Re: [hylafax-users] What's required to make faxpolling work?

To: Peter Christoph Alexander Bär <comet.friend@gmx.net>
Subject: Re: [hylafax-users] What's required to make faxpolling work?
From: Lee Howard <faxguy@howardsilvan.com>
Cc: hylafax-users@hylafax.org
Date: Fri, 4 Jul 2003 09:03:58 -0700

On 2003.07.04 08:04 Peter Christoph Alexander Bär wrote:
> Seems, Class 1 doesn't solve the problem, either, not even with a
> DestControls file.

Class 1 polling works for me...

Lee.

Jul 04 09:00:24.31: [11016]: SESSION BEGIN 00004342 18005264345111
Jul 04 09:00:24.31: [11016]: HylaFAX (tm) Version 4.1.6-rc1
Jul 04 09:00:24.31: [11016]: SEND FAX: JOB 3233 DEST 
18005264345,,,1,,1,,1 COMMID 00004342 DEVICE '/dev/ttyS1'
Jul 04 09:00:24.31: [11016]: STATE CHANGE: RUNNING -> SENDING
Jul 04 09:00:24.31: [11016]: MODEM input buffering enabled
Jul 04 09:00:24.31: [11016]: <-- [12:AT+FCLASS=1\r]
Jul 04 09:00:24.44: [11016]: --> [2:OK]
Jul 04 09:00:24.44: [11016]: MODEM set XON/XOFF/FLUSH: input ignored, 
output disabled
Jul 04 09:00:24.45: [11016]: DIAL 18005264345,,,1,,1,,1
Jul 04 09:00:24.45: [11016]: <-- [26:ATDT18005264345,,,1,,1,,1\r]
Jul 04 09:00:59.05: [11016]: --> [7:CONNECT]
Jul 04 09:00:59.05: [11016]: MODEM input buffering disabled
Jul 04 09:01:00.71: [11016]: --> HDLC<25:FF C0 02 CA 2A 92 04 76 F6 76 
86 C2 04 04 04 04 04 04 04 04 04 04 04 FE 09>
Jul 04 09:01:00.72: [11016]: --> [2:OK]
Jul 04 09:01:00.72: [11016]: REMOTE CSI "Canon ITS"
Jul 04 09:01:00.72: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:01:00.74: [11016]: --> [7:CONNECT]
Jul 04 09:01:01.14: [11016]: --> HDLC<12:FF C8 01 00 B7 1F 23 01 09 28 
2B 9B>
Jul 04 09:01:01.15: [11016]: --> [2:OK]
Jul 04 09:01:01.15: [11016]: Remote has no T.4 receiver capability
Jul 04 09:01:01.15: [11016]: REMOTE best rate 14400 bit/s
Jul 04 09:01:01.15: [11016]: REMOTE max A4 page width (215 mm)
Jul 04 09:01:01.15: [11016]: REMOTE max unlimited page length
Jul 04 09:01:01.15: [11016]: REMOTE best vres 7.7 line/mm
Jul 04 09:01:01.15: [11016]: REMOTE best format 2-D MMR
Jul 04 09:01:01.15: [11016]: REMOTE supports T.30 Annex A, ECM
Jul 04 09:01:01.15: [11016]: REMOTE best 0 ms/scanline
Jul 04 09:01:01.15: [11016]: USE 14400 bit/s
Jul 04 09:01:01.15: [11016]: USE 0 ms/scanline
Jul 04 09:01:01.15: [11016]: STATE CHANGE: SENDING -> RECEIVING
Jul 04 09:01:01.15: [11016]: MODEM input buffering enabled
Jul 04 09:01:01.15: [11016]: POLL FAX: begin (SEP "", PWD "")
Jul 04 09:01:01.19: [11016]: MODEM input buffering disabled
Jul 04 09:01:01.19: [11016]: <-- [9:AT+FTH=3\r]
Jul 04 09:01:02.17: [11016]: --> [7:CONNECT]
Jul 04 09:01:02.17: [11016]: <-- HDLC<23:FF C0 82 0C 6C 8C 1C EC 4C 2C 
0C 6C CC 8C D4 04 04 04 04 04 04 04 04>
Jul 04 09:01:02.17: [11016]: <-- data [23]
Jul 04 09:01:02.17: [11016]: <-- data [2]
Jul 04 09:01:02.20: [11016]: --> [7:CONNECT]
Jul 04 09:01:02.20: [11016]: <-- HDLC<6:FF C8 81 00 77 5E>
Jul 04 09:01:02.20: [11016]: <-- data [6]
Jul 04 09:01:02.20: [11016]: <-- data [2]
Jul 04 09:01:03.36: [11016]: --> [2:OK]
Jul 04 09:01:03.36: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:01:03.51: [11016]: --> [7:CONNECT]
Jul 04 09:01:05.27: [11016]: --> HDLC<25:FF C0 42 CA 2A 92 04 76 F6 76 
86 C2 04 04 04 04 04 04 04 04 04 04 04 E5 7F>
Jul 04 09:01:05.28: [11016]: --> [2:OK]
Jul 04 09:01:05.28: [11016]: REMOTE TSI "Canon ITS"
Jul 04 09:01:05.28: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:01:05.30: [11016]: --> [7:CONNECT]
Jul 04 09:01:05.59: [11016]: --> HDLC<8:FF C8 41 00 47 1E EB 49>
Jul 04 09:01:05.59: [11016]: --> [2:OK]
Jul 04 09:01:05.59: [11016]: REMOTE wants 14400 bit/s
Jul 04 09:01:05.59: [11016]: REMOTE wants A4 page width (215 mm)
Jul 04 09:01:05.59: [11016]: REMOTE wants unlimited page length
Jul 04 09:01:05.59: [11016]: REMOTE wants 7.7 line/mm
Jul 04 09:01:05.59: [11016]: REMOTE wants 2-D MR
Jul 04 09:01:05.59: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:01:05.61: [11016]: --> [7:CONNECT]
Jul 04 09:01:05.65: [11016]: --> [2:]
Jul 04 09:01:05.65: [11016]: --> [10:NO CARRIER]
Jul 04 09:01:05.65: [11016]: RECV training at v.17 14400 bit/s
Jul 04 09:01:05.65: [11016]: MODEM set XON/XOFF/DRAIN: input ignored, 
output generated
Jul 04 09:01:05.65: [11016]: <-- [11:AT+FRM=145\r]
Jul 04 09:01:07.38: [11016]: --> [7:CONNECT]
Jul 04 09:01:08.90: [11016]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jul 04 09:01:08.90: [11016]: RECV: TCF 2720 bytes, 0% non-zero, 2720 
zero-run
Jul 04 09:01:08.90: [11016]: --> [10:NO CARRIER]
Jul 04 09:01:08.90: [11016]: DELAY 75 ms
Jul 04 09:01:08.98: [11016]: TRAINING succeeded
Jul 04 09:01:08.98: [11016]: <-- [9:AT+FTH=3\r]
Jul 04 09:01:09.95: [11016]: --> [7:CONNECT]
Jul 04 09:01:09.95: [11016]: <-- HDLC<3:FF C8 21>
Jul 04 09:01:09.95: [11016]: <-- data [3]
Jul 04 09:01:09.95: [11016]: <-- data [2]
Jul 04 09:01:10.34: [11016]: --> [2:OK]
Jul 04 09:01:10.34: [11016]: MODEM input buffering enabled
Jul 04 09:01:10.34: [11016]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
Jul 04 09:01:10.34: [11016]: <-- [11:AT+FRM=146\r]
Jul 04 09:01:11.26: [11016]: --> [7:CONNECT]
Jul 04 09:01:11.26: [11016]: RECV: begin page
Jul 04 09:01:27.36: [11016]: RECV/CQ: Bad 1D pixel count, row 2201, got 
0, expected 1728
Jul 04 09:01:27.36: [11016]: RECV/CQ: Bad 1D pixel count, row 2202, got 
0, expected 1728
Jul 04 09:01:27.36: [11016]: RECV/CQ: Bad 1D pixel count, row 2203, got 
0, expected 1728
Jul 04 09:01:27.36: [11016]: RECV/CQ: Bad 1D pixel count, row 2204, got 
0, expected 1728
Jul 04 09:01:27.36: [11016]: RECV/CQ: Bad 1D pixel count, row 2205, got 
0, expected 1728
Jul 04 09:01:27.47: [11016]: RECV/CQ: Adjusting for trailing noise (5 
run)
Jul 04 09:01:27.47: [11016]: RECV: 2201 total lines, 0 bad lines, 0 
consecutive bad lines
Jul 04 09:01:27.47: [11016]: RECV: end page
Jul 04 09:01:27.47: [11016]: --> [10:NO CARRIER]
Jul 04 09:01:27.47: [11016]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jul 04 09:01:27.47: [11016]: MODEM input buffering disabled
Jul 04 09:01:27.47: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:01:27.57: [11016]: --> [7:CONNECT]
Jul 04 09:01:28.66: [11016]: --> HDLC<5:FF C8 72 3D 28>
Jul 04 09:01:28.67: [11016]: --> [2:OK]
Jul 04 09:01:28.67: [11016]: RECV recv MPS (more pages, same document)
Jul 04 09:01:28.67: [11016]: <-- [9:AT+FRS=7\r]
Jul 04 09:01:28.84: [11016]: --> [2:OK]
Jul 04 09:01:28.84: [11016]: <-- [9:AT+FTH=3\r]
Jul 04 09:01:29.81: [11016]: --> [7:CONNECT]
Jul 04 09:01:29.81: [11016]: RECV send MCF (message confirmation)
Jul 04 09:01:29.81: [11016]: RECV FAX (00004342): from Canon ITS, page 
1 in 0:21, INF, 7.7 line/mm, 2-D MR, 14400 bit/s
Jul 04 09:01:29.81: [11016]: <-- HDLC<3:FF C8 31>
Jul 04 09:01:29.81: [11016]: <-- data [3]
Jul 04 09:01:29.81: [11016]: <-- data [2]
Jul 04 09:01:30.20: [11016]: --> [2:OK]
Jul 04 09:01:30.20: [11016]: MODEM input buffering enabled
Jul 04 09:01:30.20: [11016]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
Jul 04 09:01:30.20: [11016]: <-- [11:AT+FRM=146\r]
Jul 04 09:01:31.12: [11016]: --> [7:CONNECT]
Jul 04 09:01:31.12: [11016]: RECV: begin page
Jul 04 09:01:48.39: [11016]: RECV/CQ: Bad 1D pixel count, row 2201, got 
0, expected 1728
Jul 04 09:01:48.39: [11016]: RECV/CQ: Bad 1D pixel count, row 2202, got 
0, expected 1728
Jul 04 09:01:48.39: [11016]: RECV/CQ: Bad 1D pixel count, row 2203, got 
0, expected 1728
Jul 04 09:01:48.39: [11016]: RECV/CQ: Bad 1D pixel count, row 2204, got 
0, expected 1728
Jul 04 09:01:48.39: [11016]: RECV/CQ: Bad 1D pixel count, row 2205, got 
0, expected 1728
Jul 04 09:01:48.39: [11016]: RECV/CQ: Adjusting for trailing noise (5 
run)
Jul 04 09:01:48.39: [11016]: RECV: 2201 total lines, 0 bad lines, 0 
consecutive bad lines
Jul 04 09:01:48.39: [11016]: RECV: end page
Jul 04 09:01:48.39: [11016]: --> [10:NO CARRIER]
Jul 04 09:01:48.39: [11016]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jul 04 09:01:48.39: [11016]: MODEM input buffering disabled
Jul 04 09:01:48.39: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:01:48.49: [11016]: --> [7:CONNECT]
Jul 04 09:01:49.58: [11016]: --> HDLC<5:FF C8 72 3D 28>
Jul 04 09:01:49.59: [11016]: --> [2:OK]
Jul 04 09:01:49.59: [11016]: RECV recv MPS (more pages, same document)
Jul 04 09:01:49.59: [11016]: <-- [9:AT+FRS=7\r]
Jul 04 09:01:49.76: [11016]: --> [2:OK]
Jul 04 09:01:49.76: [11016]: <-- [9:AT+FTH=3\r]
Jul 04 09:01:50.73: [11016]: --> [7:CONNECT]
Jul 04 09:01:50.73: [11016]: RECV send MCF (message confirmation)
Jul 04 09:01:50.73: [11016]: RECV FAX (00004342): from Canon ITS, page 
2 in 0:21, INF, 7.7 line/mm, 2-D MR, 14400 bit/s
Jul 04 09:01:50.73: [11016]: <-- HDLC<3:FF C8 31>
Jul 04 09:01:50.73: [11016]: <-- data [3]
Jul 04 09:01:50.73: [11016]: <-- data [2]
Jul 04 09:01:51.12: [11016]: --> [2:OK]
Jul 04 09:01:51.12: [11016]: MODEM input buffering enabled
Jul 04 09:01:51.12: [11016]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
Jul 04 09:01:51.12: [11016]: <-- [11:AT+FRM=146\r]
Jul 04 09:01:52.05: [11016]: --> [7:CONNECT]
Jul 04 09:01:52.05: [11016]: RECV: begin page
Jul 04 09:02:06.94: [11016]: RECV/CQ: Bad 1D pixel count, row 2201, got 
0, expected 1728
Jul 04 09:02:06.94: [11016]: RECV/CQ: Bad 1D pixel count, row 2202, got 
0, expected 1728
Jul 04 09:02:06.94: [11016]: RECV/CQ: Bad 1D pixel count, row 2203, got 
0, expected 1728
Jul 04 09:02:06.94: [11016]: RECV/CQ: Bad 1D pixel count, row 2204, got 
0, expected 1728
Jul 04 09:02:06.94: [11016]: RECV/CQ: Bad 1D pixel count, row 2205, got 
0, expected 1728
Jul 04 09:02:07.05: [11016]: RECV/CQ: Adjusting for trailing noise (5 
run)
Jul 04 09:02:07.05: [11016]: RECV: 2201 total lines, 0 bad lines, 0 
consecutive bad lines
Jul 04 09:02:07.05: [11016]: RECV: end page
Jul 04 09:02:07.05: [11016]: --> [10:NO CARRIER]
Jul 04 09:02:07.05: [11016]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jul 04 09:02:07.05: [11016]: MODEM input buffering disabled
Jul 04 09:02:07.05: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:02:07.15: [11016]: --> [7:CONNECT]
Jul 04 09:02:08.24: [11016]: --> HDLC<5:FF C8 72 3D 28>
Jul 04 09:02:08.25: [11016]: --> [2:OK]
Jul 04 09:02:08.25: [11016]: RECV recv MPS (more pages, same document)
Jul 04 09:02:08.25: [11016]: <-- [9:AT+FRS=7\r]
Jul 04 09:02:08.42: [11016]: --> [2:OK]
Jul 04 09:02:08.42: [11016]: <-- [9:AT+FTH=3\r]
Jul 04 09:02:09.39: [11016]: --> [7:CONNECT]
Jul 04 09:02:09.39: [11016]: RECV send MCF (message confirmation)
Jul 04 09:02:09.39: [11016]: RECV FAX (00004342): from Canon ITS, page 
3 in 0:19, INF, 7.7 line/mm, 2-D MR, 14400 bit/s
Jul 04 09:02:09.39: [11016]: <-- HDLC<3:FF C8 31>
Jul 04 09:02:09.39: [11016]: <-- data [3]
Jul 04 09:02:09.39: [11016]: <-- data [2]
Jul 04 09:02:09.78: [11016]: --> [2:OK]
Jul 04 09:02:09.78: [11016]: MODEM input buffering enabled
Jul 04 09:02:09.78: [11016]: MODEM set XON/XOFF/FLUSH: input ignored, 
output generated
Jul 04 09:02:09.78: [11016]: <-- [11:AT+FRM=146\r]
Jul 04 09:02:10.70: [11016]: --> [7:CONNECT]
Jul 04 09:02:10.70: [11016]: RECV: begin page
Jul 04 09:02:16.48: [11016]: RECV/CQ: Bad 1D pixel count, row 2201, got 
0, expected 1728
Jul 04 09:02:16.48: [11016]: RECV/CQ: Bad 1D pixel count, row 2202, got 
0, expected 1728
Jul 04 09:02:16.48: [11016]: RECV/CQ: Bad 1D pixel count, row 2203, got 
0, expected 1728
Jul 04 09:02:16.48: [11016]: RECV/CQ: Bad 1D pixel count, row 2204, got 
0, expected 1728
Jul 04 09:02:16.48: [11016]: RECV/CQ: Bad 1D pixel count, row 2205, got 
0, expected 1728
Jul 04 09:02:16.48: [11016]: RECV/CQ: Adjusting for trailing noise (5 
run)
Jul 04 09:02:16.48: [11016]: RECV: 2201 total lines, 0 bad lines, 0 
consecutive bad lines
Jul 04 09:02:16.48: [11016]: RECV: end page
Jul 04 09:02:16.59: [11016]: --> [10:NO CARRIER]
Jul 04 09:02:16.59: [11016]: MODEM set XON/XOFF/DRAIN: input ignored, 
output disabled
Jul 04 09:02:16.59: [11016]: MODEM input buffering disabled
Jul 04 09:02:16.59: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:02:16.72: [11016]: --> [7:CONNECT]
Jul 04 09:02:17.77: [11016]: --> HDLC<5:FF C8 74 5D EE>
Jul 04 09:02:17.78: [11016]: --> [2:OK]
Jul 04 09:02:17.78: [11016]: RECV recv EOP (no more pages or documents)
Jul 04 09:02:17.78: [11016]: <-- [9:AT+FRS=7\r]
Jul 04 09:02:17.95: [11016]: --> [2:OK]
Jul 04 09:02:17.95: [11016]: <-- [9:AT+FTH=3\r]
Jul 04 09:02:18.92: [11016]: --> [7:CONNECT]
Jul 04 09:02:18.92: [11016]: <-- HDLC<3:FF C8 31>
Jul 04 09:02:18.92: [11016]: <-- data [3]
Jul 04 09:02:18.92: [11016]: <-- data [2]
Jul 04 09:02:19.31: [11016]: --> [2:OK]
Jul 04 09:02:19.31: [11016]: RECV send MCF (message confirmation)
Jul 04 09:02:19.31: [11016]: RECV FAX (00004342): from Canon ITS, page 
4 in 0:10, INF, 7.7 line/mm, 2-D MR, 14400 bit/s
Jul 04 09:02:19.31: [11016]: RECV FAX (00004342): recvq/fax00256.tif 
from Canon ITS, route to <unspecified>, 4 pages in 1:18
Jul 04 09:02:19.31: [11016]: <-- [9:AT+FRH=3\r]
Jul 04 09:02:19.43: [11016]: --> [7:CONNECT]
Jul 04 09:02:20.65: [11016]: --> HDLC<5:FF C8 5F C8 E7>
Jul 04 09:02:20.65: [11016]: --> [2:OK]
Jul 04 09:02:20.65: [11016]: MODEM input buffering enabled
Jul 04 09:02:20.65: [11016]: POLL FAX: end
Jul 04 09:02:20.66: [11016]: RECV POLL: bin/pollrcvd 
"lee@bilbo.x101.com" "recvq/fax00256.tif" "ttyS1" "00004342" ""
Jul 04 09:02:30.33: [11016]: <-- [9:AT+FTH=3\r]
Jul 04 09:02:31.40: [11016]: --> [7:CONNECT]
Jul 04 09:02:31.40: [11016]: <-- HDLC<3:FF C8 DF>
Jul 04 09:02:31.40: [11016]: <-- data [3]
Jul 04 09:02:31.40: [11016]: <-- data [2]
Jul 04 09:02:31.90: [11016]: --> [2:OK]
Jul 04 09:02:31.90: [11016]: MODEM input buffering enabled
Jul 04 09:02:31.90: [11016]: <-- [5:ATH0\r]
Jul 04 09:02:32.08: [11016]: --> [2:OK]
Jul 04 09:02:32.08: [11016]: MODEM set DTR OFF
Jul 04 09:02:32.08: [11016]: STATE CHANGE: RECEIVING -> MODEMWAIT 
(timeout 5)
Jul 04 09:02:32.08: [11016]: SESSION END

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*

Follow-Ups:
- Re: [hylafax-users] What's required to make faxpolling work?
  - From: Aidan Van Dyk

References:
- [hylafax-users] What's required to make faxpolling work?
  - From: Peter Christoph Alexander Bär
- Re: [hylafax-users] What's required to make faxpolling work?
  - From: Peter Christoph Alexander Bär
- Re: [hylafax-users] What's required to make faxpolling work?
  - From: Lee Howard
- Re: [hylafax-users] What's required to make faxpolling work?
  - From: Peter Christoph Alexander Bär
- Re: [hylafax-users] What's required to make faxpolling work?
  - From: Peter Christoph Alexander Bär

Prev by Date: Re: [hylafax-users] DAD
Next by Date: Re: [hylafax-users] What's required to make faxpolling work?
Previous by thread: Re: [hylafax-users] What's required to make faxpolling work?
Next by thread: Re: [hylafax-users] What's required to make faxpolling work?
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services