Re: [hylafax-users] zyxel u-1496e config

To: "hylafax" <hylafax-users@hylafax.org>
Subject: Re: [hylafax-users] zyxel u-1496e config
From: "Dan" <dwright@spca.org>
Date: Tue, 28 Aug 2001 09:12:50 -0500


At 04:23 PM 8/27/01 -0500, Dan wrote:
>I just installed redhat 7.1 and hylafax 4.1 my modem is a
>Zyxel u-1496e with the latest firmware. I have tried this modem in
>both class 1 and class 2.  I am getting lots (all most all) of:  Failure to
>train remote
> modem at 2400 bps or minimum speed; Giving up after 3 attempts to send
same
>page

It's probably not your config file.  Would you please send a session log?

Lee.


Lee is this what you want i xx out phone numbers and such.

Dan


Your facsimile job to xxx-xxx-xxxx failed because:
    Failure to train remote modem at 2400 bps or minimum speed; Giving up
after 3 attempts to send same page

    ---- Transcript of session follows ----

Aug 20 20:51:21.73: [13126]: SESSION BEGIN 00002958 12142149437352
Aug 20 20:51:21.73: [13126]: SEND FAX: JOB 2834 DEST xxx-xxx-xxxx COMMID
00002958
Aug 20 20:51:21.73: [13126]: MODEM set DTR OFF
Aug 20 20:51:21.73: [13126]: DELAY 2600 ms
Aug 20 20:51:24.32: [13126]: MODEM set DTR ON
Aug 20 20:51:24.33: [13126]: MODEM set baud rate: 19200 baud, input flow
XON/XOFF, output flow XON/XOFF
Aug 20 20:51:24.33: [13126]: MODEM flush i/o
Aug 20 20:51:24.33: [13126]: <-- [4:ATZ\r]
Aug 20 20:51:25.06: [13126]: --> [2:OK]
Aug 20 20:51:25.06: [13126]: <-- [15:ATE0V1Q0S0=0H0\r]
Aug 20 20:51:25.08: [13126]: --> [14:ATE0V1Q0S0=0H0]
Aug 20 20:51:25.08: [13126]: --> [2:OK]
Aug 20 20:51:25.08: [13126]: <-- [15:ATS8=2S7=60&K4\r]
Aug 20 20:51:25.10: [13126]: --> [2:OK]
Aug 20 20:51:25.10: [13126]: <-- [12:AT+FCLASS=1\r]
Aug 20 20:51:25.12: [13126]: --> [2:OK]
Aug 20 20:51:25.12: [13126]: <-- [7:ATL0M1\r]
Aug 20 20:51:25.13: [13126]: --> [2:OK]
Aug 20 20:51:25.13: [13126]: STATE CHANGE: RUNNING -> SENDING
Aug 20 20:51:25.13: [13126]: MODEM input buffering enabled
Aug 20 20:51:25.14: [13126]: <-- [12:AT+FCLASS=1\r]
Aug 20 20:51:25.25: [13126]: --> [2:OK]
Aug 20 20:51:25.25: [13126]: MODEM set XON/XOFF/FLUSH: input ignored, output
disabled
Aug 20 20:51:25.26: [13126]: DIAL 2149437352
Aug 20 20:51:25.26: [13126]: <-- [15:ATDT2149437352\r]
Aug 20 20:51:41.81: [13126]: --> [7:CONNECT]
Aug 20 20:51:41.81: [13126]: MODEM input buffering disabled
Aug 20 20:51:43.64: [13126]: --> HDLC<39:FF C0 04 00 00 70 00 00 00 69 F0 80
C0 00 08 00 40 A9 00 43 07 86 0F 3E BF E2 C7 01 1E 3F 02 79 E3 EF 28 00 2C
1A 3C>
Aug 20 20:51:43.65: [13126]: --> [5:ERROR]
Aug 20 20:51:43.65: [13126]: MODEM Command error
Aug 20 20:51:43.65: [13126]: FCS error
Aug 20 20:51:43.65: [13126]: DELAY 200 ms
Aug 20 20:51:43.85: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:51:43.87: [13126]: --> [7:CONNECT]
Aug 20 20:51:44.06: [13126]: --> HDLC<11:FF C0 02 10 00 61 00 06 10 04 CC>
Aug 20 20:51:44.07: [13126]: --> [5:ERROR]
Aug 20 20:51:44.07: [13126]: MODEM Command error
Aug 20 20:51:44.07: [13126]: FCS error
Aug 20 20:51:44.07: [13126]: DELAY 200 ms
Aug 20 20:51:44.27: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:51:44.29: [13126]: --> [7:CONNECT]
Aug 20 20:51:49.29: [13126]: MODEM TIMEOUT: receiving HDLC frame data
Aug 20 20:51:49.49: [13126]: MODEM TIMEOUT: reading line from modem
Aug 20 20:51:49.49: [13126]: MODEM <Timeout>
Aug 20 20:51:49.49: [13126]: DELAY 200 ms
Aug 20 20:51:49.69: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:51:49.71: [13126]: --> [7:CONNECT]
Aug 20 20:51:54.71: [13126]: MODEM TIMEOUT: receiving HDLC frame data
Aug 20 20:51:54.91: [13126]: MODEM TIMEOUT: reading line from modem
Aug 20 20:51:54.91: [13126]: MODEM <Timeout>
Aug 20 20:51:54.91: [13126]: DELAY 200 ms
Aug 20 20:51:55.11: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:51:55.13: [13126]: --> [7:CONNECT]
Aug 20 20:52:00.13: [13126]: MODEM TIMEOUT: receiving HDLC frame data
Aug 20 20:52:00.33: [13126]: MODEM TIMEOUT: reading line from modem
Aug 20 20:52:00.33: [13126]: MODEM <Timeout>
Aug 20 20:52:00.33: [13126]: DELAY 200 ms
Aug 20 20:52:00.53: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:52:00.55: [13126]: --> [7:CONNECT]
Aug 20 20:52:00.56: [13126]: --> HDLC<25:FF C0 02 74 C6 76 92 04 34 CE EE A6
72 04 CE A6 26 86 26 A6 6E F6 72 89 37>
Aug 20 20:52:00.57: [13126]: --> [2:OK]
Aug 20 20:52:00.57: [13126]: REMOTE CSI "Novedades News, Inc."
Aug 20 20:52:00.57: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:52:00.59: [13126]: --> [7:CONNECT]
Aug 20 20:52:00.60: [13126]: --> HDLC<12:FF C8 01 00 77 1F 23 01 09 88 20
41>
Aug 20 20:52:00.60: [13126]: --> [2:OK]
Aug 20 20:52:00.60: [13126]: REMOTE best rate 14400 bit/s
Aug 20 20:52:00.60: [13126]: REMOTE max page width 1728 pixels in 215 mm
Aug 20 20:52:00.60: [13126]: REMOTE max unlimited page length
Aug 20 20:52:00.61: [13126]: REMOTE best vres 7.7 line/mm
Aug 20 20:52:00.61: [13126]: REMOTE best format 2-D MMR
Aug 20 20:52:00.61: [13126]: REMOTE supports T.30 Annex A, ECM
Aug 20 20:52:00.61: [13126]: REMOTE best 0 ms/scanline
Aug 20 20:52:00.61: [13126]: USE 14400 bit/s
Aug 20 20:52:00.61: [13126]: USE 0 ms/scanline
Aug 20 20:52:00.61: [13126]: SEND file "docq/doc2834.cover;40"
Aug 20 20:52:00.61: [13126]: USE page width 1728 pixels in 215 mm
Aug 20 20:52:00.61: [13126]: USE unlimited page length
Aug 20 20:52:00.61: [13126]: USE 3.85 line/mm
Aug 20 20:52:00.61: [13126]: USE 2-D MR
Aug 20 20:52:00.61: [13126]: SEND training at v.17 14400 bit/s
Aug 20 20:52:00.61: [13126]: <-- [9:AT+FTH=3\r]
Aug 20 20:52:00.66: [13126]: --> [7:CONNECT]
Aug 20 20:52:00.66: [13126]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04>
Aug 20 20:52:02.45: [13126]: --> [7:CONNECT]
Aug 20 20:52:02.45: [13126]: <-- HDLC<6:FF C8 C1 00 45 1E>
Aug 20 20:52:02.88: [13126]: --> [2:OK]
Aug 20 20:52:02.88: [13126]: DELAY 75 ms
Aug 20 20:52:02.96: [13126]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Aug 20 20:52:02.96: [13126]: <-- [11:AT+FTM=145\r]
Aug 20 20:52:03.00: [13126]: --> [7:CONNECT]
Aug 20 20:52:06.11: [13126]: --> [2:OK]
Aug 20 20:52:06.11: [13126]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Aug 20 20:52:06.11: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:52:09.21: [13126]: --> [0:]
Aug 20 20:52:09.21: [13126]: MODEM <Empty line>
Aug 20 20:52:09.21: [13126]: MODEM TIMEOUT: waiting for v.21 carrier
Aug 20 20:52:09.27: [13126]: --> [2:OK]
Aug 20 20:52:09.27: [13126]: DELAY 1500 ms
Aug 20 20:52:10.77: [13126]: SEND training at v.17 12000 bit/s
Aug 20 20:52:10.77: [13126]: <-- [9:AT+FTH=3\r]
Aug 20 20:52:10.83: [13126]: --> [7:CONNECT]
Aug 20 20:52:10.83: [13126]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04>
Aug 20 20:52:12.61: [13126]: --> [7:CONNECT]
Aug 20 20:52:12.61: [13126]: <-- HDLC<6:FF C8 C1 00 55 1E>
Aug 20 20:52:13.05: [13126]: --> [2:OK]
Aug 20 20:52:13.05: [13126]: DELAY 75 ms
Aug 20 20:52:13.13: [13126]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Aug 20 20:52:13.13: [13126]: <-- [11:AT+FTM=121\r]
Aug 20 20:52:13.17: [13126]: --> [7:CONNECT]
Aug 20 20:52:16.28: [13126]: --> [2:OK]
Aug 20 20:52:16.28: [13126]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Aug 20 20:52:16.28: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:52:19.38: [13126]: --> [0:]
Aug 20 20:52:19.38: [13126]: MODEM <Empty line>
Aug 20 20:52:19.38: [13126]: MODEM TIMEOUT: waiting for v.21 carrier
Aug 20 20:52:19.44: [13126]: --> [2:OK]
Aug 20 20:52:19.44: [13126]: DELAY 1500 ms
Aug 20 20:52:20.94: [13126]: SEND training at v.17 9600 bit/s
Aug 20 20:52:20.94: [13126]: <-- [9:AT+FTH=3\r]
Aug 20 20:52:20.99: [13126]: --> [7:CONNECT]
Aug 20 20:52:20.99: [13126]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04>
Aug 20 20:52:22.78: [13126]: --> [7:CONNECT]
Aug 20 20:52:22.78: [13126]: <-- HDLC<6:FF C8 C1 00 65 1E>
Aug 20 20:52:23.21: [13126]: --> [2:OK]
Aug 20 20:52:23.21: [13126]: DELAY 75 ms
Aug 20 20:52:23.29: [13126]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Aug 20 20:52:23.29: [13126]: <-- [10:AT+FTM=97\r]
Aug 20 20:52:23.33: [13126]: --> [7:CONNECT]
Aug 20 20:52:26.44: [13126]: --> [2:OK]
Aug 20 20:52:26.44: [13126]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Aug 20 20:52:26.44: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:52:29.54: [13126]: --> [0:]
Aug 20 20:52:29.54: [13126]: MODEM <Empty line>
Aug 20 20:52:29.54: [13126]: MODEM TIMEOUT: waiting for v.21 carrier
Aug 20 20:52:29.60: [13126]: --> [2:OK]
Aug 20 20:52:29.60: [13126]: DELAY 1500 ms
Aug 20 20:52:31.10: [13126]: SEND training at v.17 7200 bit/s
Aug 20 20:52:31.10: [13126]: <-- [9:AT+FTH=3\r]
Aug 20 20:52:31.15: [13126]: --> [7:CONNECT]
Aug 20 20:52:31.15: [13126]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04>
Aug 20 20:52:32.94: [13126]: --> [7:CONNECT]
Aug 20 20:52:32.94: [13126]: <-- HDLC<6:FF C8 C1 00 75 1E>
Aug 20 20:52:33.37: [13126]: --> [2:OK]
Aug 20 20:52:33.37: [13126]: DELAY 75 ms
Aug 20 20:52:33.45: [13126]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Aug 20 20:52:33.45: [13126]: <-- [10:AT+FTM=73\r]
Aug 20 20:52:33.49: [13126]: --> [7:CONNECT]
Aug 20 20:52:36.60: [13126]: --> [2:OK]
Aug 20 20:52:36.60: [13126]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Aug 20 20:52:36.60: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:52:39.70: [13126]: --> [0:]
Aug 20 20:52:39.70: [13126]: MODEM <Empty line>
Aug 20 20:52:39.70: [13126]: MODEM TIMEOUT: waiting for v.21 carrier
Aug 20 20:52:39.76: [13126]: --> [2:OK]
Aug 20 20:52:39.76: [13126]: DELAY 1500 ms
Aug 20 20:52:41.26: [13126]: SEND training at v.27ter 4800 bit/s
Aug 20 20:52:41.26: [13126]: <-- [9:AT+FTH=3\r]
Aug 20 20:52:41.31: [13126]: --> [7:CONNECT]
Aug 20 20:52:41.31: [13126]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04>
Aug 20 20:52:43.10: [13126]: --> [7:CONNECT]
Aug 20 20:52:43.10: [13126]: <-- HDLC<6:FF C8 C1 00 51 1E>
Aug 20 20:52:43.54: [13126]: --> [2:OK]
Aug 20 20:52:43.54: [13126]: DELAY 75 ms
Aug 20 20:52:43.62: [13126]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Aug 20 20:52:43.62: [13126]: <-- [10:AT+FTM=48\r]
Aug 20 20:52:43.68: [13126]: --> [7:CONNECT]
Aug 20 20:52:46.11: [13126]: --> [2:OK]
Aug 20 20:52:46.11: [13126]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Aug 20 20:52:46.11: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:52:49.21: [13126]: --> [0:]
Aug 20 20:52:49.21: [13126]: MODEM <Empty line>
Aug 20 20:52:49.21: [13126]: MODEM TIMEOUT: waiting for v.21 carrier
Aug 20 20:52:49.27: [13126]: --> [2:OK]
Aug 20 20:52:49.27: [13126]: DELAY 1500 ms
Aug 20 20:52:50.77: [13126]: SEND training at v.27ter fallback mode 2400
bit/s
Aug 20 20:52:50.77: [13126]: <-- [9:AT+FTH=3\r]
Aug 20 20:52:50.82: [13126]: --> [7:CONNECT]
Aug 20 20:52:50.82: [13126]: <-- HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04
04 04 04 04 04 04 04 04 04 04 04>
Aug 20 20:52:52.61: [13126]: --> [7:CONNECT]
Aug 20 20:52:52.61: [13126]: <-- HDLC<6:FF C8 C1 00 41 1E>
Aug 20 20:52:53.05: [13126]: --> [2:OK]
Aug 20 20:52:53.05: [13126]: DELAY 75 ms
Aug 20 20:52:53.13: [13126]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Aug 20 20:52:53.13: [13126]: <-- [10:AT+FTM=24\r]
Aug 20 20:52:53.20: [13126]: --> [7:CONNECT]
Aug 20 20:52:55.87: [13126]: --> [2:OK]
Aug 20 20:52:55.87: [13126]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Aug 20 20:52:55.87: [13126]: <-- [9:AT+FRH=3\r]
Aug 20 20:52:58.97: [13126]: --> [0:]
Aug 20 20:52:58.97: [13126]: MODEM <Empty line>
Aug 20 20:52:58.97: [13126]: MODEM TIMEOUT: waiting for v.21 carrier
Aug 20 20:52:59.03: [13126]: --> [2:OK]
Aug 20 20:52:59.04: [13126]: DELAY 1500 ms
Aug 20 20:53:00.53: [13126]: TRAINING failed
Aug 20 20:53:00.54: [13126]: SEND: Failure to train remote modem at 2400 bps
or minimum speed; Giving up after 3 attempts to send same page
"docq/doc2834.cover;40", dirnum 0
Aug 20 20:53:00.54: [13126]: <-- [9:AT+FTH=3\r]
Aug 20 20:53:00.59: [13126]: --> [7:CONNECT]
Aug 20 20:53:00.59: [13126]: <-- HDLC<3:FF C8 DF>
Aug 20 20:53:01.91: [13126]: --> [2:OK]
Aug 20 20:53:01.91: [13126]: MODEM input buffering enabled
Aug 20 20:53:01.91: [13126]: <-- [5:ATH0\r]
Aug 20 20:53:03.01: [13126]: --> [2:OK]
Aug 20 20:53:03.01: [13126]: MODEM set DTR OFF
Aug 20 20:53:03.01: [13126]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Aug 20 20:53:03.02: [13126]: SESSION END

    ---- Unsent job status ----

   Destination: xxx-xxx-xxxx
         JobID: 2834
       GroupID: 2834
        Sender: anita
      Mailaddr: dan@xxxxxx
        CommID: 00002958
Submitted From: 192.168.1.7
    Page Width: 194 (mm)
   Page Length: 281 (mm)
    Resolution: 98 (lpi)
        Status: Failure to train remote modem at 2400 bps or minimum speed;
Giving up after 3 attempts to send same page
       Dialogs: 3 (exchanges with remote device)
         Dials: 0 (consecutive failed calls to destination)
         Calls: 3 (total phone calls placed)
         Pages: 0 (pages transmitted)
      TotPages: 2 (total pages to transmit)
      Attempts: 3 (attempts to send current page)
        Dirnum: 0 (directory of next page to send)

    ---- Documents submitted for transmission ----

The following documents were submitted for transmission and are
available on the server for reuse until they are automatically
purged when this job is removed.  Documents may also be manually
removed using the faxrm command; consult faxrm(1) for information.

Filename                 Size Type
docq/doc2834.cover          0 PostScript cover page
docq/doc4230.ps             0 PostScript

>does anyone have a modem config file that works good?  I tried the one that
>came with Hylafax but haven't had much luck.




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
Follow-Ups:
- Re: [hylafax-users] zyxel u-1496e config
  - From: Lee Howard
References:
- Re: [hylafax-users] zyxel u-1496e config
  - From: Lee Howard
Prev by Date: Re: [hylafax-users] job group rules
Next by Date: Re: [hylafax-users] sent faxes are shorter than original
Previous by thread: Re: [hylafax-users] zyxel u-1496e config
Next by thread: Re: [hylafax-users] zyxel u-1496e config
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services