|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Error parsing "+FRM" ?????
there is a bug in the USR firmware >
you need to add the patch at
http://bugs.hylafax.org/bugzilla/show_bug.cgi?id=378 and recompile
_
_______________________________________________________________________________________________
"Seok See Wai
(Rachel)" To: <hylafax-users@hylafax.org>
<rachelcy@hotmail.com> cc:
Sent by: Subject: [hylafax-users] Error parsing "+FRM" ?????
hylafax-users-bounce@h
ylafax.org
04/25/2003 12:55 AM
Hi, need help urgently...
I'm using hylafax-4.1.5-1rh8 on redhat 8, below is my config.ttyS0:
CountryCode: 6
AreaCode: 03
FAXNumber: +92749062
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
#ServerTracing: 1
ServerTracing: 0xFFF
#ServerTracing: 1+2+3
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
AdaptiveAnswer: yes
AnswerRotary: "fax"
ModemType: Class1 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: xonxoff # default
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
ModemDialCmd: ATDT%s # T for tone dialing
ModemAnswerCmd: AT+FCLASS=1;A # default is to answer as fax
ModemSoftResetCmd: ATZ # do soft reset of modem
ModemSoftResetCmdDelay: 300 # pause after soft reset
ModemDTRDropDelay: 50
and my class1 file:
ModemType: Class1 # use this to supply a hint
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
Class1SendMsgDelay: 75 # 75ms delay after training
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training
failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
I was testing it usng a normal call-in, when i hear the fax tone, i
assuming it works,
but after a few times (say bout 3-5 times) calling to the hylafax, my modem
couldn't initialise
again, and the /var/log/messages file showing some entry like below:
Jan 1 19:51:02 fileserver FaxGetty[2869]: MODEM ROCKWELL RC288DPi/EM3900
External Modem Patch 9-11 NVM + SIN + MALY + THAI
Jan 1 19:51:02 fileserver FaxGetty[2869]: <-- [5:ATM0\r]
Jan 1 19:51:02 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:02 fileserver FaxGetty[2869]: STATE CHANGE: RECEIVING ->
RUNNING (timeout 30)
Jan 1 19:51:02 fileserver FaxGetty[2869]: MODEM input buffering disabled
Jan 1 19:51:06 fileserver FaxGetty[2869]: STATE CHANGE: RUNNING ->
LISTENING
Jan 1 19:51:06 fileserver FaxGetty[2869]: MODEM input buffering enabled
Jan 1 19:51:06 fileserver FaxGetty[2869]: --> [4:RING]
Jan 1 19:51:06 fileserver FaxGetty[2869]: STATE CHANGE: LISTENING ->
ANSWERING
Jan 1 19:51:06 fileserver FaxGetty[2869]: MODEM input buffering enabled
Jan 1 19:51:13 fileserver FaxGetty[2869]: ANSWER: FAX CONNECTION DEVICE
'/dev/ttyS0'
Jan 1 19:51:52 fileserver FaxGetty[2869]: RECV FAX (00000061): from 603
2273 5158, page 1 in 0:32, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Jan 1 19:51:52 fileserver FaxGetty[2869]: RECV FAX (00000061):
recvq/fax00060.tif from 603 2273 5158, route to <unspecified>, 1 pages in
0:39
Jan 1 19:51:53 fileserver FaxGetty[2869]: RECV FAX: bin/faxrcvd
"recvq/fax00060.tif" "ttyS0" "00000061" "" "" ""
Jan 1 19:51:54 fileserver FaxGetty[2869]: <-- [5:ATH0\r]
Jan 1 19:51:55 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR OFF
Jan 1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR OFF
Jan 1 19:51:55 fileserver FaxGetty[2869]: DELAY 50 ms
Jan 1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR ON
Jan 1 19:51:55 fileserver FaxGetty[2869]: DELAY 2600 ms
Jan 1 19:51:58 fileserver FaxGetty[2869]: MODEM set baud rate: 19200 baud,
input flow XON/XOFF, output flow XON/XOFF
Jan 1 19:51:58 fileserver FaxGetty[2869]: DELAY 10 ms
Jan 1 19:51:58 fileserver FaxGetty[2869]: MODEM flush i/o
Jan 1 19:51:58 fileserver FaxGetty[2869]: <-- [4:ATZ\r]
Jan 1 19:51:58 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:58 fileserver FaxGetty[2869]: DELAY 300 ms
Jan 1 19:51:58 fileserver FaxGetty[2869]: <-- [5:ATE0\r]
Jan 1 19:51:58 fileserver FaxGetty[2869]: --> [4:ATE0]
Jan 1 19:51:58 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:58 fileserver FaxGetty[2869]: <-- [5:ATV1\r]
Jan 1 19:51:58 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:58 fileserver FaxGetty[2869]: <-- [5:ATQ0\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [7:ATS0=0\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [7:ATS8=2\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [8:ATS7=60\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [6:AT&K4\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [6:AT&D2\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [6:AT&C1\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [12:AT+FCLASS=?\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [14:0,1,1.0,2,8,10]
Jan 1 19:51:59 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Data"
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class 1"
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class 2"
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class 1.0"
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Voice"
Jan 1 19:51:59 fileserver FaxGetty[2869]: <-- [12:AT+FCLASS=1\r]
Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM: Mfr Rockwell
Jan 1 19:52:00 fileserver FaxGetty[2869]: <-- [5:ATI3\r]
Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [21:EM3900 External Modem]
Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [34:Patch 9-11 NVM + SIN +
MALY + THAI]
Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM: Model RC288DPi
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM: Revision EM3900 External
Modem Patch 9-11 NVM + SIN + MALY + THAI
Jan 1 19:52:00 fileserver FaxGetty[2869]: <-- [9:AT+FTM=?\r]
Jan 1 19:52:00 fileserver FaxGetty[2869]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 3.85 line/mm
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 7.7 line/mm
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 2400 bit/s
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 4800 bit/s
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 7200 bit/s
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 9600 bit/s
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 12000 bit/s
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 14400 bit/s
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports page width 1728
pixels in 215 mm
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports page width 2048
pixels in 255 mm
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports page width 2432
pixels in 303 mm
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports A4 page length
(297 mm)
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports B4 page length
(364 mm)
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports unlimited page
length
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 1-D MR
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 2-D MR
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 0 ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 5 ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 10 ms, 5
ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 10 ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 20 ms, 10
ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 20 ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 40 ms, 20
ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports 40 ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]: <-- [9:AT+FRM=?\r]
Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [4:RING]
Jan 1 19:52:00 fileserver FaxGetty[2869]: Error parsing "+FRM" query
response: "OK"
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM set DTR OFF
Jan 1 19:52:00 fileserver FaxGetty[2869]: /dev/ttyS0: Can not initialize
modem.
Jan 1 19:52:00 fileserver FaxGetty[2869]: STATE CHANGE: RECEIVING ->
MODEMWAIT (timeout 30)
Please help!!!
Rachel Seok
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
