[hylafax-users] Problem send fax (hylafax, mandrake 9.2, whfc)

To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Problem send fax (hylafax, mandrake 9.2, whfc)
From: "zaidie bad" <badzenden@xxxxxxxxxxx>
Date: Wed, 05 May 2004 19:01:36 +0800

m using linux mandrake 9.2 and i have installed this package in my machine

hylafax-4.1.6-3.1.92mdk
hylafax-server-4.1.6-3.1.92mdk
hylafax-client-4.1.6-3mdk
ghostscript-7.07-14mdk
libtiff3-3.5.7-6mdk

the server is running OK.

HylaFAX scheduler on orange.linuxhouse: Running
Modem ttyS0 (60 3 40455307): Running and idle

My problem is i am using WHFC in windows client to sent fax but no page was sent. The status showed it was done and dialled to destination but no page was sent in the transmission

faxstat -d
HylaFAX scheduler on orange.linuxhouse: Running
Modem ttyS0 (60 3 40455307): Waiting for modem to come ready
JID    Pri   S  Owner Number       Pages Dials     TTS Status
114  127 D razida 045752931     0:0   1:12

May 05 17:43:58.32: [ 5338]: SESSION BEGIN 00000096 603045752931 May 05 17:43:58.32: [ 5338]: HylaFAX (tm) Version 4.1.6 May 05 17:43:58.32: [ 5338]: SEND FAX: JOB 114 DEST 045752931 COMMID 00000096 DEVICE '/dev/ttyS0' May 05 17:43:58.32: [ 5338]: DELAY 75 ms May 05 17:43:58.39: [ 5338]: DELAY 2600 ms May 05 17:44:02.00: [ 5338]: DELAY 10 ms May 05 17:44:02.01: [ 5338]: <-- [4:ATZ\r] May 05 17:44:02.16: [ 5338]: --> [2:OK] May 05 17:44:02.16: [ 5338]: DELAY 3000 ms May 05 17:44:05.15: [ 5338]: <-- [5:ATE0\r] May 05 17:44:05.29: [ 5338]: --> [4:ATE0] May 05 17:44:05.29: [ 5338]: --> [2:OK] May 05 17:44:05.29: [ 5338]: <-- [5:ATV1\r] May 05 17:44:05.43: [ 5338]: --> [2:OK] May 05 17:44:05.43: [ 5338]: <-- [7:ATQ0X4\r] May 05 17:44:05.57: [ 5338]: --> [2:OK] May 05 17:44:05.57: [ 5338]: <-- [7:ATS0=0\r] May 05 17:44:05.71: [ 5338]: --> [2:OK] May 05 17:44:05.71: [ 5338]: <-- [7:ATS8=2\r] May 05 17:44:05.85: [ 5338]: --> [2:OK] May 05 17:44:05.85: [ 5338]: <-- [8:ATS7=60\r] May 05 17:44:05.99: [ 5338]: --> [2:OK] May 05 17:44:05.99: [ 5338]: <-- [12:AT&H2&I2&R1\r] May 05 17:44:06.13: [ 5338]: --> [2:OK] May 05 17:44:06.13: [ 5338]: <-- [11:ATS13=1&D2\r] May 05 17:44:06.27: [ 5338]: --> [2:OK] May 05 17:44:06.27: [ 5338]: <-- [6:AT&C1\r] May 05 17:44:06.41: [ 5338]: --> [2:OK] May 05 17:44:06.41: [ 5338]: <-- [12:AT+FCLASS=1\r] May 05 17:44:06.55: [ 5338]: --> [2:OK] May 05 17:44:06.55: [ 5338]: <-- [12:AT+FCLASS=0\r] May 05 17:44:06.69: [ 5338]: --> [2:OK] May 05 17:44:06.69: [ 5338]: <-- [7:ATL0M1\r] May 05 17:44:06.83: [ 5338]: --> [2:OK] May 05 17:44:06.84: [ 5338]: <-- [12:AT+FCLASS=1\r] May 05 17:44:07.07: [ 5338]: --> [2:OK] May 05 17:44:07.08: [ 5338]: DIAL 045752931 May 05 17:44:07.08: [ 5338]: <-- [14:ATDT045752931\r] May 05 17:44:42.49: [ 5338]: --> [7:CONNECT] May 05 17:44:44.24: [ 5338]: --> [2:OK] May 05 17:44:44.24: [ 5338]: REMOTE NSF "00 00 0E 00 00 00 96 0F 01 07 00 10 00 02 95 80 18 01 49 02 50 49 53 43 4F 20 53 45 52 56 49 20 20 20 20 20 03 BA" May 05 17:44:44.24: [ 5338]: NSF remote fax equipment: Panasonic May 05 17:44:44.24: [ 5338]: NSF remote station ID: "PISCO SERVI " May 05 17:44:44.24: [ 5338]: <-- [9:AT+FRH=3\r] May 05 17:44:44.26: [ 5338]: --> [7:CONNECT] May 05 17:44:45.01: [ 5338]: --> [2:OK] May 05 17:44:45.01: [ 5338]: REMOTE CSI "045752931" May 05 17:44:45.01: [ 5338]: <-- [9:AT+FRH=3\r] May 05 17:44:45.03: [ 5338]: --> [7:CONNECT] May 05 17:44:45.38: [ 5338]: --> [2:OK] May 05 17:44:45.38: [ 5338]: REMOTE best rate 9600 bit/s May 05 17:44:45.38: [ 5338]: REMOTE max page width 1728 pixels in 215 mm May 05 17:44:45.38: [ 5338]: REMOTE max unlimited page length May 05 17:44:45.38: [ 5338]: REMOTE best vres 7.7 line/mm May 05 17:44:45.38: [ 5338]: REMOTE best format 2-D MMR May 05 17:44:45.38: [ 5338]: REMOTE supports T.30 Annex A, ECM May 05 17:44:45.38: [ 5338]: REMOTE best 20 ms/scanline May 05 17:44:45.38: [ 5338]: USE 9600 bit/s May 05 17:44:45.38: [ 5338]: USE 20 ms/scanline May 05 17:44:45.38: [ 5338]: <-- [9:AT+FTH=3\r] May 05 17:44:45.58: [ 5338]: --> [7:CONNECT] May 05 17:44:45.58: [ 5338]: <-- data [3] May 05 17:44:45.58: [ 5338]: <-- data [2] May 05 17:44:46.76: [ 5338]: --> [2:OK] May 05 17:44:46.76: [ 5338]: <-- [5:ATH0\r] May 05 17:44:47.00: [ 5338]: --> [2:OK] May 05 17:44:47.00: [ 5338]: SESSION END

have any idea how i can solve this problem?

this my config.ttyS0

CountryCode: 60 AreaCode: 3 FAXNumber: "60 3 40455307" LongDistancePrefix: 1 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0644 LogFileMode: 0644 DeviceMode: 0644 RingsBeforeAnswer: 2 SpeakerVolume: on GettyArgs: "-h %l dx_%s" LocalIdentifier: "NothingSetup" LogFacility: "local5" ClocalAsRoot: yes TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 LockVoiceCalls: yes # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use class 1 interface ModemRate: 19200 # rate for DCE-DTE communication ModemFlowControl: xonxoff # software flow control # ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) ModemNoFlowCmd: AT&H0&I0&R1 # setup modem for no flow control ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control ModemResultCodesCmd: ATQ0X4 # enable result codes # ModemMfrQueryCmd: !USR ModemModelQueryCmd: ATI3 ModemRevQueryCmd: ATI7 # XXX returns a multi-line result # # When AT+FCLASS=1 is issued the modem automatically switches # to software flow control; these parameters let the fax software # reset flow control as needed after entering Class 1. # Class1NFLOCmd: AT&H0&I0&R1 # setup modem for no flow control Class1HFLOCmd: AT&H1&I0&R2 # setup modem for hardware flow control Class1SFLOCmd: "" # modem does this automatically # # This should resolve "DIS/DTC received 3 times" errors: # Class1ResponseWaitCmd: AT+FRS=1 # wait after sending TCF for response # # The remainder of this configuration is included so that the # modem "idles" in Class 0 while not sending or receiving facsimile. # ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0 ModemAnswerCmd: AT+FCLASS=1A # answer in Class 1 # # Disables the reporting of bad frames by the modem. This # overcomes a firmware problem in the x2 and V90 Sportsters. # It is not necessary for the Courier modem. # Class2NRCmd: AT+FNR=1,1,1,0

_________________________________________________________________
Are you in love? Find a date on MSN Personals http://match.msn.com.my/


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

Follow-Ups:
- Re: [hylafax-users] Problem send fax (hylafax, mandrake 9.2, whfc)
  - From: Sebastian Flothow

Prev by Date: [hylafax-users] HylaFax Sending Blank Pages
Next by Date: Re: [hylafax-users] cannot start hylafax
Previous by thread: Re: [hylafax-users] HylaFax Sending Blank Pages
Next by thread: Re: [hylafax-users] Problem send fax (hylafax, mandrake 9.2, whfc)
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services