Re: [hylafax-users] FW: Setting Inbound Capabilities on aper/senderBasis?

[Bill Binko <bill-sender-4b2fd6@binko.net>]

Hi, Steve
	Here's a representative log (Fax Nums changed to 11111111111
(receive fax) and 12222222222 (sending fax).  We really see this mainly
with the one particular remote site.  We do get high speed
transmissions, and 2-D MR from many other sites without issue.  I
suppose the short answer to your question is: "+FHS:A0".  We sometimes
get a subset of the pages, and very often, we get the full fax.  

	Right now we have 270 faxes from this machine.  Speed breaks
down as (using grep/cut/shell so forgive any counting errors):

     63  14400 
     11  21600 
    189  24000 
      7  26400 
      1  7200 

	
	210 have been received completely (with 60 having errors).  All
errors are +FHS:A0 type.

Bill


LOG:

Jun 06 16:13:45.14: [26814]: SESSION BEGIN 00001415 11111111111 
Jun 06 16:13:45.14: [26814]: HylaFAX (tm) Version 4.1.5 
Jun 06 16:13:45.14: [26814]: <-- [20:AT+FCC=,,,,1,,,,0;A\r] 
Jun 06 16:13:57.93: [26814]: --> [4:+FCO] 
Jun 06 16:13:57.93: [26814]: ANSWER: FAX CONNECTION  DEVICE
'/dev/faxmodem2' 
Jun 06 16:13:57.93: [26814]: RECV FAX: begin
Jun 06 16:13:57.93: [26814]: --> [27:+FTI:"         12222222222"]
Jun 06 16:13:57.93: [26814]: REMOTE TSI "12222222222"
Jun 06 16:13:57.93: [26814]: --> [22:+FCS:0,9,0,2,1,1,0,0,0] 
Jun 06 16:13:57.93: [26814]: REMOTE wants 24000 bit/s 
Jun 06 16:13:57.93: [26814]: REMOTE wants page width 1728 pixels in 215
mm 
Jun 06 16:13:57.93: [26814]: REMOTE wants unlimited page length 
Jun 06 16:13:57.93: [26814]: REMOTE wants 3.85 line/mm 
Jun 06 16:13:57.93: [26814]: REMOTE wants 2-D MR 
Jun 06 16:13:57.93: [26814]: REMOTE wants T.30 Annex A, ECM 
Jun 06 16:13:57.93: [26814]: --> [2:OK] 
Jun 06 16:13:57.93: [26814]: <-- [7:AT+FDR\r] 
Jun 06 16:13:58.72: [26814]: --> [7:CONNECT] 
Jun 06 16:13:58.72: [26814]: RECV: begin page 
Jun 06 16:13:58.72: [26814]: RECV: send trigger 022 
Jun 06 16:13:58.72: [26814]: <-- data [1] 
Jun 06 16:14:11.49: [26814]: RECV: 1088 total lines, 0 bad lines, 0
consecutive bad lines 
Jun 06 16:14:15.44: [26814]: --> [7:+FHS:A0] 
Jun 06 16:14:15.44: [26814]: REMOTE HANGUP: Unspecified Phase D error
(code A0) 
Jun 06 16:14:15.44: [26814]: --> [2:OK] 
Jun 06 16:14:15.44: [26814]: RECV FAX (00001415): recvq/fax01051.tif
from 12222222222, route to <unspecified>, 0 pages in 0:18 
Jun 06 16:14:15.44: [26814]: RECV FAX: Unspecified Phase D error 
Jun 06 16:14:15.44: [26814]: RECV FAX (00001415): session with
12222222222 terminated abnormally: Unspecified Phase D error 
Jun 06 16:14:15.44: [26814]: RECV FAX: bin/faxrcvd "recvq/fax01051.tif"
"faxmodem2" "00001415" "Unspecified Phase D error" "" "" 
Jun 06 16:14:15.74: [26814]: RECV FAX: end 
Jun 06 16:14:15.74: [26814]: SESSION END

-----Original Message-----
From: hylafax-users-bounce@hylafax.org
[mailto:hylafax-users-bounce@hylafax.org] On Behalf Of Steve Tuckner
Sent: Monday, June 09, 2003 4:34 PM
To: hylafax-users@hylafax.org
Subject: [hylafax-users] FW: Setting Inbound Capabilities on a
per/senderBasis?


What exact errors are you receiving and what is it you want to
constrain? -----Original Message-----
From: hylafax-users-bounce@hylafax.org
[mailto:hylafax-users-bounce@hylafax.org]On Behalf Of Bill Binko
Sent: Monday, June 09, 2003 3:16 PM
To: hylafax-users@hylafax.org
Subject: [hylafax-users] Setting Inbound Capabilities on a per/sender
Basis?


Hi everyone.

I am getting a high number of errors from a particular calling machine.
The errors are "Unspecified Phase D" errors, and I am aware that they
will probably be fixed in the upcoming MultiTech firmware release.
However, I am ONLY seeing these when talking to a particular (Panasonic)
Group 3 fax machine.

I would like to setup Hylafax to only reduce its capabilities when this
particular TSI (or CID) number is seen.  Is that possible?  I see how to
do it for sending (through the info directory).  How can I make this
work for inbounds?

Thanks
Bill 

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*