Re: [hylafax-users] faxes are cut off

To: hylafax <hylafax-users@hylafax.org>
Subject: Re: [hylafax-users] faxes are cut off
From: "darcy w. christ" <darcy@elegant.com>
Date: Tue, 03 Jul 2001 13:13:30 -0400
hi,

 i've upgraded to 4.1. i'm still having trouble with the way my faxes
are coming out.  i've simplified my situation - i'm testing by using:
 
  sendfax -n -d XXXXXXXXX /etc/hosts

The page comes through as two pages.  The first page is fine, but the
second one is cut off on the first line (not the header).  That's the
same spot it was cutting off when i was using a coverpage.  Someone
recommended playing with the PageChop and ChopThreshold variables, but i
can't say i understand what i am to change them to.   i've included my
session tracing just in case there is something important in there.  i
appreciate any suggestions.


Jul 03 13:07:36.78: [23822]: SESSION BEGIN 00000003 14164163628324
Jul 03 13:07:36.78: [23822]: HylaFAX (tm) Version 4.1
Jul 03 13:07:36.78: [23822]: SEND FAX: JOB 2 DEST 4163628324 COMMID
00000003
Jul 03 13:07:36.78: [23822]: DEVICE '/dev/ttyS1'
Jul 03 13:07:36.78: [23822]: MODEM set DTR OFF
Jul 03 13:07:36.78: [23822]: DELAY 75 ms
Jul 03 13:07:36.85: [23822]: MODEM set DTR ON
Jul 03 13:07:36.85: [23822]: DELAY 2600 ms
Jul 03 13:07:39.45: [23822]: MODEM set baud rate: 38400 baud, input flow
RTS/CTS, output flow
RTS/CTS
Jul 03 13:07:39.45: [23822]: MODEM flush i/o
Jul 03 13:07:39.45: [23822]: <-- [4:ATZ\r]
Jul 03 13:07:42.03: [23822]: --> [2:OK]
Jul 03 13:07:42.03: [23822]: <-- [5:ATE0\r]
Jul 03 13:07:42.17: [23822]: --> [4:ATE0]
Jul 03 13:07:42.17: [23822]: --> [2:OK]
Jul 03 13:07:42.17: [23822]: <-- [5:ATV1\r]
Jul 03 13:07:42.31: [23822]: --> [2:OK]
Jul 03 13:07:42.31: [23822]: <-- [5:ATQ0\r]
Jul 03 13:07:42.45: [23822]: --> [2:OK]
Jul 03 13:07:42.45: [23822]: <-- [7:ATS0=0\r]
Jul 03 13:07:42.59: [23822]: --> [2:OK]
Jul 03 13:07:42.59: [23822]: <-- [7:ATS8=2\r]
Jul 03 13:07:42.73: [23822]: --> [2:OK]
Jul 03 13:07:42.73: [23822]: <-- [8:ATS7=60\r]
Jul 03 13:07:42.87: [23822]: --> [2:OK]
Jul 03 13:07:42.87: [23822]: <-- [6:AT&K3\r]
Jul 03 13:07:43.01: [23822]: --> [2:OK]
Jul 03 13:07:43.01: [23822]: <-- [6:AT&D3\r]
Jul 03 13:07:43.15: [23822]: --> [2:OK]
Jul 03 13:07:43.15: [23822]: <-- [6:AT&C1\r]
Jul 03 13:07:43.29: [23822]: --> [2:OK]
Jul 03 13:07:43.29: [23822]: <-- [12:AT+FCLASS=1\r]
Jul 03 13:07:43.44: [23822]: --> [2:OK]
Jul 03 13:07:43.44: [23822]: <-- [9:AT+FAA=0\r]
Jul 03 13:07:43.45: [23822]: --> [2:OK]
Jul 03 13:07:43.45: [23822]: <-- [5:ATM0\r]
Jul 03 13:07:43.46: [23822]: --> [2:OK]
Jul 03 13:07:43.46: [23822]: STATE CHANGE: RUNNING -> SENDING
Jul 03 13:07:43.46: [23822]: MODEM input buffering enabled
Jul 03 13:07:43.46: [23822]: <-- [12:AT+FCLASS=1\r]
Jul 03 13:07:43.57: [23822]: --> [2:OK]
Jul 03 13:07:43.58: [23822]: DIAL 4163628324
Jul 03 13:07:43.58: [23822]: <-- [15:ATDT4163628324\r]
Jul 03 13:07:57.53: [23822]: --> [7:CONNECT]
Jul 03 13:07:57.53: [23822]: MODEM input buffering disabled
Jul 03 13:07:59.59: [23822]: --> HDLC<50:FF C0 04 00 00 8A 00 00 20 89
45 4C 45 47 41 4E 54 20
43 4F 4D 4D 55 4E 49 43 41 54 49 4F 4E 53 20 20 FF FF FF FF FF FF FF FF
82 72 FF FF 00 00 67
BC>
Jul 03 13:07:59.60: [23822]: --> [2:OK]
Jul 03 13:07:59.60: [23822]: REMOTE NSF "00 00 51 00 00 04 91 A2 32 A2
E2 82 72 2A 04 C2 F2 B2
B2 AA 72 92 C2 82 2A 92 F2 72 CA 04 04 FF FF FF FF FF FF FF FF 41 4E FF
FF 00 00 E6"
Jul 03 13:07:59.60: [23822]: NSF remote fax equipment: Sanyo 
Jul 03 13:07:59.60: [23822]: <-- [9:AT+FRH=3\r]
Jul 03 13:07:59.61: [23822]: --> [7:CONNECT]
Jul 03 13:08:00.31: [23822]: --> HDLC<25:FF C0 02 2C 4C CC 1C 04 4C 6C
CC 04 6C 8C 2C 04 04 04
04 04 04 04 04 32 78>
Jul 03 13:08:00.32: [23822]: --> [2:OK]
Jul 03 13:08:00.32: [23822]: REMOTE CSI "416 362 8324"
Jul 03 13:08:00.32: [23822]: <-- [9:AT+FRH=3\r]
Jul 03 13:08:00.33: [23822]: --> [7:CONNECT]
Jul 03 13:08:00.63: [23822]: --> HDLC<11:FF C8 01 00 77 19 23 01 08 39
77>
Jul 03 13:08:00.64: [23822]: --> [2:OK]
Jul 03 13:08:00.64: [23822]: REMOTE best rate 14400 bit/s
Jul 03 13:08:00.64: [23822]: REMOTE max page width 1728 pixels in 215 mm
Jul 03 13:08:00.64: [23822]: REMOTE max unlimited page length 
Jul 03 13:08:00.64: [23822]: REMOTE best vres 7.7 line/mm
Jul 03 13:08:00.64: [23822]: REMOTE best format 2-D MMR
Jul 03 13:08:00.64: [23822]: REMOTE supports T.30 Annex A, ECM
Jul 03 13:08:00.64: [23822]: REMOTE best 5 ms/scanline
Jul 03 13:08:00.64: [23822]: USE 14400 bit/s
Jul 03 13:08:00.64: [23822]: USE 5 ms/scanline
Jul 03 13:08:00.64: [23822]: SEND file "docq/doc2.ps;30"
Jul 03 13:08:00.64: [23822]: USE page width 1728 pixels in 215 mm
Jul 03 13:08:00.64: [23822]: USE unlimited page length 
Jul 03 13:08:00.64: [23822]: USE 3.85 line/mm
Jul 03 13:08:00.64: [23822]: USE 1-D MR
Jul 03 13:08:00.64: [23822]: SEND training at v.17 14400 bit/s
Jul 03 13:08:00.64: [23822]: <-- [9:AT+FTH=3\r]
Jul 03 13:08:00.69: [23822]: --> [7:CONNECT]
Jul 03 13:08:00.69: [23822]: <-- HDLC<23:FF C0 C2 E6 76 96 76 EE F6 4E
46 EC CC 8C 04 04 04 04
04 04 04 04 04>
Jul 03 13:08:00.69: [23822]: <-- data [23]
Jul 03 13:08:00.69: [23822]: <-- data [2]
Jul 03 13:08:02.43: [23822]: --> [7:CONNECT]
Jul 03 13:08:02.43: [23822]: <-- HDLC<6:FF C8 C1 00 44 18>
Jul 03 13:08:02.43: [23822]: <-- data [6]
Jul 03 13:08:02.43: [23822]: <-- data [2]
Jul 03 13:08:02.84: [23822]: --> [2:OK]
Jul 03 13:08:02.84: [23822]: DELAY 75 ms
Jul 03 13:08:02.92: [23822]: <-- [11:AT+FTM=145\r]
Jul 03 13:08:02.97: [23822]: --> [7:CONNECT]
Jul 03 13:08:02.97: [23822]: <-- data [1024]
Jul 03 13:08:02.97: [23822]: <-- data [1024]
Jul 03 13:08:02.97: [23822]: <-- data [652]
Jul 03 13:08:02.97: [23822]: <-- data [2]
Jul 03 13:08:06.13: [23822]: --> [2:OK]
Jul 03 13:08:06.13: [23822]: <-- [9:AT+FRH=3\r]
Jul 03 13:08:06.95: [23822]: --> [7:CONNECT]
Jul 03 13:08:07.91: [23822]: --> HDLC<5:FF C8 21 57 BE>
Jul 03 13:08:07.92: [23822]: --> [2:OK]
Jul 03 13:08:07.92: [23822]: TRAINING succeeded
Jul 03 13:08:07.92: [23822]: <-- [11:AT+FTM=146\r]
Jul 03 13:08:07.97: [23822]: --> [7:CONNECT]
Jul 03 13:08:07.97: [23822]: SEND begin page
Jul 03 13:08:07.98: [23822]: <-- data [1029]
Jul 03 13:08:07.98: [23822]: <-- data [1032]
Jul 03 13:08:07.98: [23822]: <-- data [1027]
Jul 03 13:08:07.98: [23822]: <-- data [1024]
Jul 03 13:08:08.34: [23822]: <-- data [1029]
Jul 03 13:08:08.82: [23822]: <-- data [1027]
Jul 03 13:08:09.38: [23822]: <-- data [1035]
Jul 03 13:08:09.97: [23822]: <-- data [1033]
Jul 03 13:08:10.54: [23822]: <-- data [1027]
Jul 03 13:08:11.11: [23822]: <-- data [434]
Jul 03 13:08:11.36: [23822]: SENT 9650 bytes of data
Jul 03 13:08:11.36: [23822]: <-- data [1030]
Jul 03 13:08:11.90: [23822]: <-- data [1027]
Jul 03 13:08:12.46: [23822]: <-- data [1028]
Jul 03 13:08:13.03: [23822]: <-- data [1027]
Jul 03 13:08:13.62: [23822]: <-- data [1027]
Jul 03 13:08:14.19: [23822]: <-- data [1031]
Jul 03 13:08:14.75: [23822]: <-- data [1028]
Jul 03 13:08:15.32: [23822]: <-- data [1031]
Jul 03 13:08:15.90: [23822]: <-- data [1027]
Jul 03 13:08:16.45: [23822]: <-- data [466]
Jul 03 13:08:16.71: [23822]: SENT 9682 bytes of data
Jul 03 13:08:16.71: [23822]: <-- data [1029]
Jul 03 13:08:17.29: [23822]: <-- data [1026]
Jul 03 13:08:17.85: [23822]: <-- data [1026]
Jul 03 13:08:18.42: [23822]: <-- data [1026]
Jul 03 13:08:19.01: [23822]: <-- data [1024]
Jul 03 13:08:19.57: [23822]: <-- data [1026]
Jul 03 13:08:20.12: [23822]: <-- data [1027]
Jul 03 13:08:20.70: [23822]: <-- data [1025]
Jul 03 13:08:21.25: [23822]: <-- data [1028]
Jul 03 13:08:21.83: [23822]: <-- data [463]
Jul 03 13:08:22.08: [23822]: SENT 9676 bytes of data
Jul 03 13:08:22.08: [23822]: <-- data [1028]
Jul 03 13:08:22.66: [23822]: <-- data [932]
Jul 03 13:08:23.19: [23822]: SENT 1956 bytes of data
Jul 03 13:08:23.19: [23822]: SEND 1D RTC
Jul 03 13:08:23.19: [23822]: <-- data [29]
Jul 03 13:08:23.19: [23822]: <-- data [2]
Jul 03 13:08:23.19: [23822]: SEND end page
Jul 03 13:08:25.60: [23822]: --> [2:OK]
Jul 03 13:08:25.60: [23822]: DELAY 75 ms
Jul 03 13:08:25.68: [23822]: SEND send MPS (more pages, same document)
Jul 03 13:08:25.68: [23822]: <-- [9:AT+FTH=3\r]
Jul 03 13:08:25.72: [23822]: --> [7:CONNECT]
Jul 03 13:08:25.72: [23822]: <-- HDLC<3:FF C8 F2>
Jul 03 13:08:25.72: [23822]: <-- data [3]
Jul 03 13:08:25.72: [23822]: <-- data [2]
Jul 03 13:08:27.03: [23822]: --> [2:OK]
Jul 03 13:08:27.03: [23822]: <-- [9:AT+FRH=3\r]
Jul 03 13:08:27.47: [23822]: --> [7:CONNECT]
Jul 03 13:08:28.43: [23822]: --> HDLC<5:FF C8 31 45 8F>
Jul 03 13:08:28.44: [23822]: --> [2:OK]
Jul 03 13:08:28.44: [23822]: SEND recv MCF (message confirmation)
Jul 03 13:08:28.44: [23822]: SEND FAX (00000003): FROM
root@one.1000camels.com TO 4163628324
(page 1 of 2 sent in 0:28)
Jul 03 13:08:28.44: [23822]: USE page width 1728 pixels in 215 mm
Jul 03 13:08:28.44: [23822]: USE unlimited page length 
Jul 03 13:08:28.44: [23822]: USE 3.85 line/mm
Jul 03 13:08:28.44: [23822]: USE 1-D MR
Jul 03 13:08:28.44: [23822]: <-- [11:AT+FTM=146\r]
Jul 03 13:08:28.49: [23822]: --> [7:CONNECT]
Jul 03 13:08:28.49: [23822]: SEND begin page
Jul 03 13:08:28.49: [23822]: <-- data [1028]
Jul 03 13:08:28.49: [23822]: <-- data [522]
Jul 03 13:08:28.49: [23822]: SENT 1545 bytes of data
Jul 03 13:08:28.49: [23822]: SEND 1D RTC
Jul 03 13:08:28.49: [23822]: <-- data [29]
Jul 03 13:08:28.49: [23822]: <-- data [2]
Jul 03 13:08:28.49: [23822]: SEND end page
Jul 03 13:08:29.78: [23822]: --> [2:OK]
Jul 03 13:08:29.78: [23822]: DELAY 95 ms
Jul 03 13:08:29.88: [23822]: SEND send EOP (no more pages or documents)
Jul 03 13:08:29.88: [23822]: <-- [9:AT+FTH=3\r]
Jul 03 13:08:29.92: [23822]: --> [7:CONNECT]
Jul 03 13:08:29.92: [23822]: <-- HDLC<3:FF C8 F4>
Jul 03 13:08:29.92: [23822]: <-- data [3]
Jul 03 13:08:29.92: [23822]: <-- data [2]
Jul 03 13:08:31.23: [23822]: --> [2:OK]
Jul 03 13:08:31.23: [23822]: <-- [9:AT+FRH=3\r]
Jul 03 13:08:31.67: [23822]: --> [7:CONNECT]
Jul 03 13:08:32.64: [23822]: --> HDLC<5:FF C8 31 45 8F>
Jul 03 13:08:32.64: [23822]: --> [2:OK]
Jul 03 13:08:32.64: [23822]: SEND recv MCF (message confirmation)
Jul 03 13:08:32.64: [23822]: SEND FAX (00000003): FROM
root@one.1000camels.com TO 4163628324
(page 2 of 2 sent in 0:04)
Jul 03 13:08:32.64: [23822]: SEND FAX (00000003): FROM
root@one.1000camels.com TO 4163628324
(docq/doc2.ps;30 sent in 0:32)
Jul 03 13:08:32.64: [23822]: <-- [9:AT+FTH=3\r]
Jul 03 13:08:32.69: [23822]: --> [7:CONNECT]
Jul 03 13:08:32.69: [23822]: <-- HDLC<3:FF C8 DF>
Jul 03 13:08:32.69: [23822]: <-- data [3]
Jul 03 13:08:32.69: [23822]: <-- data [2]
Jul 03 13:08:34.01: [23822]: --> [2:OK]
Jul 03 13:08:34.01: [23822]: MODEM input buffering enabled
Jul 03 13:08:34.01: [23822]: <-- [5:ATH0\r]
Jul 03 13:08:35.73: [23822]: --> [2:OK]
Jul 03 13:08:35.73: [23822]: MODEM set DTR OFF
Jul 03 13:08:35.73: [23822]: STATE CHANGE: SENDING -> MODEMWAIT (timeout
5)
Jul 03 13:08:35.73: [23822]: SESSION END

-- 
~darcy w. christ
Elegant Communications Inc.
416.362.9772 x222 | 416.362.8324 fax


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
Follow-Ups:
- Re: [hylafax-users] faxes are cut off
  - From: Giulio Orsero
Prev by Date: Re: [hylafax-users] Incoming call is allways addressed as fax!!?!?!
Next by Date: [hylafax-users] BrookTrout TruFAX
Previous by thread: Re: [hylafax-users] Config problem
Next by thread: Re: [hylafax-users] faxes are cut off
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services