|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] RECV: REJECT page quality...
Re-configure the modem in Class1.
--- Luca Abeni <labeni@mbigroup.it> wrote:
> Hello everyone,
>
> I recently installed hylafax on a redhat 7.3, using
> an
> USROBOTICS COURIER V.EVERYTHING
> modem, and it generally works very well.
>
> However, I cannot receive faxes from some machines
> (the caller giving
> the problem is always the same); the log is at the
> end of this mail.
> Since almost all the lines are received bad, it is
> clear that there
> is some problem... Faxes from this caller are
> received correctly using
> a different fax machine, so the problem is on my
> side (and it is not a
> line problem)...
> On the other hand, I receive faxes correctly from
> other machines, so my
> configuration is not totally wrong ;)
>
> I searched the ml archives, and I found some reports
> of similar
> problems, but I was not able to find a solution...
> :(
> Can anyone help me?
>
> Thanks,
> Luca
>
> P.S.: please, cc me in the reply, since I am not
> subscribed to the list
>
> Here is my config.ttyS0:
> LongDistancePrefix: 1
> InternationalPrefix: 00
> DialStringRules: etc/dialrules
> ServerTracing: 1
> SessionTracing: 11
> RecvFileMode: 0600
> LogFileMode: 0600
> DeviceMode: 0600
> RingsBeforeAnswer: 1
> SpeakerVolume: on
>
> PercentGoodLines: 0
> MaxConsecutiveBadLines: 0
>
>
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: "MBI SRL"
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "From %%l|%c|Page %%P of
> %%T"
> MaxRecvPages: 25
> #
> #
> # Modem-related stuff: should reflect modem command
> interface
> # and hardware connection/cabling (e.g. flow
> control).
> #
> ModemType: Class2.0 # use class
> 2.0 interface
> ModemRate: 19200 # DCE-DTE
> communication rate
> ModemFlowControl: rtscts # hardware
> flow control
> #
> ModemNoFlowCmd: AT&H0&I0&R1 # setup
> modem for no flow
> control
> ModemHardFlowCmd: AT&H1&I0&R2 # setup
> modem for hardware flow
> control
> ModemSoftFlowCmd: AT&H2&I2&R1 # setup
> modem for software flow
> control
> #
> ModemSetupDTRCmd: ATS13=1&D2 # setup so
> DTR drop resets modem
> ModemSetupDCDCmd: AT&C1 # setup so
> DCD reflects carrier
> (or not)
> ModemResultCodesCmd: ATQ0X4 # enable
> extended result codes
> #
> # NB: adaptive answer only seems to work properly
> when
> # the modem is left idling in Class 2.0
> #
> ModemSetupAACmd: AT+FAA=1
> #
> # Set modem speaker volume commands: OFF QUIET LOW
> MEDIUM HIGH.
> # Note that we both turn the speaker on/off and set
> volume.
> #
> ModemSetVolumeCmd: "ATM0 ATM1 ATM1 ATM1 ATM1"
> #
> # Modem does not support HDLC frame tracing; we add
> this just
> # to eliminate spurious ERROR results that confuse
> the naive.
> #
> Class2BUGCmd: AT+FBU=0
> #
> # The modem doesn't support copy quality checking,
> even though it
> # returns (0-2,0-2) for AT+FCQ=?; therefore we
> override the query
> # response so that the server will do copy quality
> checking.
> #
> Class2CQQueryCmd: !(0),(0) # override
> modem response
> #
> #Class2CQCmd: AT+FCQ=0
>
> #
> # Disables the reporting of bad frames by the modem.
> This
> # overcomes a firmware problem in the x2 and V90
> Sportsters.
> # It is not necessary for the Courier modem.
> #
> Class2NRCmd: AT+FNR=1,1,1,0
> #
> # USR modems violate Class 2.0 specs and do not send
> RTC itself
> #
> Class2SendRTC: yes
> #
> # +FAP=? not supported on this modem, gives ERROR in
> ServerTracing
> #
> Class2APQueryCmd: none
>
> # We need this, because of the dialtone issue...
> ModemDialCmd: "ATX3 ATDT%s" # T
> for tone dialing
>
> The log:
> Jan 14 10:43:29.09: [ 9499]: SESSION BEGIN 00000021
> 390508754908
> Jan 14 10:43:29.09: [ 9499]: HylaFAX (tm) Version
> 4.1.5
> Jan 14 10:43:29.09: [ 9499]: <-- [4:ATA\r]
> Jan 14 10:43:35.80: [ 9499]: --> [4:+FCO]
> Jan 14 10:43:35.80: [ 9499]: ANSWER: FAX CONNECTION
> DEVICE '/dev/ttyS0'
> Jan 14 10:43:35.80: [ 9499]: RECV FAX: begin
> Jan 14 10:43:37.45: [ 9499]: --> [27:+FTI:"
> 095 416654"]
> Jan 14 10:43:37.45: [ 9499]: REMOTE TSI "095 416654"
> Jan 14 10:43:37.71: [ 9499]: -->
> [20:+FCS:0,3,0,2,0,0,0,1]
> Jan 14 10:43:37.71: [ 9499]: REMOTE wants 9600 bit/s
> Jan 14 10:43:37.71: [ 9499]: REMOTE wants page width
> 1728 pixels in 215
> mm
> Jan 14 10:43:37.71: [ 9499]: REMOTE wants unlimited
> page length
> Jan 14 10:43:37.71: [ 9499]: REMOTE wants 3.85
> line/mm
> Jan 14 10:43:37.71: [ 9499]: REMOTE wants 1-D MR
> Jan 14 10:43:37.84: [ 9499]: --> [2:OK]
> Jan 14 10:43:37.84: [ 9499]: <-- [7:AT+FDR\r]
> Jan 14 10:43:39.84: [ 9499]: -->
> [20:+FCS:0,3,0,2,0,0,0,1]
> Jan 14 10:43:39.84: [ 9499]: REMOTE wants 9600 bit/s
> Jan 14 10:43:39.84: [ 9499]: REMOTE wants page width
> 1728 pixels in 215
> mm
> Jan 14 10:43:39.84: [ 9499]: REMOTE wants unlimited
> page length
> Jan 14 10:43:39.84: [ 9499]: REMOTE wants 3.85
> line/mm
> Jan 14 10:43:39.84: [ 9499]: REMOTE wants 1-D MR
> Jan 14 10:43:41.46: [ 9499]: --> [7:CONNECT]
> Jan 14 10:43:41.46: [ 9499]: RECV: begin page
> Jan 14 10:43:41.46: [ 9499]: RECV: send trigger 022
> Jan 14 10:43:41.46: [ 9499]: <-- data [1]
> Jan 14 10:43:58.79: [ 9499]: RECV: 9 total lines, 8
> bad lines, 8
> consecutive bad lines
> Jan 14 10:43:58.79: [ 9499]: -->
> [15:+FPS:1,46,0,0,0]
> Jan 14 10:44:00.05: [ 9499]: --> [6:+FET:2]
> Jan 14 10:44:00.05: [ 9499]: RECV recv EOP (no more
> pages or documents)
> Jan 14 10:44:00.05: [ 9499]: --> [2:OK]
> Jan 14 10:44:00.05: [ 9499]: RECV: REJECT page
> quality, 11% good lines
> (95% required)
> Jan 14 10:44:00.05: [ 9499]: RECV send RTN (retrain
> negative)
> Jan 14 10:44:00.05: [ 9499]: <-- [9:AT+FPS=2\r]
> Jan 14 10:44:00.20: [ 9499]: --> [5:ERROR]
> Jan 14 10:44:00.20: [ 9499]: MODEM Command error
>
=== message truncated ===
__________________________________________________
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
http://mailplus.yahoo.com
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
