Re: [hylafax-users] Direct Inward Dial based routing with FaxDispatch

["Suraj Jadhav" <sunracesuraj@xxxxxxxxxxxxxx>]

  Hello,

I did use >ModemReadyCmds: AT*DS1*DD0*DF1*DN3*DP1 - but I do not think USR Fax Modem like this cause server started saying..."The HylaFAX software thinks that there is a problem with the modem on device /dev/ttyS1 that needs attention; repeated attempts to initialize the modem have failed. Consult the server trace logs for more information on what is happening." I do not know what I need to use for USR Fax Modem....is there any place where we can find information about such settings?



You will be notified again after 5 minutes if the problem persists.


On Sun, 21 May 2006 Suraj Jadhav wrote :
>   This sounds great...let me work on this and get back to you....
>
>
>On Sun, 21 May 2006 Aaron Stanford wrote :
> >Suraj,
> >
> >Here's a partial dump of my config.ttySX and FaxDispatch to use as templates:
> >
> >config:
> >
> >ModemType:              Class2.1
> >ModemRate:              57600          # for V.34 faxing
> >ModemNoFlowCmd:        AT&K0
> >ModemSoftFlowCmd:      AT&K4
> >ModemHardFlowCmd:      AT&K3
> >
> >Class2APCmd:            AT+FAP=1,1,1
> >Class2BUGCmd:          AT+FBU=0        # early firmware is buggy
> >Class2SendRTC:          yes
> >Class2UseHex:          yes
> >
> ># Some firmwares do not report copy quality correction, although it
> ># is present and cannot be disabled.  Thus modem-based CQ must be used.
> >Class2CQQueryCmd:      "!(00-02),(00-02)"
> >Class2CQCmd:            AT+FCQ=1,0
> >
> ># versions that respond to AT+FFC=? with non-zero data support RTFCC
> >Class2RTFCC:            yes
> >
> ># unfortunately, HylaFAX can't currently send or receive in color
> ># Also, the modem's extended resolution support is buggy
> >ModemAnswerCmd:        AT+FCC=1,,,,0;A
> >ModemDialCmd:          AT+FCC=1,,,,0;DT%s
> >
> ># If your modem supports ECM you may want to do something like this
> >Class2Cmd:              AT+FCLASS=2.1;+FRY=4
> >
> ># Or with the MT5634ZBA-DID you'll probably need something like...
> >ModemReadyCmds: AT*DS1*DD0*DF1*DN3*DP1  # enable DTMF-DID, wink-start, 3 digits
> >CallIDPattern:  "DTMF"          # format of AT*DF1
> >CallIDAnswerLength:    3              # three DTMF-DID digits then ATA
> >
> >FaxDispatch:
> >
> >case "$CALLID1" in
> >906) SENDTO=djohnson@xxxxxxxxxxx; FILETYPE=pdf;;
> >905) SENDTO=aaron@xxxxxxxxxx; FILETYPE=pdf;;
> >900) SENDTO=jellinger@xxxxxxxxxxx; FILETYPE=pdf;;
> >902) SENDTO=areid@xxxxxxxxxxx; FILETYPE=pdf;;
> >904) SENDTO=bclute@xxxxxxxxxxx; FILETYPE=pdf;;
> >903) SENDTO=jbuckman@xxxxxxxxxxx; FILETYPE=pdf;;
> >901) SENDTO=khardy@xxxxxxxxxxx; FILETYPE=pdf;;
> >esac
> >
> >Hope this helps,
> >Aaron
> >
> >____________________ HylaFAX(tm) Users Mailing List _______________________
> >  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
> >On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
> >  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
> >
>
>
>Thanks & Regards
>Suraj Jadhav

Thanks & Regards
Suraj Jadhav