|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Rockforce Quadro+ - 1 port hangs
Hi Anton.
What happens if you power cycle the server ?
Regards
ANDREW RINALDI
Mainpine Support
USA +1 718 701 2422 | Asia/Europe +44 1225 436137
andrew.rinaldi@xxxxxxxxxxxx | www.mainpine.com
-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Anton Karpov
Sent: 03 February 2006 11:24
To: hylafax-users@xxxxxxxxxxx
Subject: [hylafax-users] Rockforce Quadro+ - 1 port hangs
Hello
I have Rockforce Quadro+ working with 4 ports configured for
Hylafax+faxgetty incoming only.
Hylafax 4.2.5 on Gentoo, Kernel 2.6.14.1 For about 3 days everything worked
fine , then port #1 ( ttyS4) hung .
The rest of the ports work fine.
If I restart faxgetty I get "Waiting for the modem to come ready" and then
"Initializing server" on port 1, while 3 other ports are "Running and idle"
Right when the port #1 hung there is an unusual log.
Right after this log the port #1 does not respond anymore, while port #2 ,
3, 4 work fine.
Could anyone tell me if this a hardware or software issue?
Feb 02 10:05:25.21: [ 8085]: SESSION BEGIN 000000125 19529282279 Feb 02
10:05:25.21: [ 8085]: HylaFAX (tm) Version 4.2.5 Feb 02 10:05:25.21: [
8085]: <-- [4:ATA\r] Feb 02 10:05:37.99: [ 8085]: --> [7:CONNECT] Feb 02
10:05:37.99: [ 8085]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS4'
Feb 02 10:05:37.99: [ 8085]: RECV FAX: begin Feb 02 10:05:37.99: [ 8085]:
<-- data [32] Feb 02 10:05:37.99: [ 8085]: <-- data [2] Feb 02 10:05:38.00:
[ 8085]: --> [7:CONNECT] Feb 02 10:05:38.00: [ 8085]: <-- data [23] Feb 02
10:05:38.00: [ 8085]: <-- data [2] Feb 02 10:05:38.00: [ 8085]: -->
[7:CONNECT] Feb 02 10:05:38.00: [ 8085]: <-- data [13] Feb 02 10:05:38.00: [
8085]: <-- data [2] Feb 02 10:05:40.22: [ 8085]: --> [2:OK] Feb 02
10:05:40.22: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02 10:05:40.60: [ 8085]: -->
[7:CONNECT] Feb 02 10:05:42.22: [ 8085]: --> [2:OK] Feb 02 10:05:42.22: [
8085]: REMOTE TSI "7153590948"
Feb 02 10:05:42.22: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02 10:05:42.24: [ 8085]:
--> [7:CONNECT] Feb 02 10:05:42.61: [ 8085]: --> [2:OK] Feb 02 10:05:42.61:
[ 8085]: REMOTE wants 14400 bit/s Feb 02 10:05:42.61: [ 8085]: REMOTE wants
A4 page width (215 mm) Feb 02 10:05:42.61: [ 8085]: REMOTE wants unlimited
page length Feb 02 10:05:42.61: [ 8085]: REMOTE wants 7.7 line/mm Feb 02
10:05:42.61: [ 8085]: REMOTE wants 1-D MH Feb 02 10:05:42.61: [ 8085]: RECV
training at v.17 14400 bit/s Feb 02 10:05:42.61: [ 8085]: <--
[11:AT+FRM=145\r] Feb 02 10:05:44.23: [ 8085]: --> [7:CONNECT] Feb 02
10:05:45.70: [ 8085]: RECV: TCF 2656 bytes, 6% non-zero, 823 zero-run Feb 02
10:05:45.70: [ 8085]: RECV: reject TCF (zero run too short, min 1800) Feb 02
10:05:45.70: [ 8085]: --> [10:NO CARRIER] Feb 02 10:05:45.70: [ 8085]: <--
[9:AT+FRS=7\r] Feb 02 10:05:45.78: [ 8085]: --> [2:OK] Feb 02 10:05:45.78: [
8085]: <-- [9:AT+FTH=3\r] Feb 02 10:05:46.64: [ 8085]: --> [7:CONNECT] Feb
02 10:05:46.64: [ 8085]: <-- data [3] Feb 02 10:05:46.64: [ 8085]: <-- data
[2] Feb 02 10:05:46.97: [ 8085]: --> [2:OK] Feb 02 10:05:46.97: [ 8085]:
TRAINING failed Feb 02 10:05:46.97: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02
10:05:47.31: [ 8085]: --> [7:CONNECT] Feb 02 10:05:48.60: [ 8085]: -->
[10:NO CARRIER] Feb 02 10:05:48.60: [ 8085]: MODEM No carrier Feb 02
10:05:48.60: [ 8085]: <-- [9:AT+FRS=7\r] Feb 02 10:05:48.68: [ 8085]: -->
[2:OK] Feb 02 10:05:48.68: [ 8085]: <-- [9:AT+FTH=3\r] Feb 02 10:05:49.54: [
8085]: --> [7:CONNECT] Feb 02 10:05:49.54: [ 8085]: <-- data [3] Feb 02
10:05:49.54: [ 8085]: <-- data [2] Feb 02 10:05:49.86: [ 8085]: --> [2:OK]
Feb 02 10:05:49.86: [ 8085]: RECV send CRP (command repeat) Feb 02
10:05:49.86: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02 10:05:50.32: [ 8085]: -->
[7:CONNECT] Feb 02 10:05:51.59: [ 8085]: --> [10:NO CARRIER] Feb 02
10:05:51.59: [ 8085]: MODEM No carrier Feb 02 10:05:51.59: [ 8085]: <--
[9:AT+FRS=7\r] Feb 02 10:05:51.67: [ 8085]: --> [2:OK] Feb 02 10:05:51.67: [
8085]: <-- [9:AT+FTH=3\r] Feb 02 10:05:52.54: [ 8085]: --> [7:CONNECT] Feb
02 10:05:52.54: [ 8085]: <-- data [3] Feb 02 10:05:52.54: [ 8085]: <-- data
[2] Feb 02 10:05:52.86: [ 8085]: --> [2:OK] Feb 02 10:05:52.86: [ 8085]:
RECV send CRP (command repeat) Feb 02 10:05:52.86: [ 8085]: <--
[9:AT+FRH=3\r] Feb 02 10:05:59.86: [ 8085]: --> [0:] Feb 02 10:05:59.86: [
8085]: MODEM <Empty line> Feb 02 10:05:59.86: [ 8085]: <-- data [1] Feb 02
10:05:59.87: [ 8085]: --> [2:] Feb 02 10:05:59.87: [ 8085]: --> [2:OK] Feb
02 10:05:59.87: [ 8085]: DELAY 1500 ms Feb 02 10:06:01.37: [ 8085]: <--
[9:AT+FTH=3\r] Feb 02 10:06:02.23: [ 8085]: --> [7:CONNECT] Feb 02
10:06:02.23: [ 8085]: <-- data [32] Feb 02 10:06:02.23: [ 8085]: <-- data
[2] Feb 02 10:06:02.24: [ 8085]: --> [7:CONNECT] Feb 02 10:06:02.24: [
8085]: <-- data [23] Feb 02 10:06:02.24: [ 8085]: <-- data [2] Feb 02
10:06:02.24: [ 8085]: --> [7:CONNECT] Feb 02 10:06:02.24: [ 8085]: <-- data
[13] Feb 02 10:06:02.24: [ 8085]: <-- data [2] Feb 02 10:06:04.46: [ 8085]:
--> [2:OK] Feb 02 10:06:04.46: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02
10:06:11.47: [ 8085]: --> [0:] Feb 02 10:06:11.47: [ 8085]: MODEM <Empty
line> Feb 02 10:06:11.47: [ 8085]: <-- data [1] Feb 02 10:06:11.48: [ 8085]:
--> [2:] Feb 02 10:06:11.48: [ 8085]: --> [2:OK] Feb 02 10:06:11.48: [
8085]: DELAY 1500 ms Feb 02 10:06:12.98: [ 8085]: <-- [9:AT+FTH=3\r] Feb 02
10:06:13.84: [ 8085]: --> [7:CONNECT] Feb 02 10:06:13.84: [ 8085]: <-- data
[32] Feb 02 10:06:13.84: [ 8085]: <-- data [2] Feb 02 10:06:13.85: [ 8085]:
--> [7:CONNECT] Feb 02 10:06:13.85: [ 8085]: <-- data [23] Feb 02
10:06:13.85: [ 8085]: <-- data [2] Feb 02 10:06:13.85: [ 8085]: -->
[7:CONNECT] Feb 02 10:06:13.85: [ 8085]: <-- data [13] Feb 02 10:06:13.85: [
8085]: <-- data [2] Feb 02 10:06:16.07: [ 8085]: --> [2:OK] Feb 02
10:06:16.07: [ 8085]: <-- [9:AT+FRH=3\r] Feb 02 10:06:23.08: [ 8085]: -->
[0:] Feb 02 10:06:23.08: [ 8085]: MODEM <Empty line> Feb 02 10:06:23.08: [
8085]: <-- data [1] Feb 02 10:06:23.09: [ 8085]: --> [2:] Feb 02
10:06:23.09: [ 8085]: --> [2:OK] Feb 02 10:06:23.09: [ 8085]: RECV FAX:
Failure to train modems Feb 02 10:06:23.09: [ 8085]: RECV FAX: end Feb 02
10:06:23.09: [ 8085]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
