|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] beginner problems initializing modem
Hi,
I'm new in hylafax.
I worked my ass through tones of tutorials and can not get hylafax to
work.
I can call my machine an the fax answers.
But sending and receiving does not work.
I tried to send a test fax with the following command I found in a
tutorial:
la | sendfax -n -d 1822
I get the expected answer on the prompt but /var/loga/messages shows up
with the following error:
Jul 8 10:07:08 HylaFax FaxSend[2073]: MODEM MD56XX 57600/
Jul 8 10:07:08 HylaFax FaxSend[2073]: SEND FAX: JOB 2 DEST 1822
COMMID 00000007 DEVICE '/dev/ttyS0'
Jul 8 10:10:15 HylaFax FaxSend[2073]: SEND FAILED: JOB 2 DEST
1822 ERR Unknown problem (check modem power)
Receiving a fax causes the followinf error in /var/log/messages
Jul 8 10:02:19 HylaFax FaxGetty[1961]: /dev/ttyS0: Can not
initialize modem.
Jul 8 10:02:57 HylaFax FaxGetty[1961]: MODEM MD56XX 57600/
Jul 8 10:04:36 HylaFax FaxGetty[1961]: ANSWER: FAX CONNECTION
DEVICE '/dev/ttyS0'
Jul 8 10:05:37 HylaFax FaxGetty[1961]: RECV FAX (00000006):
recvq/fax00004.tif from +49 xxx xxxxxx, route to <unspecified>, 0 pages
in 1:01
Jul 8 10:05:37 HylaFax FaxGetty[1961]: RECV FAX (00000006):
session with +49 xxx xxxxx terminated abnormally: Failure to receive
silence.
Jul 8 10:05:37 HylaFax FaxGetty[1961]: RECV FAX: bin/faxrcvd
"recvq/fax00004.tif" "ttyS0" "00000006" "Failure to receive silence." ""
"" ""
Jul 8 10:05:49 HylaFax FaxGetty[1961]: MODEM MD56XX 57600/
Jul 8 10:06:58 HylaFax FaxGetty[1961]: LOCKWAIT
Can anybody help?
--
maik
PS. My config.ttyS0:
#
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode: 49
AreaCode: 040
FAXNumber: "+49 040 123456"
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: "etc/dialrules"
ServerTracing: 1
SessionTracing: 0xffffffff
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect
fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem
is reset
#ModemAnswerCmd: ATA # use this to answer
phone
#ModemNoFlowCmd: AT&K # disable flow control
cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command
results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook
(hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2
seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received
facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for
transmit
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait
before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait
before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait
before EOP
Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF &
response
Class1SendMsgDelay: 75 # 75ms delay after training
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and
trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training
failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident
frames
Class1TCFMaxNonZero: 10 # max 10% of data may be
non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF
duration
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
