flexfax: Failure to train at 2400 bps or +FMINSP value

[Tobias Richter <tsr@cave.isdn.cs.tu-berlin.de>]

Hi,

I have problems with outbound use of my new MultiTech MT2834ZDXI/0314B.
Most was solved by ugrading to hylafax-v4.0pl2, but this one still
remains:

Your facsimile job to 02319922959 was not sent because:
    Failure to train at 2400 bps or +FMINSP value

    ---- Transcript of session follows ----
Mar 21 02:32:07.20: [25043]: SESSION BEGIN 00000466 492319922959
Mar 21 02:32:07.20: [25043]: SEND FAX: JOB 62 DEST 02319922959 COMMID 00000466
Mar 21 02:32:07.20: [25043]: DELAY 2600 ms
Mar 21 02:32:09.81: [25043]: <-- [17:ATX3E0V1Q0S0=0H0\r]
Mar 21 02:32:10.02: [25043]: --> [16:ATX3E0V1Q0S0=0H0]
Mar 21 02:32:10.02: [25043]: --> [2:OK]
Mar 21 02:32:10.02: [25043]: <-- [21:ATS8=2S7=60&E4&D3&C1\r]
Mar 21 02:32:10.19: [25043]: --> [2:OK]
Mar 21 02:32:10.19: [25043]: <-- [12:AT+FCLASS=2\r]
Mar 21 02:32:10.35: [25043]: --> [2:OK]
Mar 21 02:32:10.35: [25043]: <-- [10:AT+FTBC=0\r]
Mar 21 02:32:10.51: [25043]: --> [2:OK]
Mar 21 02:32:10.51: [25043]: <-- [10:AT+FBOR=0\r]
Mar 21 02:32:10.67: [25043]: --> [2:OK]
Mar 21 02:32:10.67: [25043]: <-- [13:AT+FPHCTO=30\r]
Mar 21 02:32:10.83: [25043]: --> [2:OK]
Mar 21 02:32:10.83: [25043]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Mar 21 02:32:11.00: [25043]: --> [2:OK]
Mar 21 02:32:11.00: [25043]: <-- [7:ATL1M1\r]
Mar 21 02:32:11.16: [25043]: --> [2:OK]
Mar 21 02:32:11.16: [25043]: <-- [12:AT+FCLASS=2\r]
Mar 21 02:32:11.43: [25043]: --> [2:OK]
Mar 21 02:32:11.43: [25043]: <-- [10:AT+FTBC=0\r]
Mar 21 02:32:11.69: [25043]: --> [2:OK]
Mar 21 02:32:11.69: [25043]: <-- [10:AT+FBOR=0\r]
Mar 21 02:32:11.95: [25043]: --> [2:OK]
Mar 21 02:32:11.95: [25043]: <-- [13:AT+FPHCTO=30\r]
Mar 21 02:32:12.21: [25043]: --> [2:OK]
Mar 21 02:32:12.21: [25043]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
Mar 21 02:32:12.48: [25043]: --> [2:OK]
Mar 21 02:32:12.48: [25043]: <-- [26:AT+FLID="+49.30.46507xxx"\r]
Mar 21 02:32:12.76: [25043]: --> [2:OK]
Mar 21 02:32:12.76: [25043]: DIAL 002319922959
Mar 21 02:32:12.76: [25043]: <-- [18:ATDT002319922959@\r]
Mar 21 02:32:25.87: [25043]: --> [5:+FCON]
Mar 21 02:32:28.47: [25043]: --> [27:+FNSF:20 51 06 00 05 00 00 ]
Mar 21 02:32:28.47: [25043]: REMOTE NSF "20 51 06 00 05 00 00"
Mar 21 02:32:28.47: [25043]: --> [28:+FCSI:"MMO-NW 02319922953  "]
Mar 21 02:32:28.48: [25043]: REMOTE CSI "MMO-NW 02319922953"
Mar 21 02:32:28.48: [25043]: --> [21:+FDIS:1,5,0,2,0,0,0,0]
Mar 21 02:32:28.48: [25043]: --> [6:+FPOLL]
Mar 21 02:32:28.48: [25043]: REMOTE has document to POLL
Mar 21 02:32:28.48: [25043]: --> [2:OK]
Mar 21 02:32:28.48: [25043]: REMOTE best rate 14400 bit/s
Mar 21 02:32:28.48: [25043]: REMOTE max page width 1728 pixels in 215 mm
Mar 21 02:32:28.48: [25043]: REMOTE max unlimited page length 
Mar 21 02:32:28.48: [25043]: REMOTE best vres 7.7 line/mm
Mar 21 02:32:28.48: [25043]: REMOTE best format 1-D MR
Mar 21 02:32:28.48: [25043]: REMOTE best 0 ms/scanline
Mar 21 02:32:28.48: [25043]: USE 14400 bit/s
Mar 21 02:32:28.48: [25043]: USE 0 ms/scanline
Mar 21 02:32:28.48: [25043]: SEND file "docq/doc72.ps;00"
Mar 21 02:32:28.54: [25043]: USE page width 1728 pixels in 215 mm
Mar 21 02:32:28.54: [25043]: USE unlimited page length 
Mar 21 02:32:28.54: [25043]: USE 3.85 line/mm
Mar 21 02:32:28.54: [25043]: USE 1-D MR
Mar 21 02:32:28.54: [25043]: <-- [24:AT+FDIS=0,5,0,2,0,0,0,0\r]
Mar 21 02:32:28.87: [25043]: --> [2:OK]
Mar 21 02:32:28.87: [25043]: <-- [7:AT+FDT\r]
Mar 21 02:33:14.72: [25043]: --> [8:+FHNG:27]
Mar 21 02:33:14.72: [25043]: REMOTE HANGUP: Failure to train at 2400 bps or +FMINSP value (code 27)
Mar 21 02:33:15.10: [25043]: --> [2:OK]
Mar 21 02:36:15.06: [25043]: MODEM <Timeout>
Mar 21 02:36:15.06: [25043]: <-- [5:ATH0\r]
Mar 21 02:36:15.32: [25043]: --> [2:OK]
Mar 21 02:36:15.32: [25043]: SESSION END

I get this error repeatedly (same recipient).
This is Linux 2.0.33 using libc.so.5.4.44 and gcc2.7.2 by the way.

Thanks for any help
tobias