|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Multitech MT5634ZPX-PCI config
> -----Original Message-----
> From: hylafax-users-bounce@hylafax.org
> [mailto:hylafax-users-bounce@hylafax.org]On Behalf Of Giulio Orsero
> Sent: dinsdag 29 juli 2003 21:43
> To: hylafax-users@hylafax.org
> Subject: Re: [hylafax-users] Multitech MT5634ZPX-PCI config
>
>
> >Class2 modem goes nicely into running and idle same for class1.
> >Will Class2 solve my 'old' fax problems maybe ?
> Maybe yes; if the problems are due to subtle protocol issues,
> changing class
> may be an option.
>
> If things stay the same, try resetting it to class1, put
> SessionTracing: 0xFFF
> in config.<devid>, restart faxgetty, send a fax, send a log.
>
> --
> giulioo@pobox.com
Back again, this time with a trace.
The modem seems to mess up faxes that get received on class 2, pages look
like random garbage.
on class one normally it works but with some fax machines there seems to be
a problem, i've added the log entry of a failed fax.
Any ideas ?
---- Transcript of session follows ----
Jul 31 16:45:26.51: [17777]: SESSION BEGIN 00000195 4408715750210
Jul 31 16:45:26.52: [17777]: HylaFAX (tm) Version 4.1.6
Jul 31 16:45:26.52: [17777]: MODEM set XON/XOFF/FLUSH: input ignored, output
disabled
Jul 31 16:45:26.52: [17777]: <-- [4:ATA\r]
Jul 31 16:45:32.68: [17777]: --> [7:CONNECT]
Jul 31 16:45:32.68: [17777]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS4'
Jul 31 16:45:32.68: [17777]: STATE CHANGE: ANSWERING -> RECEIVING
Jul 31 16:45:32.68: [17777]: MODEM input buffering enabled
Jul 31 16:45:32.68: [17777]: RECV FAX: begin
Jul 31 16:45:32.73: [17777]: MODEM input buffering disabled
Jul 31 16:45:32.73: [17777]: <-- HDLC<23:FF C0 02 A6 2E 96 B6 96 36 04 E6 76
96 76 A6 26 4E 86 E2 A6 76 F6 E2>
Jul 31 16:45:32.73: [17777]: --> [7:CONNECT]
Jul 31 16:45:32.73: [17777]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Jul 31 16:45:33.95: [17777]: --> [2:OK]
Jul 31 16:45:33.95: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:34.23: [17777]: --> [7:CONNECT]
Jul 31 16:45:35.96: [17777]: --> HDLC<25:FF C0 C2 04 04 04 04 04 04 04 04 D4
1C 4C 0C 0C AC AC 8C 1C 9C 8C 0C F7 EF>
Jul 31 16:45:35.96: [17777]: --> [2:OK]
Jul 31 16:45:35.96: [17777]: REMOTE TSI "01981550028+"
Jul 31 16:45:35.96: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:35.97: [17777]: --> [7:CONNECT]
Jul 31 16:45:36.31: [17777]: --> HDLC<11:FF C8 C1 00 45 05 01 01 00 3A 34>
Jul 31 16:45:36.31: [17777]: --> [2:OK]
Jul 31 16:45:36.31: [17777]: REMOTE wants 14400 bit/s
Jul 31 16:45:36.31: [17777]: REMOTE wants page width 1728 pixels in 215 mm
Jul 31 16:45:36.31: [17777]: REMOTE wants A4 page length (297 mm)
Jul 31 16:45:36.31: [17777]: REMOTE wants 3.85 line/mm
Jul 31 16:45:36.31: [17777]: REMOTE wants 2-D MR
Jul 31 16:45:36.31: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:36.32: [17777]: --> [7:CONNECT]
Jul 31 16:45:36.37: [17777]: --> [10:NO CARRIER]
Jul 31 16:45:36.37: [17777]: RECV training at v.17 14400 bit/s
Jul 31 16:45:36.37: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
generated
Jul 31 16:45:36.37: [17777]: <-- [11:AT+FRM=145\r]
Jul 31 16:45:40.87: [17777]: --> [0:]
Jul 31 16:45:40.87: [17777]: MODEM <Empty line>
Jul 31 16:45:40.87: [17777]: MODEM TIMEOUT: receiving TCF
Jul 31 16:45:40.87: [17777]: --> [2:]
Jul 31 16:45:40.87: [17777]: --> [2:OK]
Jul 31 16:45:40.87: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jul 31 16:45:40.87: [17777]: DELAY 75 ms
Jul 31 16:45:40.95: [17777]: <-- [9:AT+FTH=3\r]
Jul 31 16:45:41.80: [17777]: --> [7:CONNECT]
Jul 31 16:45:41.80: [17777]: <-- HDLC<3:FF C8 22>
Jul 31 16:45:42.13: [17777]: --> [2:OK]
Jul 31 16:45:42.13: [17777]: TRAINING failed
Jul 31 16:45:42.13: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:42.40: [17777]: --> [7:CONNECT]
Jul 31 16:45:44.14: [17777]: --> HDLC<25:FF C0 C2 04 04 04 04 04 04 04 04 D4
1C 4C 0C 0C AC AC 8C 1C 9C 8C 0C F7 EF>
Jul 31 16:45:44.14: [17777]: --> [2:OK]
Jul 31 16:45:44.14: [17777]: REMOTE TSI "01981550028+"
Jul 31 16:45:44.14: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:44.14: [17777]: --> [7:CONNECT]
Jul 31 16:45:44.49: [17777]: --> HDLC<11:FF C8 C1 00 55 05 01 01 00 3E 6E>
Jul 31 16:45:44.49: [17777]: --> [2:OK]
Jul 31 16:45:44.49: [17777]: REMOTE wants 12000 bit/s
Jul 31 16:45:44.49: [17777]: REMOTE wants page width 1728 pixels in 215 mm
Jul 31 16:45:44.49: [17777]: REMOTE wants A4 page length (297 mm)
Jul 31 16:45:44.49: [17777]: REMOTE wants 3.85 line/mm
Jul 31 16:45:44.49: [17777]: REMOTE wants 2-D MR
Jul 31 16:45:44.49: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:44.50: [17777]: --> [7:CONNECT]
Jul 31 16:45:44.55: [17777]: --> [10:NO CARRIER]
Jul 31 16:45:44.55: [17777]: RECV training at v.17 12000 bit/s
Jul 31 16:45:44.55: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
generated
Jul 31 16:45:44.55: [17777]: <-- [11:AT+FRM=121\r]
Jul 31 16:45:49.04: [17777]: --> [0:]
Jul 31 16:45:49.05: [17777]: MODEM <Empty line>
Jul 31 16:45:49.05: [17777]: MODEM TIMEOUT: receiving TCF
Jul 31 16:45:49.05: [17777]: --> [2:]
Jul 31 16:45:49.05: [17777]: --> [2:OK]
Jul 31 16:45:49.05: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jul 31 16:45:49.05: [17777]: DELAY 75 ms
Jul 31 16:45:49.13: [17777]: <-- [9:AT+FTH=3\r]
Jul 31 16:45:49.98: [17777]: --> [7:CONNECT]
Jul 31 16:45:49.98: [17777]: <-- HDLC<3:FF C8 22>
Jul 31 16:45:50.31: [17777]: --> [2:OK]
Jul 31 16:45:50.31: [17777]: TRAINING failed
Jul 31 16:45:50.31: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:50.59: [17777]: --> [7:CONNECT]
Jul 31 16:45:52.32: [17777]: --> HDLC<25:FF C0 C2 04 04 04 04 04 04 04 04 D4
1C 4C 0C 0C AC AC 8C 1C 9C 8C 0C F7 EF>
Jul 31 16:45:52.32: [17777]: --> [2:OK]
Jul 31 16:45:52.32: [17777]: REMOTE TSI "01981550028+"
Jul 31 16:45:52.32: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:52.33: [17777]: --> [7:CONNECT]
Jul 31 16:45:52.68: [17777]: --> HDLC<11:FF C8 C1 00 65 05 01 01 00 32 80>
Jul 31 16:45:52.68: [17777]: --> [2:OK]
Jul 31 16:45:52.68: [17777]: REMOTE wants 9600 bit/s
Jul 31 16:45:52.68: [17777]: REMOTE wants page width 1728 pixels in 215 mm
Jul 31 16:45:52.68: [17777]: REMOTE wants A4 page length (297 mm)
Jul 31 16:45:52.68: [17777]: REMOTE wants 3.85 line/mm
Jul 31 16:45:52.68: [17777]: REMOTE wants 2-D MR
Jul 31 16:45:52.68: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:52.68: [17777]: --> [7:CONNECT]
Jul 31 16:45:52.73: [17777]: --> [10:NO CARRIER]
Jul 31 16:45:52.73: [17777]: RECV training at v.17 9600 bit/s
Jul 31 16:45:52.73: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
generated
Jul 31 16:45:52.73: [17777]: <-- [10:AT+FRM=97\r]
Jul 31 16:45:57.23: [17777]: --> [0:]
Jul 31 16:45:57.23: [17777]: MODEM <Empty line>
Jul 31 16:45:57.23: [17777]: MODEM TIMEOUT: receiving TCF
Jul 31 16:45:57.23: [17777]: --> [2:]
Jul 31 16:45:57.23: [17777]: --> [2:OK]
Jul 31 16:45:57.23: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jul 31 16:45:57.23: [17777]: DELAY 75 ms
Jul 31 16:45:57.31: [17777]: <-- [9:AT+FTH=3\r]
Jul 31 16:45:58.17: [17777]: --> [7:CONNECT]
Jul 31 16:45:58.17: [17777]: <-- HDLC<3:FF C8 22>
Jul 31 16:45:58.49: [17777]: --> [2:OK]
Jul 31 16:45:58.49: [17777]: TRAINING failed
Jul 31 16:45:58.49: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:45:58.76: [17777]: --> [7:CONNECT]
Jul 31 16:46:00.50: [17777]: --> HDLC<25:FF C0 C2 04 04 04 04 04 04 04 04 D4
1C 4C 0C 0C AC AC 8C 1C 9C 8C 0C F7 EF>
Jul 31 16:46:00.50: [17777]: --> [2:OK]
Jul 31 16:46:00.50: [17777]: REMOTE TSI "01981550028+"
Jul 31 16:46:00.50: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:00.51: [17777]: --> [7:CONNECT]
Jul 31 16:46:00.85: [17777]: --> HDLC<11:FF C8 C1 00 75 05 01 01 00 36 DA>
Jul 31 16:46:00.85: [17777]: --> [2:OK]
Jul 31 16:46:00.85: [17777]: REMOTE wants 2400 bit/s
Jul 31 16:46:00.85: [17777]: REMOTE wants page width 1728 pixels in 215 mm
Jul 31 16:46:00.85: [17777]: REMOTE wants A4 page length (297 mm)
Jul 31 16:46:00.85: [17777]: REMOTE wants 3.85 line/mm
Jul 31 16:46:00.85: [17777]: REMOTE wants 2-D MR
Jul 31 16:46:00.85: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:00.86: [17777]: --> [7:CONNECT]
Jul 31 16:46:00.91: [17777]: --> [10:NO CARRIER]
Jul 31 16:46:00.91: [17777]: RECV training at v.17 7200 bit/s
Jul 31 16:46:00.91: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
generated
Jul 31 16:46:00.91: [17777]: <-- [10:AT+FRM=73\r]
Jul 31 16:46:05.40: [17777]: --> [0:]
Jul 31 16:46:05.41: [17777]: MODEM <Empty line>
Jul 31 16:46:05.41: [17777]: MODEM TIMEOUT: receiving TCF
Jul 31 16:46:05.41: [17777]: --> [2:]
Jul 31 16:46:05.41: [17777]: --> [2:OK]
Jul 31 16:46:05.41: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jul 31 16:46:05.41: [17777]: DELAY 75 ms
Jul 31 16:46:05.48: [17777]: <-- [9:AT+FTH=3\r]
Jul 31 16:46:06.34: [17777]: --> [7:CONNECT]
Jul 31 16:46:06.34: [17777]: <-- HDLC<3:FF C8 22>
Jul 31 16:46:06.67: [17777]: --> [2:OK]
Jul 31 16:46:06.67: [17777]: TRAINING failed
Jul 31 16:46:06.67: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:06.94: [17777]: --> [7:CONNECT]
Jul 31 16:46:08.67: [17777]: --> HDLC<25:FF C0 C2 04 04 04 04 04 04 04 04 D4
1C 4C 0C 0C AC AC 8C 1C 9C 8C 0C F7 EF>
Jul 31 16:46:08.68: [17777]: --> [2:OK]
Jul 31 16:46:08.68: [17777]: REMOTE TSI "01981550028+"
Jul 31 16:46:08.68: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:08.68: [17777]: --> [7:CONNECT]
Jul 31 16:46:09.03: [17777]: --> HDLC<11:FF C8 C1 00 51 05 01 01 00 B7 68>
Jul 31 16:46:09.03: [17777]: --> [2:OK]
Jul 31 16:46:09.03: [17777]: REMOTE wants 4800 bit/s
Jul 31 16:46:09.03: [17777]: REMOTE wants page width 1728 pixels in 215 mm
Jul 31 16:46:09.03: [17777]: REMOTE wants A4 page length (297 mm)
Jul 31 16:46:09.03: [17777]: REMOTE wants 3.85 line/mm
Jul 31 16:46:09.03: [17777]: REMOTE wants 2-D MR
Jul 31 16:46:09.03: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:09.04: [17777]: --> [7:CONNECT]
Jul 31 16:46:09.08: [17777]: --> [10:NO CARRIER]
Jul 31 16:46:09.08: [17777]: RECV training at v.27ter 4800 bit/s
Jul 31 16:46:09.08: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
generated
Jul 31 16:46:09.08: [17777]: <-- [10:AT+FRM=48\r]
Jul 31 16:46:10.08: [17777]: --> [8:+FCERROR]
Jul 31 16:46:10.08: [17777]: <-- [10:AT+FRM=48\r]
Jul 31 16:46:13.58: [17777]: --> [0:]
Jul 31 16:46:13.58: [17777]: MODEM <Empty line>
Jul 31 16:46:13.58: [17777]: MODEM TIMEOUT: receiving TCF
Jul 31 16:46:13.58: [17777]: --> [2:]
Jul 31 16:46:13.58: [17777]: --> [2:OK]
Jul 31 16:46:13.59: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jul 31 16:46:13.59: [17777]: DELAY 75 ms
Jul 31 16:46:13.66: [17777]: <-- [9:AT+FTH=3\r]
Jul 31 16:46:14.52: [17777]: --> [7:CONNECT]
Jul 31 16:46:14.52: [17777]: <-- HDLC<3:FF C8 22>
Jul 31 16:46:14.84: [17777]: --> [2:OK]
Jul 31 16:46:14.84: [17777]: TRAINING failed
Jul 31 16:46:14.84: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:15.11: [17777]: --> [7:CONNECT]
Jul 31 16:46:16.84: [17777]: --> HDLC<25:FF C0 C2 04 04 04 04 04 04 04 04 D4
1C 4C 0C 0C AC AC 8C 1C 9C 8C 0C F7 EF>
Jul 31 16:46:16.84: [17777]: --> [2:OK]
Jul 31 16:46:16.84: [17777]: REMOTE TSI "01981550028+"
Jul 31 16:46:16.84: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:16.85: [17777]: --> [7:CONNECT]
Jul 31 16:46:17.19: [17777]: --> HDLC<11:FF C8 C1 00 51 05 01 01 00 B7 68>
Jul 31 16:46:17.19: [17777]: --> [2:OK]
Jul 31 16:46:17.19: [17777]: REMOTE wants 4800 bit/s
Jul 31 16:46:17.19: [17777]: REMOTE wants page width 1728 pixels in 215 mm
Jul 31 16:46:17.19: [17777]: REMOTE wants A4 page length (297 mm)
Jul 31 16:46:17.19: [17777]: REMOTE wants 3.85 line/mm
Jul 31 16:46:17.19: [17777]: REMOTE wants 2-D MR
Jul 31 16:46:17.19: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:17.20: [17777]: --> [7:CONNECT]
Jul 31 16:46:17.25: [17777]: --> [10:NO CARRIER]
Jul 31 16:46:17.25: [17777]: RECV training at v.27ter 4800 bit/s
Jul 31 16:46:17.25: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
generated
Jul 31 16:46:17.25: [17777]: <-- [10:AT+FRM=48\r]
Jul 31 16:46:18.25: [17777]: --> [7:CONNECT]
Jul 31 16:46:19.76: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jul 31 16:46:19.76: [17777]: RECV: TCF 896 bytes, 0% non-zero, 894 zero-run
Jul 31 16:46:19.76: [17777]: --> [10:NO CARRIER]
Jul 31 16:46:19.76: [17777]: DELAY 75 ms
Jul 31 16:46:19.83: [17777]: TRAINING succeeded
Jul 31 16:46:19.84: [17777]: <-- [9:AT+FTH=3\r]
Jul 31 16:46:20.69: [17777]: --> [7:CONNECT]
Jul 31 16:46:20.69: [17777]: <-- HDLC<3:FF C8 21>
Jul 31 16:46:21.02: [17777]: --> [2:OK]
Jul 31 16:46:21.02: [17777]: MODEM input buffering enabled
Jul 31 16:46:21.02: [17777]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Jul 31 16:46:21.02: [17777]: <-- [10:AT+FRM=48\r]
Jul 31 16:46:21.27: [17777]: --> [8:+FCERROR]
Jul 31 16:46:21.27: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jul 31 16:46:21.27: [17777]: MODEM input buffering disabled
Jul 31 16:46:21.27: [17777]: <-- [9:AT+FRH=3\r]
Jul 31 16:46:26.02: [17777]: --> [7:CONNECT]
Jul 31 16:46:26.04: [17777]: --> [10:NO CARRIER]
Jul 31 16:46:26.04: [17777]: MODEM No carrier
Jul 31 16:46:26.04: [17777]: MODEM input buffering enabled
Jul 31 16:46:26.04: [17777]: MODEM set XON/XOFF/FLUSH: input ignored, output
generated
Jul 31 16:46:26.04: [17777]: <-- [10:AT+FRM=48\r]
Jul 31 16:46:33.03: [17777]: MODEM TIMEOUT: reading line from modem
Jul 31 16:46:33.03: [17777]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Jul 31 16:46:33.03: [17777]: MODEM input buffering disabled
Jul 31 16:46:33.03: [17777]: --> [2:]
Jul 31 16:46:33.03: [17777]: --> [2:OK]
Jul 31 16:46:33.04: [17777]: RECV FAX (00000195): recvq/fax00072.tif from
01981550028+, route to <unspecified>, 0 pages in 1:01
Jul 31 16:46:33.04: [17777]: RECV FAX: T.30 T2 timeout, expected page not
received
Jul 31 16:46:33.04: [17777]: <-- [9:AT+FTH=3\r]
Jul 31 16:46:33.89: [17777]: --> [7:CONNECT]
Jul 31 16:46:33.89: [17777]: <-- HDLC<3:FF C8 5F>
Jul 31 16:46:34.22: [17777]: --> [2:OK]
Jul 31 16:46:34.22: [17777]: MODEM input buffering enabled
Jul 31 16:46:34.22: [17777]: RECV FAX (00000195): session with 01981550028+
terminated abnormally: T.30 T2 timeout, expected page not received
Jul 31 16:46:34.22: [17777]: RECV FAX: bin/faxrcvd "recvq/fax00072.tif"
"ttyS4" "00000195" "T.30 T2 timeout, expected page not received" "" ""
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
