [9:AT+FTH=3\r]
Aug 24 09:35:58.73: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:58.73: [ 4020]: <-- data [23]
Aug 24 09:35:58.73: [ 4020]: <-- data [2]
Aug 24 09:35:59.73: [ 4020]: --> [7:CONNECT]
Aug 24 09:35:59.73: [ 4020]: <-- data [7]
Aug 24 09:35:59.73: [ 4020]: <-- data [2]
Aug 24 09:36:00.75: [ 4020]: --> [2:OK]
Aug 24 09:36:00.75: [ 4020]: <-- [9:AT+FTS=7\r]
Aug 24 09:36:00.86: [ 4020]: --> [2:OK]
Aug 24 09:36:00.86: [ 4020]: <-- [10:AT+FTM=24\r]
Aug 24 09:36:00.97: [ 4020]: --> [7:CONNECT]
Aug 24 09:36:00.97: [ 4020]: <-- data [450]
Aug 24 09:36:00.97: [ 4020]: <-- data [2]
Aug 24 09:36:03.45: [ 4020]: --> [2:OK]
Aug 24 09:36:03.45: [ 4020]: <-- [9:AT+FRH=3\r]
Aug 24 09:36:04.30: [ 4020]: --> [7:CONNECT]
Aug 24 09:36:05.37: [ 4020]: --> [2:OK]
Aug 24 09:36:05.37: [ 4020]: TRAINING succeeded

Regards,
Horst


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] Modem Command Errors
  - From: Lee Howard

References:
- [hylafax-users] Modem Command Errors
  - From: Horst Simon
- Re: [hylafax-users] Modem Command Errors
  - From: Lee Howard
- Re: [hylafax-users] Modem Command Errors
  - From: Horst Simon
- Re: [hylafax-users] Modem Command Errors
  - From: Lee Howard

Prev by Date: [hylafax-users] No Response to PPS repeat 3 times
Next by Date: Re: [hylafax-users] No Response to PPS repeat 3 times
Previous by thread: Re: [hylafax-users] Modem Command Errors
Next by thread: Re: [hylafax-users] Modem Command Errors
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services