|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] problems with Multitech Modem MT 2834ZDXb
Those modems NEVER worked right in fax mode.
I have a handful which were purchased with the intent of using them with
Hylafax and they were all pieces of crap; essentially unusable in Class 2
mode. Multitech never helped me even when they were "current product", and
I have as a consequence written them off as a fax modem supplier.
Their "not current product" is a nice line, but the truth is that they
refused to fix the problems even when they WERE current product!
--
--
Karl Denninger (karl@xxxxxxxxxxxxx) Internet Consultant & Kids Rights Activist
http://www.denninger.net Tired of spam at your company? LOOK HERE!
http://childrens-justice.org Working for family and children's rights
http://diversunion.org LOG IN AND GET YOUR TANK STICKERS TODAY!
On Mon, Oct 06, 2003 at 02:01:38PM -0500, Steve Tuckner wrote:
> Milen,
>
> I am sad to inform you that there is no active development on this product
> anymore. You can tinker with the receive sensitivity, and see if it makes
> any difference.
>
> S38 controls the receive sensitivity. Its default is 43 which means -43dbm.
> You could try going to 44 or 45 and see if that helps at all. As you go
> lower (higher numbers), the modem will have trouble distinguishing between
> noise and signal and may not drop carrier when it should.
>
> I would recommend up dating to our MT5634ZBA-V92 if you want to use a modem
> with active fax development on it.
>
> Steve Tuckner
> Multi-Tech Systems
>
> > -----Original Message-----
> > From: hylafax-users-bounce@xxxxxxxxxxx
> > [mailto:hylafax-users-bounce@xxxxxxxxxxx]On Behalf Of Milen Dimitrov
> > Sent: Monday, October 06, 2003 1:40 PM
> > To: hylafax-users@xxxxxxxxxxx
> > Subject: [hylafax-users] problems with Multitech Modem MT 2834ZDXb
> >
> >
> > Hi,
> >
> > I have problems with a multitech modem MT2834ZDXb in receive-only
> > configuration
> > It fails to receive faxes with the one of the following errors:
> >
> > 1. T.30 T2 timeout, expected page not received
> > 2. COMREC error
> > 3. Missing EOL after 5 seconds (section 3.2/T.4)
> >
> > Is there any known poblems with this type of modems?
> > Do I need to change any parameters in modem config file?
> >
> > Thank you for your time and help!
> > Best regards:
> > Milen
> >
> > P.S. I've attached 3 sessions transmitions bellow:
> > ===============================================
> > Log 1
> >
> > The full document was not received because:
> >
> > T.30 T2 timeout, expected page not received
> >
> > ---- Transcript of session follows ----
> >
> > Oct 06 08:00:12.97: [ 2492]: SESSION BEGIN 00000277 14506580077
> > Oct 06 08:00:12.97: [ 2492]: HylaFAX (tm) Version 4.1.7
> > Oct 06 08:00:12.97: [ 2492]: <-- [4:ATA\r]
> > Oct 06 08:00:25.98: [ 2492]: --> [5:+FCON]
> > Oct 06 08:00:25.98: [ 2492]: ANSWER: FAX CONNECTION DEVICE
> > '/dev/ttyS1'
> > Oct 06 08:00:25.98: [ 2492]: RECV FAX: begin
> > Oct 06 08:00:29.68: [ 2492]: --> [21:+FDCS:0,3,0,2,1,0,0,3]
> > Oct 06 08:00:29.68: [ 2492]: REMOTE wants 9600 bit/s
> > Oct 06 08:00:29.68: [ 2492]: REMOTE wants page width 1728
> > pixels in 215
> > mm
> > Oct 06 08:00:29.68: [ 2492]: REMOTE wants unlimited page length
> > Oct 06 08:00:29.68: [ 2492]: REMOTE wants 3.85 line/mm
> > Oct 06 08:00:29.68: [ 2492]: REMOTE wants 2-D MR
> > Oct 06 08:00:29.68: [ 2492]: --> [2:OK]
> > Oct 06 08:00:29.68: [ 2492]: <-- [7:AT+FDR\r]
> > Oct 06 08:00:31.14: [ 2492]: --> [5:+FCFR]
> > Oct 06 08:00:31.14: [ 2492]: --> [21:+FDCS:0,3,0,2,1,0,0,3]
> > Oct 06 08:00:31.14: [ 2492]: REMOTE wants 9600 bit/s
> > Oct 06 08:00:31.14: [ 2492]: REMOTE wants page width 1728
> > pixels in 215
> > mm
> > Oct 06 08:00:31.14: [ 2492]: REMOTE wants unlimited page length
> > Oct 06 08:00:31.14: [ 2492]: REMOTE wants 3.85 line/mm
> > Oct 06 08:00:31.14: [ 2492]: REMOTE wants 2-D MR
> > Oct 06 08:00:31.61: [ 2492]: --> [7:CONNECT]
> > Oct 06 08:00:31.61: [ 2492]: RECV: begin page
> > Oct 06 08:00:31.61: [ 2492]: RECV: send trigger 022
> > Oct 06 08:01:21.38: [ 2492]: RECV: 1100 total lines, 0 bad lines, 1
> > consecutive bad lines
> > Oct 06 08:01:21.38: [ 2492]: --> [15:+FPTS:1,0,0,0,0]
> > Oct 06 08:01:30.35: [ 2492]: --> [8:+FHNG:73]
> > Oct 06 08:01:30.35: [ 2492]: REMOTE HANGUP: T.30 T2 timeout, expected
> > page
> > not received (code 73)
> > Oct 06 08:01:31.00: [ 2492]: --> [2:OK]
> > Oct 06 08:01:31.00: [ 2492]: RECV keeping unconfirmed page
> > Oct 06 08:01:31.00: [ 2492]: RECV FAX (00000277): from , page
> > 1 in 1:02,
> > INF, 3.85 line/mm, 2-D MR, 9600 bit/s
> > Oct 06 08:01:31.00: [ 2492]: RECV FAX (00000277): recvq/fax00127.tif
> > from ,
> > route to <unspecified>, 1 pages in 1:06
> > Oct 06 08:01:31.00: [ 2492]: RECV FAX: T.30 T2 timeout, expected page
> > not
> > received
> > Oct 06 08:01:31.00: [ 2492]: RECV FAX (00000277): session with
> > terminated
> > abnormally: T.30 T2 timeout, expected page not received
> > Oct 06 08:01:31.00: [ 2492]: RECV FAX: bin/faxrcvd
> > "recvq/fax00127.tif"
> > "ttyS1" "00000277" "T.30 T2 timeout, expected page not received" "" ""
> > ======================================================
> > Log 2
> > The full document was not received because:
> >
> > COMREC error
> >
> > ---- Transcript of session follows ----
> >
> > Oct 06 08:43:35.17: [ 2492]: SESSION BEGIN 00000289 14506580077
> > Oct 06 08:43:35.17: [ 2492]: HylaFAX (tm) Version 4.1.7
> > Oct 06 08:43:35.17: [ 2492]: <-- [4:ATA\r]
> > Oct 06 08:43:43.00: [ 2492]: --> [5:+FCON]
> > Oct 06 08:43:43.00: [ 2492]: ANSWER: FAX CONNECTION DEVICE
> > '/dev/ttyS1'
> > Oct 06 08:43:43.00: [ 2492]: RECV FAX: begin
> > Oct 06 08:43:48.73: [ 2492]: --> [28:+FTSI:" 5146379388"]
> > Oct 06 08:43:48.73: [ 2492]: REMOTE TSI "5146379388"
> > Oct 06 08:43:48.73: [ 2492]: --> [21:+FDCS:0,5,0,2,1,0,0,0]
> > Oct 06 08:43:48.73: [ 2492]: REMOTE wants 14400 bit/s
> > Oct 06 08:43:48.73: [ 2492]: REMOTE wants page width 1728
> > pixels in 215
> > mm
> > Oct 06 08:43:48.73: [ 2492]: REMOTE wants unlimited page length
> > Oct 06 08:43:48.73: [ 2492]: REMOTE wants 3.85 line/mm
> > Oct 06 08:43:48.73: [ 2492]: REMOTE wants 2-D MR
> > Oct 06 08:43:48.73: [ 2492]: --> [2:OK]
> > Oct 06 08:43:48.73: [ 2492]: <-- [7:AT+FDR\r]
> > Oct 06 08:43:50.17: [ 2492]: --> [5:+FCFR]
> > Oct 06 08:43:50.17: [ 2492]: --> [28:+FTSI:" 5146379388"]
> > Oct 06 08:43:50.17: [ 2492]: REMOTE TSI "5146379388"
> > Oct 06 08:43:50.17: [ 2492]: --> [21:+FDCS:0,5,0,2,1,0,0,0]
> > Oct 06 08:43:50.17: [ 2492]: REMOTE wants 14400 bit/s
> > Oct 06 08:43:50.17: [ 2492]: REMOTE wants page width 1728
> > pixels in 215
> > mm
> > Oct 06 08:43:50.17: [ 2492]: REMOTE wants unlimited page length
> > Oct 06 08:43:50.17: [ 2492]: REMOTE wants 3.85 line/mm
> > Oct 06 08:43:50.17: [ 2492]: REMOTE wants 2-D MR
> > Oct 06 08:43:50.99: [ 2492]: --> [7:CONNECT]
> > Oct 06 08:43:50.99: [ 2492]: RECV: begin page
> > Oct 06 08:43:50.99: [ 2492]: RECV: send trigger 022
> > Oct 06 08:44:24.51: [ 2492]: RECV: 1126 total lines, 0 bad lines, 1
> > consecutive bad lines
> > Oct 06 08:44:24.51: [ 2492]: --> [15:+FPTS:1,0,0,0,0]
> > Oct 06 08:44:26.18: [ 2492]: --> [8:+FHNG:72]
> > Oct 06 08:44:26.18: [ 2492]: REMOTE HANGUP: COMREC error (code 72)
> > Oct 06 08:44:26.82: [ 2492]: --> [2:OK]
> > Oct 06 08:44:26.82: [ 2492]: RECV keeping unconfirmed page
> > Oct 06 08:44:26.82: [ 2492]: RECV FAX (00000289): from
> > 5146379388, page
> > 1 in
> > 0:38, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
> > Oct 06 08:44:26.82: [ 2492]: RECV FAX (00000289): recvq/fax00139.tif
> > from
> > 5146379388, route to <unspecified>, 1 pages in 0:43
> > Oct 06 08:44:26.82: [ 2492]: RECV FAX: COMREC error
> > Oct 06 08:44:26.82: [ 2492]: RECV FAX (00000289): session with
> > 5146379388
> > terminated abnormally: COMREC error
> > Oct 06 08:44:26.82: [ 2492]: RECV FAX: bin/faxrcvd
> > "recvq/fax00139.tif"
> > "ttyS1" "00000289" "COMREC error" "" ""
> >
> >
> > ===============================================
> > Log 3
> >
> > The full document was not received because:
> >
> > Missing EOL after 5 seconds (section 3.2/T.4)
> >
> > ---- Transcript of session follows ----
> >
> > Oct 06 08:31:24.65: [ 2492]: SESSION BEGIN 00000285 14506580077
> > Oct 06 08:31:24.65: [ 2492]: HylaFAX (tm) Version 4.1.7
> > Oct 06 08:31:24.65: [ 2492]: <-- [4:ATA\r]
> > Oct 06 08:31:33.15: [ 2492]: --> [5:+FCON]
> > Oct 06 08:31:33.15: [ 2492]: ANSWER: FAX CONNECTION DEVICE
> > '/dev/ttyS1'
> > Oct 06 08:31:33.15: [ 2492]: RECV FAX: begin
> > Oct 06 08:31:38.80: [ 2492]: --> [28:+FTSI:" 514 3519806"]
> > Oct 06 08:31:38.80: [ 2492]: REMOTE TSI "514 3519806"
> > Oct 06 08:31:38.80: [ 2492]: --> [21:+FDCS:0,5,0,2,1,0,0,1]
> > Oct 06 08:31:38.80: [ 2492]: REMOTE wants 14400 bit/s
> > Oct 06 08:31:38.80: [ 2492]: REMOTE wants page width 1728
> > pixels in 215
> > mm
> > Oct 06 08:31:38.80: [ 2492]: REMOTE wants unlimited page length
> > Oct 06 08:31:38.80: [ 2492]: REMOTE wants 3.85 line/mm
> > Oct 06 08:31:38.80: [ 2492]: REMOTE wants 2-D MR
> > Oct 06 08:31:38.80: [ 2492]: --> [2:OK]
> > Oct 06 08:31:38.80: [ 2492]: <-- [7:AT+FDR\r]
> > Oct 06 08:31:40.24: [ 2492]: --> [5:+FCFR]
> > Oct 06 08:31:40.24: [ 2492]: --> [28:+FTSI:" 514 3519806"]
> > Oct 06 08:31:40.24: [ 2492]: REMOTE TSI "514 3519806"
> > Oct 06 08:31:40.24: [ 2492]: --> [21:+FDCS:0,5,0,2,1,0,0,1]
> > Oct 06 08:31:40.24: [ 2492]: REMOTE wants 14400 bit/s
> > Oct 06 08:31:40.24: [ 2492]: REMOTE wants page width 1728
> > pixels in 215
> > mm
> > Oct 06 08:31:40.24: [ 2492]: REMOTE wants unlimited page length
> > Oct 06 08:31:40.24: [ 2492]: REMOTE wants 3.85 line/mm
> > Oct 06 08:31:40.24: [ 2492]: REMOTE wants 2-D MR
> > Oct 06 08:31:40.76: [ 2492]: --> [7:CONNECT]
> > Oct 06 08:31:40.76: [ 2492]: RECV: begin page
> > Oct 06 08:31:40.76: [ 2492]: RECV: send trigger 022
> > Oct 06 08:32:14.48: [ 2492]: RECV: 1080 total lines, 0 bad lines, 1
> > consecutive bad lines
> > Oct 06 08:32:15.88: [ 2492]: --> [8:+FHNG:91]
> > Oct 06 08:32:15.88: [ 2492]: REMOTE HANGUP: Missing EOL after
> > 5 seconds
> > (section 3.2/T.4) (code 91)
> > Oct 06 08:32:16.53: [ 2492]: --> [2:OK]
> > Oct 06 08:32:16.53: [ 2492]: RECV keeping unconfirmed page
> > Oct 06 08:32:16.53: [ 2492]: RECV FAX (00000285): from 514
> > 3519806, page
> > 1
> > in 0:38, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
> > Oct 06 08:32:16.53: [ 2492]: RECV FAX (00000285): recvq/fax00135.tif
> > from
> > 514 3519806, route to <unspecified>, 1 pages in 0:43
> > Oct 06 08:32:16.53: [ 2492]: RECV FAX: Missing EOL after 5 seconds
> > (section
> > 3.2/T.4)
> > Oct 06 08:32:16.53: [ 2492]: RECV FAX (00000285): session with 514
> > 3519806
> > terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
> > Oct 06 08:32:16.53: [ 2492]: RECV FAX: bin/faxrcvd
> > "recvq/fax00135.tif"
> > "ttyS1" "00000285" "Missing EOL after 5 seconds (section
> > 3.2/T.4)" "" ""
> >
> >
> >
> >
> > ____________________ HylaFAX(tm) Users Mailing List
> > _______________________
> > To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
> *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
>
> ____________________ HylaFAX(tm) Users Mailing List _______________________
> To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
> *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
>
>
>
> %SPAMBLOCK-SYS: Matched [@hylafax.org], message ok
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*
