|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Error parsing "+FRM" ?????
Hi, need help urgently...
I'm using hylafax-4.1.5-1rh8 on redhat 8, below is
my config.ttyS0:
CountryCode: 6
AreaCode:
03
FAXNumber: +92749062
LongDistancePrefix:
1
InternationalPrefix: 011
DialStringRules:
etc/dialrules
#ServerTracing: 1
ServerTracing:
0xFFF
#ServerTracing:
1+2+3
SessionTracing: 11
RecvFileMode:
0600
LogFileMode: 0600
DeviceMode:
0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h
%l dx_%s"
LocalIdentifier:
"NothingSetup"
TagLineFont:
etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of
%%T"
MaxRecvPages: 25
AdaptiveAnswer:
yes
AnswerRotary: "fax"
ModemType: Class1 # use
this to supply a hint
ModemRate: 19200 # rate for DCE-DTE
communication
ModemFlowControl: xonxoff #
default
ModemNoFlowCmd:
AT&K0 # setup no flow
control
ModemHardFlowCmd:
AT&K3 # setup hardware flow
control
ModemSoftFlowCmd:
AT&K4 # setup software flow
control
ModemSetupDTRCmd:
AT&D2 # setup so DTR drop resets
modem
ModemSetupDCDCmd:
AT&C1 # setup so DCD reflects
carrier (or not)
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd:
!RC288DPi
ModemRevQueryCmd: ATI3 # product
information
ModemDialCmd: ATDT%s # T for
tone dialing
ModemAnswerCmd:
AT+FCLASS=1;A # default is to answer
as fax
ModemSoftResetCmd:
ATZ # do
soft reset of modem
ModemSoftResetCmdDelay: 300 # pause
after soft reset
ModemDTRDropDelay: 50
and my class1 file:
ModemType: Class1 # use this to supply
a hint
Class1Cmd: AT+FCLASS=1 # command to enter class
1
Class1PPMWaitCmd: AT+FTS=7 # command to stop
and wait before PPM
Class1TCFWaitCmd: AT+FTS=7
# command to stop and wait before TCF
Class1EOPWaitCmd:
AT+FTS=9 # command to stop and wait before
EOP
Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before
image
Class1TCFResponseDelay: 75 # 75ms delay
between recv TCF & response
Class1SendMsgDelay:
75 # 75ms delay after training
Class1SwitchingCmd:
AT+FRS=7 # silence between HDLC recv and
trans
Class1TrainingRecovery:
1500 # 1.5sec
delay after training failure
Class1RecvAbortOK: 200 #
wait 200ms for abort response
Class1FrameOverhead: 4
# 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:
40000 # 35+5secs
waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10%
of data may be non-zero
Class1TCFMinRun: 1000 #
min run is 2/3rds of TCF duration
I was testing it usng a normal call-in, when i hear
the fax tone, i assuming it works,
but after a few times (say bout 3-5 times) calling
to the hylafax, my modem couldn't initialise
again, and the /var/log/messages file showing
some entry like below:
Jan 1 19:51:02 fileserver FaxGetty[2869]:
MODEM ROCKWELL RC288DPi/EM3900 External Modem Patch 9-11 NVM + SIN + MALY +
THAI
Jan 1 19:51:02 fileserver FaxGetty[2869]: <--
[5:ATM0\r]
Jan 1 19:51:02 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:02 fileserver FaxGetty[2869]: STATE CHANGE:
RECEIVING -> RUNNING (timeout 30)
Jan 1 19:51:02 fileserver
FaxGetty[2869]: MODEM input buffering disabled
Jan 1 19:51:06
fileserver FaxGetty[2869]: STATE CHANGE: RUNNING -> LISTENING
Jan 1
19:51:06 fileserver FaxGetty[2869]: MODEM input buffering enabled
Jan 1
19:51:06 fileserver FaxGetty[2869]: --> [4:RING]
Jan 1 19:51:06
fileserver FaxGetty[2869]: STATE CHANGE: LISTENING -> ANSWERING
Jan
1 19:51:06 fileserver FaxGetty[2869]: MODEM input buffering enabled
Jan
1 19:51:13 fileserver FaxGetty[2869]: ANSWER: FAX CONNECTION DEVICE
'/dev/ttyS0'
Jan 1 19:51:52 fileserver FaxGetty[2869]: RECV FAX
(00000061): from 603 2273 5158, page 1 in 0:32, INF, 3.85 line/mm, 2-D
MR, 9600 bit/s
Jan 1 19:51:52 fileserver FaxGetty[2869]: RECV FAX
(00000061): recvq/fax00060.tif from 603 2273 5158, route to
<unspecified>, 1 pages in 0:39
Jan 1 19:51:53 fileserver
FaxGetty[2869]: RECV FAX: bin/faxrcvd "recvq/fax00060.tif" "ttyS0" "00000061" ""
"" ""
Jan 1 19:51:54 fileserver FaxGetty[2869]: <--
[5:ATH0\r]
Jan 1 19:51:55 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR
OFF
Jan 1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR
OFF
Jan 1 19:51:55 fileserver FaxGetty[2869]: DELAY 50 ms
Jan
1 19:51:55 fileserver FaxGetty[2869]: MODEM set DTR ON
Jan 1 19:51:55
fileserver FaxGetty[2869]: DELAY 2600 ms
Jan 1 19:51:58 fileserver
FaxGetty[2869]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output
flow XON/XOFF
Jan 1 19:51:58 fileserver FaxGetty[2869]: DELAY 10
ms
Jan 1 19:51:58 fileserver FaxGetty[2869]: MODEM flush
i/o
Jan 1 19:51:58 fileserver FaxGetty[2869]: <--
[4:ATZ\r]
Jan 1 19:51:58 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:58 fileserver FaxGetty[2869]: DELAY 300
ms
Jan 1 19:51:58 fileserver FaxGetty[2869]: <--
[5:ATE0\r]
Jan 1 19:51:58 fileserver FaxGetty[2869]: -->
[4:ATE0]
Jan 1 19:51:58 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:58 fileserver FaxGetty[2869]: <--
[5:ATV1\r]
Jan 1 19:51:58 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:58 fileserver FaxGetty[2869]: <--
[5:ATQ0\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <--
[7:ATS0=0\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <--
[7:ATS8=2\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <--
[8:ATS7=60\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <--
[6:AT&K4\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]:
--> [2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <--
[6:AT&D2\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <--
[6:AT&C1\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: <--
[12:AT+FCLASS=?\r]
Jan 1 19:51:59 fileserver FaxGetty[2869]: -->
[14:0,1,1.0,2,8,10]
Jan 1 19:51:59 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports
"Data"
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class
1"
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class
2"
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports "Class
1.0"
Jan 1 19:51:59 fileserver FaxGetty[2869]: MODEM Supports
"Voice"
Jan 1 19:51:59 fileserver FaxGetty[2869]: <--
[12:AT+FCLASS=1\r]
Jan 1 19:52:00 fileserver FaxGetty[2869]: -->
[2:OK]
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM: Mfr
Rockwell
Jan 1 19:52:00 fileserver FaxGetty[2869]: <--
[5:ATI3\r]
Jan 1 19:52:00 fileserver FaxGetty[2869]: --> [21:EM3900
External Modem]
Jan 1 19:52:00 fileserver FaxGetty[2869]: -->
[34:Patch 9-11 NVM + SIN + MALY + THAI]
Jan 1 19:52:00 fileserver
FaxGetty[2869]: --> [2:OK]
Jan 1 19:52:00 fileserver FaxGetty[2869]:
MODEM: Model RC288DPi
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM:
Revision EM3900 External Modem Patch 9-11 NVM + SIN + MALY + THAI
Jan 1
19:52:00 fileserver FaxGetty[2869]: <-- [9:AT+FTM=?\r]
Jan 1
19:52:00 fileserver FaxGetty[2869]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Jan 1 19:52:00
fileserver FaxGetty[2869]: --> [2:OK]
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 3.85 line/mm
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 7.7 line/mm
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 2400 bit/s
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 4800 bit/s
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 7200 bit/s
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 9600 bit/s
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 12000 bit/s
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 14400 bit/s
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports page width 1728 pixels in 215 mm
Jan 1
19:52:00 fileserver FaxGetty[2869]: MODEM Supports page width 2048 pixels in 255
mm
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM Supports page width
2432 pixels in 303 mm
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM
Supports A4 page length (297 mm)
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports B4 page length (364 mm)
Jan 1 19:52:00
fileserver FaxGetty[2869]: MODEM Supports unlimited page length
Jan 1
19:52:00 fileserver FaxGetty[2869]: MODEM Supports 1-D MR
Jan 1
19:52:00 fileserver FaxGetty[2869]: MODEM Supports 2-D MR
Jan 1 19:52:00 fileserver FaxGetty[2869]:
MODEM Supports 0 ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]:
MODEM Supports 5 ms/scanline
Jan 1 19:52:00 fileserver FaxGetty[2869]:
MODEM Supports 10 ms, 5 ms/scanline
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 10 ms/scanline
Jan 1 19:52:00 fileserver
FaxGetty[2869]: MODEM Supports 20 ms, 10 ms/scanline
Jan 1 19:52:00
fileserver FaxGetty[2869]: MODEM Supports 20 ms/scanline
Jan 1 19:52:00
fileserver FaxGetty[2869]: MODEM Supports 40 ms, 20 ms/scanline
Jan 1
19:52:00 fileserver FaxGetty[2869]: MODEM Supports 40 ms/scanline
Jan 1
19:52:00 fileserver FaxGetty[2869]: <-- [9:AT+FRM=?\r]
Jan 1
19:52:00 fileserver FaxGetty[2869]: --> [4:RING]
Jan 1 19:52:00
fileserver FaxGetty[2869]: Error parsing "+FRM" query response:
"OK"
Jan 1 19:52:00 fileserver FaxGetty[2869]: MODEM set DTR
OFF
Jan 1 19:52:00 fileserver FaxGetty[2869]: /dev/ttyS0: Can not
initialize modem.
Jan 1 19:52:00 fileserver FaxGetty[2869]: STATE
CHANGE: RECEIVING -> MODEMWAIT (timeout 30)
Please help!!!
Rachel Seok
