flexfax: cannot send faxes, receive OK

["Steven A . DuChene" <sad@atl.hp.com>]

Downloaded 4.0pl2 binary version of HylaFAX for HP-UX 10.20
and I am attempting to set it up on a K460 running 10.20
with a US Robotics Sportster 33600/Fax V1.1

As I said in the title of this message I can receive a fax
just fine but when I try to send a fax I get a remote hang up
during the handshake part of the connection. I get the following
response in E-mail after session:

Your facsimile job to 81755 was not sent because:
    Unspecified Transmit Phase B error

    ---- Transcript of session follows ----

Oct 30 17:26:18.20: [ 9187]: SESSION BEGIN 00000037 181755
Oct 30 17:26:18.20: [ 9187]: SEND FAX: JOB 33 DEST 81755 COMMID 00000037
Oct 30 17:26:18.28: [ 9187]: DELAY 2600 ms
Oct 30 17:26:20.93: [ 9187]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Oct 30 17:26:21.14: [ 9187]: --> [2:OK]
Oct 30 17:26:21.14: [ 9187]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
Oct 30 17:26:21.39: [ 9187]: --> [2:OK]
Oct 30 17:26:21.39: [ 9187]: <-- [14:AT+FCLASS=2.0\r]
Oct 30 17:26:21.59: [ 9187]: --> [2:OK]
Oct 30 17:26:21.59: [ 9187]: <-- [9:AT+FLO=2\r]
Oct 30 17:26:21.79: [ 9187]: --> [2:OK]
Oct 30 17:26:21.79: [ 9187]: <-- [9:AT+FPP=0\r]
Oct 30 17:26:21.99: [ 9187]: --> [2:OK]
Oct 30 17:26:21.99: [ 9187]: <-- [9:AT+FBO=0\r]
Oct 30 17:26:22.19: [ 9187]: --> [2:OK]
Oct 30 17:26:22.19: [ 9187]: <-- [10:AT+FCT=30\r]
Oct 30 17:26:22.39: [ 9187]: --> [2:OK]
Oct 30 17:26:22.39: [ 9187]: <-- [15:AT+FNR=1,1,1,1\r]
Oct 30 17:26:22.59: [ 9187]: --> [2:OK]
Oct 30 17:26:22.59: [ 9187]: <-- [9:AT+FIE=0\r]
Oct 30 17:26:22.79: [ 9187]: --> [2:OK]
Oct 30 17:26:22.79: [ 9187]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 30 17:26:23.04: [ 9187]: --> [2:OK]
Oct 30 17:26:23.04: [ 9187]: <-- [5:ATM1\r]
Oct 30 17:26:23.24: [ 9187]: --> [2:OK]
Oct 30 17:26:23.27: [ 9187]: <-- [14:AT+FCLASS=2.0\r]
Oct 30 17:26:23.54: [ 9187]: --> [2:OK]
Oct 30 17:26:23.54: [ 9187]: <-- [9:AT+FLO=2\r]
Oct 30 17:26:23.84: [ 9187]: --> [2:OK]
Oct 30 17:26:23.84: [ 9187]: <-- [9:AT+FPP=0\r]
Oct 30 17:26:24.14: [ 9187]: --> [2:OK]
Oct 30 17:26:24.14: [ 9187]: <-- [9:AT+FBO=0\r]
Oct 30 17:26:24.44: [ 9187]: --> [2:OK]
Oct 30 17:26:24.44: [ 9187]: <-- [10:AT+FCT=30\r]
Oct 30 17:26:24.74: [ 9187]: --> [2:OK]
Oct 30 17:26:24.74: [ 9187]: <-- [15:AT+FNR=1,1,1,1\r]
Oct 30 17:26:25.04: [ 9187]: --> [2:OK]
Oct 30 17:26:25.04: [ 9187]: <-- [9:AT+FIE=0\r]
Oct 30 17:26:25.35: [ 9187]: --> [2:OK]
Oct 30 17:26:25.35: [ 9187]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Oct 30 17:26:25.69: [ 9187]: --> [2:OK]
Oct 30 17:26:25.69: [ 9187]: <-- [22:AT+FLI="HylaFAX Test"\r]
Oct 30 17:26:26.05: [ 9187]: --> [2:OK]
Oct 30 17:26:26.07: [ 9187]: DIAL 81755
Oct 30 17:26:26.07: [ 9187]: <-- [10:ATDT81755\r]
Oct 30 17:26:38.24: [ 9187]: --> [4:+FCO]
Oct 30 17:26:41.29: [ 9187]: --> [37:+FNF:-^[+FCI:"                    "^T+F]
Oct 30 17:26:41.29: [ 9187]: REMOTE NSF "-^[+FCI:"                    "^T+F"
Oct 30 17:26:41.29: [ 9187]: --> [12:ýÿ¿îWÛÿP5 ]
Oct 30 17:27:21.31: [ 9187]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
Oct 30 17:27:21.31: [ 9187]: SEND FAILED: Unspecified Transmit Phase B error
Oct 30 17:27:21.31: [ 9187]: SEND FAILED: Unspecified Transmit Phase B error; too many attempts to send
Oct 30 17:27:21.31: [ 9187]: <-- [5:ATH0\r]
Oct 30 17:27:21.49: [ 9187]: --> [4:ATH0]
Oct 30 17:27:21.49: [ 9187]: --> [2:OK]
Oct 30 17:27:21.66: [ 9187]: SESSION END

-- 
Steve DuChene              sad@hpuerca.atl.hp.com               1-800-633-3600

	       The HP North American Response Center, Atlanta
		  X/CDE/Vue/xterminal/graphics support team
    		    I am an employee of Hewlett-Packard.