Hylafax Mailing List Archives

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: [hylafax-users] Sending Errors with 4.2.5

To: "'Raphael BUQUET'" <jraph@xxxxxxxxx>, <hylafax-users@xxxxxxxxxxx>
Subject: Re: [hylafax-users] Sending Errors with 4.2.5
From: "andrew rinaldi" <andrew.rinaldi@xxxxxxxxxxxx>
Reply-to: <andrew.rinaldi@xxxxxxxxxxxx>
Date: Wed, 19 Apr 2006 19:50:07 +0100

Hi Raphael.

Can you tell us which fax machines are at the destinations that fail ?

Regards

ANDREW RINALDI

Mainpine Ltd. Support

USA +1 718 701 2422 | Asia/Europe +44 1225 436137

andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com

From: hylafax-users-bounce@xxxxxxxxxxx [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Raphael BUQUET
Sent: 19 April 2006 18:07
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Sending Errors with 4.2.5

Hello to HylaFAX users !

Abstract (sorry for long post) : Everything works fine and HylaFAX is really great.
My problem is that about 13 % of the faxes cannot get send and finish as failed with always the same errors.
When I send them with our Panasonic Panafax it works on the first try everytime.
Any help would be appreciated - thanks

ERRORS :

* No response to PPS repeated 3 times.; Giving up after 3 attempts to send same page
* Failure to train remote modem at 2400 bps or minimum speed; Giving up after 3 attempts to send same page
* RSRPEC error/got DCN; Giving up after 3 attempts to send same page
* Communication failure during Phase B/C; Giving up after 3 attempts to send same page

I need to send from 250 to 400 faxes a day, with some special days going up to 550.
I have installed a celeron 1.8 Ghz machine with a brand new Debian (Sarge or unstable ?? I don't remenber). I recompiled HylaFAX 4.2.5 from source.
It is working as a mail to fax gateway with 3 modem configured.

There is one Internal Linmodem with Linuxant hsfmodem v7.43.00.01 driver

and 2 external :

Us Robotic Sportster Flash with firmware REV 12.1.0 061663-01/02 - Mise à jour V.90 pour Sportster Flash (11/19/2001)

Olitec Speed'com V92 ready) with firmware V1.700-V90_P21_FSH from the 10/17/2002

The problem is that I often get the 4 same errors when sending faxes to some numbers. I get errors with each of the modems and it is often the sames recipients that creates errors.
Since it is in production (13/04/06) it has sent 1578 faxes, and 206 of them went in errors. So each time I have to print them and send with a "classical" Panafax fax machine.
And everytime here it works from the first time !!

(The rest of the faxes are correctly send -> I am happy because previously I used a Relayfax and got A LOT of SERIOUS problems)

For Some of the errors, it seems that the page (it is essentially one page faxes) is received by distant fax. And HylaFAX think it isn't, so he retries 2 more times.
And after that I have to send another time "by hand" to have the confirmation it has been send (these faxes are important and from the law I have to be sure they have been received).
Sometimes it is then transmitted 4 times, and it happens that people get 2 times all of the products that they ordered in the fax (it is a command).
So I add a warning on the faxes that I send by hand.

I am behind a PABX, but the Panafax is also behind.

My GCC version gcc 3.3.5 (Debian 1:3.3.5-13), libtiff is 3.7.2

SENDFAX command is from a bash script (and works :-)
sendfax -n -s "a4" -t "10" -T "10" -D -R -m -k "now +1 month" -i "Commande ${HEURE}_${MINUTE}_${SECONDE}" -f "${FAX_FROM}" -d "${FAX_NUMBER}" mydoc.pdf

I tried many things from changing when possible the classes of the modem (they are in class 1 or 1.0 when available)
I changed some parameters of sendfax but the problem is still here
I read about timings problems that should be solved in the 4.2.5
And I searched similar problems on the net without finding the right solution.

I saw that there are development releases, should I try them ?

I add the 3 configuration files for the modems and after 4 log of sending that finishes in error.

Many thanks

Raphaël BUQUET
Network Admin and pleased HylaFAX user
jraph@xxxxxxxxx

////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\

Internal modem with Conexant chip, in use with Linuxant driver

# $Id: skel,v 1.5 2004/04/19 18:44:47 lhoward Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:  1
AreaCode:  415
FAXNumber:  01.55.33.60.08
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing:  1
SessionTracing:  11
RecvFileMode:  0600
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 1
SpeakerVolume:  off
GettyArgs:  "-h %l dx_%s"
LocalIdentifier: "CAHPP_cmd1"
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  ""
MaxRecvPages:  25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
#ModemType:  Class1  # use this to supply a hint
ModemRate:  19200  # rate for DCE-DTE communication
ModemFlowControl: rtscts  # RTS/CTS flow control assumed
ModemSetupDTRCmd: AT&D2  # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1  # setup so DCD reflects carrier (or not)
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:  "ATDT0%s,"  # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:  ""  # stuff to do when modem is reset
ModemAnswerCmd:  ATA  # use this to answer phone
ModemNoFlowCmd:  AT&K  # disable flow control cmd
ModemHardFlowCmd: AT&K3  # hardware flow control cmd
ModemSoftFlowCmd: AT&K4  # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0  # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0  # disable command echo
ModemVerboseResultsCmd: ATV1  # enable verbose command results
ModemResultCodesCmd: ATQ0  # enable result codes
ModemOnHookCmd:  ATH0  # place phone on hook (hangup)
ModemSoftResetCmd: ATZ  # do soft reset of modem
ModemWaitTimeCmd: ATS7=60  # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2  # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB  # bit order of received facsimile
ModemSendFillOrder: LSB2MSB  # bit order modem expects for transmit

OLITEC SPEED'COM V92 READY external modem (with 2002 firmware)

#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:  1
AreaCode:  415
FAXNumber:  01.55.33.60.08
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing:  1
SessionTracing:  11
RecvFileMode:  0600
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 1
SpeakerVolume:  off
GettyArgs:  "-h %l dx_%s"
LocalIdentifier: "CAHPP_cmd3"
TagLineFont:  etc/lutRS18.pcf
TagLineFormat:  ""
MaxRecvPages:  25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
#ModemType:  Class1  # use this to supply a hint
ModemRate:  19200  # rate for DCE-DTE communication
ModemFlowControl: xonxoff  # RTS/CTS flow control assumed
ModemSetupDTRCmd: AT&D2  # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1  # setup so DCD reflects carrier (or not)
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:  "ATDT0%s," # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:  ""  # stuff to do when modem is reset
ModemAnswerCmd:  ATA  # use this to answer phone
ModemNoFlowCmd:  AT+IFC=0,0 # disable flow control cmd
ModemHardFlowCmd: AT+IFC=2,2 # hardware flow control cmd
ModemSoftFlowCmd: AT+IFC=1,1 # software flow control cmd
ModemNoAutoAnswerCmd: ATS0=0  # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd: ATE0  # disable command echo
ModemVerboseResultsCmd: ATV1  # enable verbose command results
ModemResultCodesCmd: ATQ0  # enable result codes
ModemOnHookCmd:  ATH0  # place phone on hook (hangup)
ModemSoftResetCmd: ATZ  # do soft reset of modem
ModemWaitTimeCmd: ATS7=60  # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2  # comma pause time is 2 seconds
ModemRecvFillOrder: LSB2MSB  # bit order of received facsimile
ModemSendFillOrder: LSB2MSB  # bit order modem expects for transmit

EXTERNAL MODEM US ROBOTIC SPORSTER FLASH external modem (with 1998 firmware)

# $Id: usr-xon,v 1.11 2005/11/29 21:28:57 lhoward Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
#
# Permission to use, copy, modify, distribute, and sell this software and
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
#
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
#
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
# OF THIS SOFTWARE.
#

#
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and XON/XOFF flow control.
#
#
CountryCode:  1
AreaCode:  415
FAXNumber:  "01.55.33.60.08"
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing:  1
SessionTracing:  1
RecvFileMode:  0600
LogFileMode:  0600
DeviceMode:  0600
RingsBeforeAnswer: 0
SpeakerVolume:  off
GettyArgs:  ""
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:  Class1  # use class 1 interface
ModemRate:  19200  # rate for DCE-DTE communication
ModemDialCmd:  "ATDT0%s,"
ModemFlowControl: xonxoff  # software flow control
#
ModemSetupDTRCmd: ATS13=1&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1  # setup so DCD reflects carrier (or not)
ModemNoFlowCmd:  AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
ModemResultCodesCmd: ATQ0X4  # enable result codes
#
ModemMfrQueryCmd: !USR
ModemModelQueryCmd: ATI3
ModemRevQueryCmd: ATI7  # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:  AT&H0&I0&R1 # setup modem for no flow control
Class1HFLOCmd:  AT&H1&I0&R2 # setup modem for hardware flow control
Class1SFLOCmd:  ""  # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd: AT+FRS=1 # wait after sending TCF for response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd: AT+FCLASS=0 # leave modem idling in class 0
ModemAnswerCmd:  AT+FCLASS=1A # answer in Class 1
#
# When using AT+FRS=n we see USR modems reset themselves in the middle of sessions
# this is not good. So, we seem to work-around that problem by not using the
# command. Unfortunately, this isn't an ideal thing.
#
Class1SwitchingCmd: "<delay\0727>"
ModemResetCmds: ATS40=2

Your facsimile job to 0388980444 failed because:

Communication failure during Phase B/C; Giving up after 3 attempts to send same page

---- Transcript of session follows ----

Apr 19 14:08:09.69: [24812]: SESSION BEGIN 000002131 14150388980444
Apr 19 14:08:09.69: [24812]: HylaFAX (tm) Version 4.2.5
Apr 19 14:08:09.69: [24812]: SEND FAX: JOB 1189 DEST 0388980444 COMMID 000002131 DEVICE '/dev/ttyQ1a2' FROM 'reseaux <reseaux@xxxxxxxx>' USER uucp
Apr 19 14:08:09.69: [24812]: <-- [10:AT+FTBC=0\r]
Apr 19 14:08:09.71: [24812]: --> [2:OK]
Apr 19 14:08:09.71: [24812]: <-- [10:AT+FBOR=0\r]
Apr 19 14:08:09.75: [24812]: --> [2:OK]
Apr 19 14:08:09.75: [24812]: <-- [13:AT+FPHCTO=30\r]
Apr 19 14:08:09.79: [24812]: --> [2:OK]
Apr 19 14:08:09.79: [24812]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Apr 19 14:08:09.83: [24812]: --> [2:OK]
Apr 19 14:08:09.83: [24812]: DIAL 0388980444
Apr 19 14:08:09.83: [24812]: <-- [17:ATDT00388980444,\r]
Apr 19 14:08:34.50: [24812]: --> [5:+FCON]
Apr 19 14:08:36.74: [24812]: --> [29:+FCSI: " 03 88 98 04 44"]
Apr 19 14:08:36.74: [24812]: REMOTE CSI "03 88 98 04 44"
Apr 19 14:08:37.18: [24812]: --> [22:+FDIS: 1,5,0,2,1,0,0,0]
Apr 19 14:08:37.30: [24812]: --> [2:OK]
Apr 19 14:08:37.30: [24812]: REMOTE best rate 14400 bit/s
Apr 19 14:08:37.30: [24812]: REMOTE max A4 page width (215 mm)
Apr 19 14:08:37.30: [24812]: REMOTE max unlimited page length
Apr 19 14:08:37.30: [24812]: REMOTE best vres 7.7 line/mm
Apr 19 14:08:37.30: [24812]: REMOTE format support: MH
Apr 19 14:08:37.30: [24812]: REMOTE best 0 ms/scanline
Apr 19 14:08:37.30: [24812]: USE 14400 bit/s
Apr 19 14:08:37.30: [24812]: SEND file "docq/doc1190.ps;01"
Apr 19 14:08:37.30: [24812]: USE A4 page width (215 mm)
Apr 19 14:08:37.30: [24812]: USE unlimited page length
Apr 19 14:08:37.30: [24812]: USE 7.7 line/mm
Apr 19 14:08:37.30: [24812]: USE 1-D MH
Apr 19 14:08:37.30: [24812]: USE 0 ms/scanline
Apr 19 14:08:37.30: [24812]: <-- [24:AT+FDIS=1,5,0,2,0,0,0,0\r]
Apr 19 14:08:37.34: [24812]: --> [2:OK]
Apr 19 14:08:37.34: [24812]: <-- [7:AT+FDT\r]
Apr 19 14:09:25.33: [24812]: --> [9:+FHNG: 25]
Apr 19 14:09:26.13: [24812]: --> [2:OK]
Apr 19 14:09:26.13: [24812]: <-- [7:AT+FDT\r]
Apr 19 14:09:26.17: [24812]: --> [5:ERROR]
Apr 19 14:09:26.17: [24812]: <-- [6:AT+FK\r]
Apr 19 14:09:26.21: [24812]: --> [5:ERROR]
Apr 19 14:09:26.21: [24812]: MODEM Command error
Apr 19 14:09:26.21: [24812]: SEND: Communication failure during Phase B/C; Giving up after 3 attempts to send same page "docq/doc1190.ps;01", dirnum 0
Apr 19 14:09:26.21: [24812]: <-- [5:ATH0\r]
Apr 19 14:09:26.25: [24812]: --> [2:OK]
Apr 19 14:09:26.25: [24812]: SESSION END

---- Unsent job status ----

Destination: 0388980444
JobID: 1189
GroupID: 1189
Sender: reseaux
Mailaddr: reseaux@xxxxxxxx
CommID: 000002131
Submitted From: localhost.localdomain
Page Width: 209 (mm)
Page Length: 296 (mm)
Resolution: 196 (lpi)
Status: Communication failure during Phase B/C; Giving up after 3 attempts to send same page
Dialogs: 3 (exchanges with remote device)
Dials: 0 (consecutive failed calls to destination)
Calls: 3 (total phone calls placed)
Pages: 0 (pages transmitted)
TotPages: 1 (total pages to transmit)
Attempts: 3 (attempts to send current page)
Dirnum: 0 (directory of next page to send)

---- Documents submitted for transmission ----

The following documents were submitted for transmission and are available on the server for reuse until they are automatically purged when this job is archived. Documents may also be manually removed using the faxrm command; consult faxrm(1) for information.
Filename Size Type
docq/doc1190.ps 3066 PostScript

/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\

Your facsimile job to 0320677663 failed because:

RSRPEC error/got DCN; Giving up after 3 attempts to send same page

---- Transcript of session follows ----

Apr 19 14:26:22.05: [27010]: SESSION BEGIN 000002160 14150320677663
Apr 19 14:26:22.05: [27010]: HylaFAX (tm) Version 4.2.5
Apr 19 14:26:22.05: [27010]: SEND FAX: JOB 1205 DEST 0320677663 COMMID 000002160 DEVICE '/dev/ttySHSF1' FROM 'reseaux <reseaux@xxxxxxxx>' USER uucp
Apr 19 14:26:22.05: [27010]: <-- [14:AT+FCLASS=1.0\r]
Apr 19 14:26:22.07: [27010]: --> [2:OK]
Apr 19 14:26:22.07: [27010]: DIAL 0320677663
Apr 19 14:26:22.07: [27010]: <-- [17:ATDT00320677663,\r]
Apr 19 14:26:44.75: [27010]: --> [7:CONNECT]
Apr 19 14:26:45.90: [27010]: --> [2:OK]
Apr 19 14:26:45.90: [27010]: REMOTE NSF "00 00 25 00 00 00 12 10 6D 02 00 58 00 28 B8 A4 A0 80 91 60"
Apr 19 14:26:45.90: [27010]: NSF remote fax equipment: Ricoh
Apr 19 14:26:45.90: [27010]: <-- [9:AT+FRH=3\r]
Apr 19 14:26:45.93: [27010]: --> [7:CONNECT]
Apr 19 14:26:46.43: [27010]: --> [2:OK] Apr 19 14:26:46.43: [27010]: REMOTE NSF "00 00 25 01 45 4E 49 44 49 52 45 54 53"
Apr 19 14:26:46.43: [27010]: NSF remote fax equipment: Ricoh
Apr 19 14:26:46.43: [27010]: NSF remote station ID: "STERIDINE"
Apr 19 14:26:46.43: [27010]: <-- [9:AT+FRH=3\r]
Apr 19 14:26:46.45: [27010]: --> [7:CONNECT]
Apr 19 14:26:47.13: [27010]: --> [2:OK] Apr 19 14:26:47.13: [27010]: REMOTE CSI "0320677663"
Apr 19 14:26:47.13: [27010]: <-- [9:AT+FRH=3\r]
Apr 19 14:26:47.15: [27010]: --> [7:CONNECT]
Apr 19 14:26:47.55: [27010]: --> [2:OK]
Apr 19 14:26:47.55: [27010]: REMOTE best rate 33600 bit/s
Apr 19 14:26:47.55: [27010]: REMOTE max
A4 page width (215 mm)
Apr 19 14:26:47.55: [27010]: REMOTE max unlimited page length
Apr 19 14:26:47.55: [27010]: REMOTE best vres 200 x 200 dpi
Apr 19 14:26:47.55: [27010]: REMOTE format support: MH, MR, MMR, JBIG
Apr 19 14:26:47.55: [27010]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 19 14:26:47.55: [27010]: REMOTE best 10 ms/scanline
Apr 19 14:26:47.55: [27010]: USE 14400 bit/s
Apr 19 14:26:47.55: [27010]: USE error correction mode
Apr 19 14:26:47.55: [27010]: SEND file "docq/doc1206.ps;41"
Apr 19 14:26:47.55: [27010]: USE A4 page width (215 mm)
Apr 19 14:26:47.55: [27010]: USE unlimited page length
Apr 19 14:26:47.55: [27010]: USE 7.7 line/mm
Apr 19 14:26:47.55: [27010]: USE 2-D MMR
Apr 19 14:26:47.55: [27010]: USE 0 ms/scanline
Apr 19 14:26:47.55: [27010]: SEND training at v.17 14400 bit/s
Apr 19 14:26:47.55: [27010]: <-- [9:AT+FRS=7\r]
Apr 19 14:26:47.80: [27010]: --> [2:OK]
Apr 19 14:26:47.80: [27010]: <-- [9:AT+FTH=3\r]
Apr 19 14:26:48.12: [27010]: --> [7:CONNECT]
Apr 19 14:26:49.69: [27010]: --> [7:CONNECT]
Apr 19 14:26:50.21: [27010]: --> [2:OK]
Apr 19 14:26:50.21: [27010]: <-- [9:AT+FTS=7\r]
Apr 19 14:26:50.36: [27010]: --> [2:OK]
Apr 19 14:26:50.36: [27010]: <-- [11:AT+FTM=145\r]
Apr 19 14:26:50.38: [27010]: --> [7:CONNECT]
Apr 19 14:26:53.58: [27010]: --> [2:OK]
Apr 19 14:26:53.58: [27010]: <-- [9:AT+FRH=3\r]
Apr 19 14:26:54.33: [27010]: --> [7:CONNECT]
Apr 19 14:26:54.88: [27010]: --> [5:ERROR]
Apr 19 14:26:54.88: [27010]: MODEM Command error
Apr 19 14:26:54.88: [27010]: FCS error
Apr 19 14:26:54.88: [27010]: <-- [9:AT+FRS=7\r]
Apr 19 14:26:55.74: [27010]: --> [2:OK]
Apr 19 14:26:55.74: [27010]: <-- [9:AT+FTH=3\r]
Apr 19 14:26:56.06: [27010]: --> [7:CONNECT]
Apr 19 14:26:57.35: [27010]: --> [2:OK]
Apr 19 14:26:57.35: [27010]: SEND send CRP (command repeat)
Apr 19 14:26:57.35: [27010]: <-- [9:AT+FRH=3\r]
Apr 19 14:26:57.98: [27010]: --> [7:CONNECT]
Apr 19 14:26:59.18: [27010]: --> [2:OK]
Apr 19 14:26:59.18: [27010]: TRAINING failed
Apr 19 14:26:59.18: [27010]: The destination appears to have trouble with V.17.
Apr 19 14:26:59.18: [27010]: SEND: RSRPEC error/got DCN; Giving up after 3 attempts to send same page "docq/doc1206.ps;41", dirnum 0
Apr 19 14:26:59.18: [27010]: <-- [9:AT+FTH=3\r]
Apr 19 14:26:59.53: [27010]: --> [7:CONNECT]
Apr 19 14:27:00.82: [27010]: --> [2:OK]
Apr 19 14:27:00.83: [27010]: <-- [5:ATH0\r]
Apr 19 14:27:00.95: [27010]: --> [2:OK]
Apr 19 14:27:00.95: [27010]: SESSION END

---- Unsent job status ----

Destination: 0320677663
JobID: 1205
GroupID: 1205
Sender: reseaux
Mailaddr: reseaux@xxxxxxxx
CommID: 000002160
Submitted From: localhost.localdomain
Page Width: 209 (mm)
Page Length: 296 (mm)
Resolution: 196 (lpi)
Status: RSRPEC error/got DCN; Giving up after 3 attempts to send same page
Dialogs: 3 (exchanges with remote device)
Dials: 0 (consecutive failed calls to destination)
Calls: 3 (total phone calls placed)
Pages: 0 (pages transmitted)
TotPages: 1 (total pages to transmit)
Attempts: 3 (attempts to send current page)
Dirnum: 0 (directory of next page to send)

---- Documents submitted for transmission ----

///////////////////////////////////////////////////////////////////////////////////////////////////////////////
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\

Your facsimile job to 0380447452 failed because:

Failure to train remote modem at 2400 bps or minimum speed; Giving up after 3 attempts to send same page

---- Transcript of session follows ----

Apr 19 14:35:28.65: [27298]: SESSION BEGIN 000002167 14150380447452
Apr 19 14:35:28.65: [27298]: HylaFAX (tm) Version 4.2.5
Apr 19 14:35:28.65: [27298]: SEND FAX: JOB 1209 DEST 0380447452 COMMID 000002167 DEVICE '/dev/ttySHSF1' FROM 'reseaux <reseaux@xxxxxxxx>' USER uucp
Apr 19 14:35:28.65: [27298]: <-- [14:AT+FCLASS=1.0\r]
Apr 19 14:35:28.67: [27298]: --> [2:OK]
Apr 19 14:35:28.67: [27298]: DIAL 0380447452
Apr 19 14:35:28.67: [27298]: <-- [17:ATDT00380447452,\r]
Apr 19 14:35:51.66: [27298]: --> [7:CONNECT]
Apr 19 14:35:53.29: [27298]: --> [2:OK]
Apr 19 14:35:53.29: [27298]: REMOTE NSF "00 00 11 80 00 8A 49 10 55 52 47 4F 20 50 52 45 53 43 52 49 50 54 49 4F 00 67 00 80 80 80 0E 01 01 01 01"
Apr 19 14:35:53.29: [27298]: NSF remote fax equipment: Canon Laser Class 9000 Series
Apr 19 14:35:53.29: [27298]: NSF remote station ID: "URGO PRESCRIPTIO"
Apr 19 14:35:53.29: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:35:53.32: [27298]: --> [7:CONNECT]
Apr 19 14:35:54.01: [27298]: --> [2:OK]
Apr 19 14:35:54.01: [27298]: REMOTE CSI "03 80 44 74 52"
Apr 19 14:35:54.01: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:35:54.03: [27298]: --> [7:CONNECT]
Apr 19 14:35:54.43: [27298]: --> [2:OK]
Apr 19 14:35:54.43: [27298]: REMOTE best rate 33600 bit/s
Apr 19 14:35:54.43: [27298]: REMOTE max A4 page width (215 mm)
Apr 19 14:35:54.43: [27298]: REMOTE max unlimited page length
Apr 19 14:35:54.43: [27298]: REMOTE best vres R16 x 15.4 line/mm
Apr 19 14:35:54.43: [27298]: REMOTE format support: MH, MR, MMR, JBIG
Apr 19 14:35:54.43: [27298]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 19 14:35:54.43: [27298]: REMOTE best 20 ms/scanline
Apr 19 14:35:54.43: [27298]: USE 14400 bit/s
Apr 19 14:35:54.43: [27298]: USE error correction mode
Apr 19 14:35:54.43: [27298]: SEND file "docq/doc1210.ps;01"
Apr 19 14:35:54.43: [27298]: USE A4 page width (215 mm)
Apr 19 14:35:54.43: [27298]: USE unlimited page length
Apr 19 14:35:54.43: [27298]: USE 7.7 line/mm
Apr 19 14:35:54.43: [27298]: USE 2-D MMR
Apr 19 14:35:54.43: [27298]: USE 0 ms/scanline
Apr 19 14:35:54.43: [27298]: SEND training at v.17 14400 bit/s
Apr 19 14:35:54.43: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:35:54.62: [27298]: --> [2:OK]
Apr 19 14:35:54.62: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:35:54.94: [27298]: --> [7:CONNECT]
Apr 19 14:35:56.51: [27298]: --> [7:CONNECT]
Apr 19 14:35:57.03: [27298]: --> [2:OK]
Apr 19 14:35:57.03: [27298]: <-- [9:AT+FTS=7\r]
Apr 19 14:35:57.18: [27298]: --> [2:OK]
Apr 19 14:35:57.18: [27298]: <-- [11:AT+FTM=145\r]
Apr 19 14:35:57.20: [27298]: --> [7:CONNECT]
Apr 19 14:36:00.36: [27298]: --> [2:OK]
Apr 19 14:36:00.36: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:36:00.88: [27298]: --> [7:CONNECT]
Apr 19 14:36:02.14: [27298]: --> [2:OK]
Apr 19 14:36:02.14: [27298]: SEND training at v.17 12000 bit/s
Apr 19 14:36:02.14: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:36:02.33: [27298]: --> [2:OK]
Apr 19 14:36:02.33: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:36:02.65: [27298]: --> [7:CONNECT]
Apr 19 14:36:04.22: [27298]: --> [7:CONNECT]
Apr 19 14:36:04.74: [27298]: --> [2:OK]
Apr 19 14:36:04.74: [27298]: <-- [9:AT+FTS=7\r]
Apr 19 14:36:04.89: [27298]: --> [2:OK]
Apr 19 14:36:04.89: [27298]: <-- [11:AT+FTM=121\r]
Apr 19 14:36:04.91: [27298]: --> [7:CONNECT]
Apr 19 14:36:08.07: [27298]: --> [2:OK]
Apr 19 14:36:08.07: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:36:08.22: [27298]: --> [7:CONNECT]
Apr 19 14:36:08.34: [27298]: --> [5:ERROR]
Apr 19 14:36:08.34: [27298]: MODEM Command error
Apr 19 14:36:08.34: [27298]: FCS error
Apr 19 14:36:08.34: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:36:08.49: [27298]: --> [2:OK]
Apr 19 14:36:08.49: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:36:10.23: [27298]: --> [7:CONNECT]
Apr 19 14:36:11.52: [27298]: --> [2:OK]
Apr 19 14:36:11.52: [27298]: SEND send CRP (command repeat)
Apr 19 14:36:11.52: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:36:14.62: [27298]: --> [0:]
Apr 19 14:36:14.62: [27298]: MODEM <Empty line>
Apr 19 14:36:14.83: [27298]: MODEM <Timeout>
Apr 19 14:36:14.83: [27298]: DELAY 1500 ms
Apr 19 14:36:16.33: [27298]: SEND training at v.17 9600 bit/s
Apr 19 14:36:16.33: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:36:16.45: [27298]: --> [2:OK]
Apr 19 14:36:16.45: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:36:16.77: [27298]: --> [7:CONNECT]
Apr 19 14:36:18.35: [27298]: --> [7:CONNECT]
Apr 19 14:36:18.86: [27298]: --> [2:OK]
Apr 19 14:36:18.86: [27298]: <-- [9:AT+FTS=7\r]
Apr 19 14:36:19.01: [27298]: --> [2:OK]
Apr 19 14:36:19.01: [27298]: <-- [10:AT+FTM=97\r]
Apr 19 14:36:19.03: [27298]: --> [7:CONNECT]
Apr 19 14:36:22.20: [27298]: --> [2:OK]
Apr 19 14:36:22.20: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:36:25.30: [27298]: --> [0:]
Apr 19 14:36:25.30: [27298]: MODEM <Empty line>
Apr 19 14:36:25.50: [27298]: MODEM <Timeout>
Apr 19 14:36:25.50: [27298]: DELAY 1500 ms
Apr 19 14:36:27.00: [27298]: SEND training at v.29 9600 bit/s
Apr 19 14:36:27.00: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:36:27.12: [27298]: --> [2:OK]
Apr 19 14:36:27.12: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:36:27.44: [27298]: --> [7:CONNECT]
Apr 19 14:36:29.02: [27298]: --> [7:CONNECT]
Apr 19 14:36:29.53: [27298]: --> [2:OK]
Apr 19 14:36:29.53: [27298]: <-- [9:AT+FTS=7\r]
Apr 19 14:36:29.68: [27298]: --> [2:OK]
Apr 19 14:36:29.68: [27298]: <-- [10:AT+FTM=96\r]
Apr 19 14:36:29.68: [27298]: --> [7:CONNECT]
Apr 19 14:36:31.71: [27298]: --> [2:OK]
Apr 19 14:36:31.71: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:36:34.81: [27298]: --> [0:]
Apr 19 14:36:34.81: [27298]: MODEM <Empty line>
Apr 19 14:36:35.01: [27298]: MODEM <Timeout>
Apr 19 14:36:35.01: [27298]: DELAY 1500 ms
Apr 19 14:36:36.51: [27298]: SEND training at v.29 7200 bit/s
Apr 19 14:36:36.51: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:36:36.64: [27298]: --> [2:OK]
Apr 19 14:36:36.64: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:36:36.95: [27298]: --> [7:CONNECT]
Apr 19 14:36:38.53: [27298]: --> [7:CONNECT]
Apr 19 14:36:39.04: [27298]: --> [2:OK]
Apr 19 14:36:39.04: [27298]: <-- [9:AT+FTS=7\r]
Apr 19 14:36:39.19: [27298]: --> [2:OK]
Apr 19 14:36:39.19: [27298]: <-- [10:AT+FTM=72\r]
Apr 19 14:36:39.21: [27298]: --> [7:CONNECT]
Apr 19 14:36:41.21: [27298]: --> [2:OK]
Apr 19 14:36:41.21: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:36:41.36: [27298]: --> [7:CONNECT]
Apr 19 14:36:41.49: [27298]: --> [5:ERROR]
Apr 19 14:36:41.49: [27298]: MODEM Command error
Apr 19 14:36:41.49: [27298]: FCS error
Apr 19 14:36:41.49: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:36:41.64: [27298]: --> [2:OK]
Apr 19 14:36:41.64: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:36:41.95: [27298]: --> [7:CONNECT]
Apr 19 14:36:43.24: [27298]: --> [2:OK]
Apr 19 14:36:43.24: [27298]: SEND send CRP (command repeat)
Apr 19 14:36:43.24: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:36:46.34: [27298]: --> [0:]
Apr 19 14:36:46.34: [27298]: MODEM <Empty line>
Apr 19 14:36:46.54: [27298]: MODEM <Timeout>
Apr 19 14:36:46.54: [27298]: DELAY 1500 ms
Apr 19 14:36:48.04: [27298]: SEND training at v.27ter 4800 bit/s
Apr 19 14:36:48.04: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:36:48.17: [27298]: --> [2:OK]
Apr 19 14:36:48.17: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:36:48.49: [27298]: --> [7:CONNECT]
Apr 19 14:36:50.06: [27298]: --> [7:CONNECT]
Apr 19 14:36:50.58: [27298]: --> [2:OK]
Apr 19 14:36:50.58: [27298]: <-- [9:AT+FTS=7\r]
Apr 19 14:36:50.73: [27298]: --> [2:OK]
Apr 19 14:36:50.73: [27298]: <-- [10:AT+FTM=48\r]
Apr 19 14:36:50.73: [27298]: --> [7:CONNECT]
Apr 19 14:36:53.23: [27298]: --> [2:OK]
Apr 19 14:36:53.23: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:36:56.33: [27298]: --> [0:]
Apr 19 14:36:56.33: [27298]: MODEM <Empty line>
Apr 19 14:36:56.54: [27298]: MODEM <Timeout>
Apr 19 14:36:56.54: [27298]: DELAY 1500 ms
Apr 19 14:36:58.04: [27298]: SEND training at v.27ter fallback mode 2400 bit/s
Apr 19 14:36:58.04: [27298]: <-- [9:AT+FRS=7\r]
Apr 19 14:36:58.16: [27298]: --> [2:OK]
Apr 19 14:36:58.16: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:36:58.48: [27298]: --> [7:CONNECT]
Apr 19 14:37:00.05: [27298]: --> [7:CONNECT]
Apr 19 14:37:00.57: [27298]: --> [2:OK]
Apr 19 14:37:00.57: [27298]: <-- [9:AT+FTS=7\r]
Apr 19 14:37:00.72: [27298]: --> [2:OK]
Apr 19 14:37:00.72: [27298]: <-- [10:AT+FTM=24\r]
Apr 19 14:37:00.74: [27298]: --> [7:CONNECT]
Apr 19 14:37:03.46: [27298]: --> [2:OK]
Apr 19 14:37:03.46: [27298]: <-- [9:AT+FRH=3\r]
Apr 19 14:37:06.56: [27298]: --> [0:]
Apr 19 14:37:06.56: [27298]: MODEM <Empty line>
Apr 19 14:37:06.76: [27298]: MODEM <Timeout>
Apr 19 14:37:06.76: [27298]: DELAY 1500 ms
Apr 19 14:37:08.26: [27298]: TRAINING failed
Apr 19 14:37:08.26: [27298]: SEND: Failure to train remote modem at 2400 bps or minimum speed; Giving up after 3 attempts to send same page "docq/doc1210.ps;01", dirnum 0
Apr 19 14:37:08.26: [27298]: <-- [9:AT+FTH=3\r]
Apr 19 14:37:08.58: [27298]: --> [7:CONNECT]
Apr 19 14:37:09.87: [27298]: --> [2:OK]
Apr 19 14:37:09.87: [27298]: <-- [5:ATH0\r]
Apr 19 14:37:09.99: [27298]: --> [2:OK]
Apr 19 14:37:09.99: [27298]: SESSION END

---- Unsent job status ----

Destination: 0380447452
JobID: 1209
GroupID: 1209
Sender: reseaux
Mailaddr: reseaux@xxxxxxxx
CommID: 000002167
Submitted From: localhost.localdomain
Page Width: 209 (mm)
Page Length: 296 (mm)
Resolution: 196 (lpi)
Status: Failure to train remote modem at 2400 bps or minimum speed; Giving up after 3 attempts to send same page
Dialogs: 3 (exchanges with remote device)
Dials: 0 (consecutive failed calls to destination)
Calls: 5 (total phone calls placed)
Pages: 0 (pages transmitted)
TotPages: 1 (total pages to transmit)
Attempts: 3 (attempts to send current page)
Dirnum: 0 (directory of next page to send)

---- Documents submitted for transmission ----

Filename Size Type
docq/doc1210.ps 2917 PostScript

Your facsimile job to 0149380268 failed because:

No response to PPS repeated 3 times.; Giving up after 3 attempts to send same page

---- Transcript of session follows ----

Apr 19 16:06:47.45: [29061]: SESSION BEGIN 000002211 14150149380268
Apr 19 16:06:47.45: [29061]: HylaFAX (tm) Version 4.2.5
Apr 19 16:06:47.45: [29061]: SEND FAX: JOB 1235 DEST 0149380268 COMMID 000002211 DEVICE '/dev/ttySHSF1' FROM 'reseaux <reseaux@xxxxxxxx>' USER uucp
Apr 19 16:06:47.45: [29061]: <-- [14:AT+FCLASS=1.0\r]
Apr 19 16:06:47.47: [29061]: --> [2:OK]
Apr 19 16:06:47.47: [29061]: DIAL 0149380268
Apr 19 16:06:47.47: [29061]: <-- [17:ATDT00149380268,\r]
Apr 19 16:07:06.22: [29061]: --> [7:CONNECT]
Apr 19 16:07:07.80: [29061]: --> [2:OK]
Apr 19 16:07:07.80: [29061]: REMOTE NSF "00 00 11 80 00 8A 49 10 42 49 4F 53 50 48 45 52 45 20 20 20 20 20 20 20 00 56 00 80 80 80 0E 01 01 01"
Apr 19 16:07:07.80: [29061]: NSF remote fax equipment: Canon Laser Class 9000 Series
Apr 19 16:07:07.80: [29061]: NSF remote station ID: "BIOSPHERE "
Apr 19 16:07:07.80: [29061]: <-- [9:AT+FRH=3\r]
Apr 19 16:07:07.82: [29061]: --> [7:CONNECT]
Apr 19 16:07:08.51: [29061]: --> [2:OK]
Apr 19 16:07:08.51: [29061]: REMOTE CSI "0149380268"
Apr 19 16:07:08.51: [29061]: <-- [9:AT+FRH=3\r]
Apr 19 16:07:08.54: [29061]: --> [7:CONNECT]
Apr 19 16:07:09.00: [29061]: --> [2:OK]
Apr 19 16:07:09.00: [29061]: REMOTE best rate 14400 bit/s
Apr 19 16:07:09.00: [29061]: REMOTE max A4 page width (215 mm)
Apr 19 16:07:09.00: [29061]: REMOTE max unlimited page length
Apr 19 16:07:09.00: [29061]: REMOTE best vres R16 x 15.4 line/mm
Apr 19 16:07:09.00: [29061]: REMOTE format support: MH, MR, MMR, JBIG
Apr 19 16:07:09.00: [29061]: REMOTE supports T.30 Annex A, 256-byte ECM
Apr 19 16:07:09.00: [29061]: REMOTE best 10 ms/scanline
Apr 19 16:07:09.00: [29061]: USE 14400 bit/s
Apr 19 16:07:09.00: [29061]: USE error correction mode
Apr 19 16:07:09.00: [29061]: SEND file "docq/doc1236.ps;41"
Apr 19 16:07:09.00: [29061]: USE A4 page width (215 mm)
Apr 19 16:07:09.00: [29061]: USE unlimited page length
Apr 19 16:07:09.00: [29061]: USE 7.7 line/mm
Apr 19 16:07:09.00: [29061]: USE 2-D MMR
Apr 19 16:07:09.00: [29061]: USE 0 ms/scanline
Apr 19 16:07:09.00: [29061]: SEND training at v.17 14400 bit/s
Apr 19 16:07:09.00: [29061]: <-- [9:AT+FRS=7\r]
Apr 19 16:07:09.15: [29061]: --> [2:OK]
Apr 19 16:07:09.15: [29061]: <-- [9:AT+FTH=3\r]
Apr 19 16:07:09.47: [29061]: --> [7:CONNECT]
Apr 19 16:07:11.04: [29061]: --> [7:CONNECT]
Apr 19 16:07:11.56: [29061]: --> [2:OK]
Apr 19 16:07:11.56: [29061]: <-- [9:AT+FTS=7\r]
Apr 19 16:07:11.70: [29061]: --> [2:OK]
Apr 19 16:07:11.70: [29061]: <-- [11:AT+FTM=145\r]
Apr 19 16:07:11.73: [29061]: --> [7:CONNECT]
Apr 19 16:07:14.88: [29061]: --> [2:OK]
Apr 19 16:07:14.88: [29061]: <-- [9:AT+FRH=3\r]
Apr 19 16:07:15.04: [29061]: --> [7:CONNECT]
Apr 19 16:07:16.26: [29061]: --> [2:OK]
Apr 19 16:07:16.26: [29061]: TRAINING succeeded
Apr 19 16:07:16.26: [29061]: SEND begin page
Apr 19 16:07:16.26: [29061]: Reading MR-compressed image file
Apr 19 16:07:16.27: [29061]: SEND EOFB
Apr 19 16:07:16.27: [29061]: SEND send frame number 0
Apr 19 16:07:16.27: [29061]: SEND send frame number 1
Apr 19 16:07:16.27: [29061]: SEND send frame number 2
Apr 19 16:07:16.27: [29061]: SEND send frame number 3
Apr 19 16:07:16.27: [29061]: SEND send frame number 4
Apr 19 16:07:16.27: [29061]: SEND send frame number 5
Apr 19 16:07:16.27: [29061]: SEND send frame number 6
Apr 19 16:07:16.27: [29061]: SEND send frame number 7
Apr 19 16:07:16.27: [29061]: SEND send frame number 8
Apr 19 16:07:16.27: [29061]: SEND send frame number 9
Apr 19 16:07:16.27: [29061]: SEND send frame number 10
Apr 19 16:07:16.27: [29061]: SEND send frame number 11
Apr 19 16:07:16.27: [29061]: SEND send frame number 12
Apr 19 16:07:16.27: [29061]: SEND send frame number 13
Apr 19 16:07:16.27: [29061]: SEND send frame number 14
Apr 19 16:07:16.28: [29061]: SEND send frame number 15
Apr 19 16:07:16.28: [29061]: SEND send frame number 16
Apr 19 16:07:16.28: [29061]: SEND send frame number 17
Apr 19 16:07:16.28: [29061]: SEND send frame number 18
Apr 19 16:07:16.28: [29061]: SEND send frame number 19
Apr 19 16:07:16.28: [29061]: SEND send frame number 20
Apr 19 16:07:16.28: [29061]: SEND send frame number 21
Apr 19 16:07:16.28: [29061]: SEND send frame number 22
Apr 19 16:07:16.28: [29061]: SEND send frame number 23
Apr 19 16:07:16.28: [29061]: SEND send frame number 24
Apr 19 16:07:16.28: [29061]: SEND send frame number 25
Apr 19 16:07:16.28: [29061]: SEND send frame number 26
Apr 19 16:07:16.28: [29061]: SEND send frame number 27
Apr 19 16:07:16.28: [29061]: SEND send frame number 28
Apr 19 16:07:16.28: [29061]: SEND send frame number 29
Apr 19 16:07:16.28: [29061]: SEND send frame number 30
Apr 19 16:07:16.28: [29061]: SEND send frame number 31
Apr 19 16:07:16.28: [29061]: SEND send frame number 32
Apr 19 16:07:16.28: [29061]: SEND send frame number 33
Apr 19 16:07:16.28: [29061]: SEND send frame number 34
Apr 19 16:07:16.28: [29061]: SEND send frame number 35
Apr 19 16:07:16.28: [29061]: SEND send frame number 36
Apr 19 16:07:16.28: [29061]: SEND send frame number 37
Apr 19 16:07:16.28: [29061]: SEND send frame number 38
Apr 19 16:07:16.28: [29061]: SEND send frame number 39
Apr 19 16:07:16.28: [29061]: SEND send frame number 40
Apr 19 16:07:16.28: [29061]: SEND send frame number 41
Apr 19 16:07:16.28: [29061]: SEND send frame number 42
Apr 19 16:07:16.28: [29061]: SEND send frame number 43
Apr 19 16:07:16.28: [29061]: SEND send frame number 44
Apr 19 16:07:16.28: [29061]: DELAY 200 ms
Apr 19 16:07:16.48: [29061]: <-- [11:AT+FTM=146\r]
Apr 19 16:07:16.80: [29061]: --> [7:CONNECT]
Apr 19 16:07:24.35: [29061]: --> [2:OK]
Apr 19 16:07:24.35: [29061]: <-- [9:AT+FTS=9\r]
Apr 19 16:07:24.52: [29061]: --> [2:OK]
Apr 19 16:07:24.52: [29061]: <-- [9:AT+FTH=3\r]
Apr 19 16:07:24.54: [29061]: --> [7:CONNECT]
Apr 19 16:07:25.92: [29061]: --> [2:OK]
Apr 19 16:07:25.92: [29061]: SEND send PPS (partial page signal)
Apr 19 16:07:25.92: [29061]: SEND send EOP (no more pages or documents)
Apr 19 16:07:25.92: [29061]: <-- [9:AT+FRH=3\r]
Apr 19 16:07:26.07: [29061]: --> [7:CONNECT]
Apr 19 16:07:26.19: [29061]: --> [5:ERROR]
Apr 19 16:07:26.19: [29061]: MODEM Command error
Apr 19 16:07:26.19: [29061]: FCS error
Apr 19 16:07:26.19: [29061]: <-- [9:AT+FRS=7\r]
Apr 19 16:07:26.33: [29061]: --> [2:OK]
Apr 19 16:07:26.33: [29061]: <-- [9:AT+FTH=3\r]
Apr 19 16:07:28.05: [29061]: --> [7:CONNECT]
Apr 19 16:07:29.34: [29061]: --> [2:OK]
Apr 19 16:07:29.34: [29061]: SEND send CRP (command repeat)
Apr 19 16:07:29.34: [29061]: <-- [9:AT+FRH=3\r]
Apr 19 16:07:32.44: [29061]: --> [0:]
Apr 19 16:07:32.44: [29061]: MODEM <Empty line>
Apr 19 16:07:32.64: [29061]: MODEM <Timeout>
Apr 19 16:07:32.64: [29061]: <-- [9:AT+FTH=3\r]
Apr 19 16:07:32.96: [29061]: --> [7:CONNECT]
Apr 19 16:07:34.36: [29061]: --> [2:OK]
Apr 19 16:07:34.36: [29061]: SEND send PPS (partial page signal)
Apr 19 16:07:34.36: [29061]: SEND send EOP (no more pages or documents)
Apr 19 16:07:34.36: [29061]: <-- [9:AT+FRH=3\r]
Apr 19 16:07:34.51: [29061]: --> [7:CONNECT]
Apr 19 16:07:34.63: [29061]: --> [5:ERROR]
Apr 19 16:07:34.63: [29061]: MODEM Command error
Apr 19 16:07:34.63: [29061]: FCS error
Apr 19 16:07:34.63: [29061]: <-- [9:AT+FRS=7\r]
Apr 19 16:07:34.77: [29061]: --> [2:OK]
Apr 19 16:07:34.77: [29061]: <-- [9:AT+FTH=3\r]
Apr 19 16:07:35.09: [29061]: --> [7:CONNECT]
Apr 19 16:07:36.39: [29061]: --> [2:OK]
Apr 19 16:07:36.39: [29061]: SEND send CRP (command repeat)
Apr 19 16:07:36.39: [29061]: <-- [9:AT+FRH=3\r]
Apr 19 16:07:39.49: [29061]: --> [0:]
Apr 19 16:07:39.49: [29061]: MODEM <Empty line>
Apr 19 16:07:39.69: [29061]: MODEM <Timeout>
Apr 19 16:07:39.69: [29061]: <-- [9:AT+FTH=3\r]
Apr 19 16:07:40.00: [29061]: --> [7:CONNECT]
Apr 19 16:07:41.41: [29061]: --> [2:OK]
Apr 19 16:07:41.41: [29061]: SEND send PPS (partial page signal)
Apr 19 16:07:41.41: [29061]: SEND send EOP (no more pages or documents)
Apr 19 16:07:41.41: [29061]: <-- [9:AT+FRH=3\r]
Apr 19 16:07:44.51: [29061]: --> [0:]
Apr 19 16:07:44.51: [29061]: MODEM <Empty line>
Apr 19 16:07:44.71: [29061]: MODEM <Timeout>
Apr 19 16:07:44.71: [29061]: No response to PPS repeated 3 times.
Apr 19 16:07:44.71: [29061]: SEND end page
Apr 19 16:07:44.71: [29061]: SEND: No response to PPS repeated 3 times.; Giving up after 3 attempts to send same page "docq/doc1236.ps;41", dirnum 0
Apr 19 16:07:44.71: [29061]: <-- [9:AT+FTH=3\r]
Apr 19 16:07:45.03: [29061]: --> [7:CONNECT]
Apr 19 16:07:46.32: [29061]: --> [2:OK]
Apr 19 16:07:46.32: [29061]: <-- [5:ATH0\r]
Apr 19 16:07:46.45: [29061]: --> [2:OK]
Apr 19 16:07:46.45: [29061]: SESSION END

---- Unsent job status ----

Destination: 0149380268
JobID: 1235
GroupID: 1235
Sender: reseaux
Mailaddr: reseaux@xxxxxxxx
CommID: 000002211
Submitted From: localhost.localdomain
Page Width: 209 (mm)
Page Length: 296 (mm)
Resolution: 196 (lpi)
Status: No response to PPS repeated 3 times.; Giving up after 3 attempts to send same page
Dialogs: 3 (exchanges with remote device)
Dials: 0 (consecutive failed calls to destination)
Calls: 3 (total phone calls placed)
Pages: 0 (pages transmitted)
TotPages: 1 (total pages to transmit)
Attempts: 3 (attempts to send current page)
Dirnum: 0 (directory of next page to send)

---- Documents submitted for transmission ----

The following documents were submitted for transmission and are available on the server for reuse until they are automatically purged when this job is removed. Documents may also be manually removed using the faxrm command; consult faxrm(1) for information.

Filename Size Type

docq/doc1236.ps 2699 PostScript

Prev by Date: Re: [hylafax-users] 4.2.5: non ecm sending sessions logged at smaller chunks
Next by Date: [hylafax-users] issues with killtime and timeofday
Previous by thread: Re: [hylafax-users] Blocked by concurrent cal
Next by thread: [hylafax-users] issues with killtime and timeofday
Index(es):
- Main
- Thread

Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services