get bad page, retrain requested

[Gerd.Prokasky@ska.com (Prokasky)]

Hi!

I am running HylaFAX 4.0pl1 on a Solaris 2.5 platform using a Creatix LC144 VF
modem. I am sending facsimiles through WinHyla Version 0.3b (out of MS Word).

If i send only one Page everything works fine. But sending  two or more pages
causes problems: After sending the first page the modem answers BAD PAGE.

 The send log shows following messages:

May 16 12:10:27.98: [  578]: <-- [9:ATDT2700\r]
May 16 12:10:44.61: [  578]: --> [5:+FCON]
May 16 12:10:46.79: [  578]: --> [29:+FCSI: "     +49 69 75382700"]
May 16 12:10:46.79: [  578]: REMOTE CSI "+49 69 75382700"
May 16 12:10:47.35: [  578]: --> [22:+FDIS: 1,3,0,2,1,0,0,4]
May 16 12:10:47.35: [  578]: --> [2:OK]
May 16 12:10:47.35: [  578]: REMOTE best rate 9600 bit/s
May 16 12:10:47.35: [  578]: REMOTE max page width 1728 pixels in 215 mm
May 16 12:10:47.35: [  578]: REMOTE max unlimited page length
May 16 12:10:47.35: [  578]: REMOTE best vres 7.7 line/mm
May 16 12:10:47.35: [  578]: REMOTE best format 2-D MR
May 16 12:10:47.35: [  578]: REMOTE best 20 ms, 10 ms/scanline
May 16 12:10:47.36: [  578]: USE 9600 bit/s
May 16 12:10:47.36: [  578]: USE 20 ms, 10 ms/scanline
May 16 12:10:47.36: [  578]: SEND file "docq/doc3.ps;40"
May 16 12:10:47.36: [  578]: USE page width 1728 pixels in 215 mm
May 16 12:10:47.36: [  578]: USE unlimited page length
May 16 12:10:47.37: [  578]: USE 3.85 line/mm
May 16 12:10:47.37: [  578]: USE 2-D MR
May 16 12:10:47.37: [  578]: DELAY 200 ms
May 16 12:10:47.57: [  578]: <-- [24:AT+FDIS=0,3,0,2,1,0,0,4\r]
May 16 12:10:47.84: [  578]: --> [2:OK]
May 16 12:10:47.84: [  578]: DELAY 200 ms
May 16 12:10:48.04: [  578]: <-- [7:AT+FDT\r]
May 16 12:10:55.32: [  578]: --> [22:+FDCS: 0,3,0,2,1,0,0,5]
May 16 12:10:55.32: [  578]: --> [7:CONNECT]
May 16 12:10:55.32: [  578]: SEND wait for XON
May 16 12:10:55.32: [  578]: --> [1:^Q]
May 16 12:10:55.32: [  578]: SEND begin page
May 16 12:10:55.33: [  578]: <-- data [1026]
May 16 12:10:55.33: [  578]: <-- data [1031]
May 16 12:10:55.33: [  578]: <-- data [1024]
May 16 12:10:55.33: [  578]: <-- data [1024]
May 16 12:10:55.33: [  578]: <-- data [630]
May 16 12:10:56.41: [  578]: SENT 4726 bytes of data
May 16 12:10:56.41: [  578]: <-- data [2]
May 16 12:10:56.41: [  578]: SEND end page
May 16 12:11:23.09: [  578]: --> [2:OK]
May 16 12:11:23.09: [  578]: SEND send MPS (more pages, same document)
May 16 12:11:23.09: [  578]: DELAY 200 ms
May 16 12:11:23.29: [  578]: <-- [9:AT+FET=0\r]
May 16 12:11:26.72: [  578]: --> [8:+FPTS: 2]
May 16 12:11:26.83: [  578]: --> [2:OK]
May 16 12:11:26.83: [  578]: SEND recv RTN (retrain negative)
May 16 12:11:26.83: [  578]: DELAY 200 ms
May 16 12:11:27.03: [  578]: <-- [7:AT+FDT\r]
May 16 12:11:34.31: [  578]: --> [22:+FDCS: 0,3,0,2,1,0,0,5]
May 16 12:11:34.31: [  578]: --> [7:CONNECT]
May 16 12:11:34.31: [  578]: SEND wait for XON
May 16 12:11:34.31: [  578]: --> [1:^Q]


and so on...

Any idea?

Many thanks for responses

-- 
Gerd Prokasky
Front Office Technical Services (FOTS)

Credit|First
Suisse|Boston

Messeturm
60308 Frankfurt
Germany

Phone: +49 (69) 7538 2641	
Fax  : +49 (69) 7538 2700
email:  gerd.prokasky@ska.com