|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] Rockforce Quadro+ - 1 port hangs
Hello
I have Rockforce Quadro+ working with 4 ports configured for
Hylafax+faxgetty incoming only.
Hylafax 4.2.5 on Gentoo, Kernel 2.6.14.1
For about 3 days everything worked fine , then port #1 ( ttyS4) hung .
The rest of the ports work fine.
If I restart faxgetty I get "Waiting for the modem to come ready" and
then "Initializing server" on port 1, while 3 other ports are "Running
and idle"
Right when the port #1 hung there is an unusual log.
Right after this log the port #1 does not respond anymore, while port #2
, 3, 4 work fine.
Could anyone tell me if this a hardware or software issue?
Feb 02 10:05:25.21: [ 8085]: SESSION BEGIN 000000125 19529282279
Feb 02 10:05:25.21: [ 8085]: HylaFAX (tm) Version 4.2.5
Feb 02 10:05:25.21: [ 8085]: <-- [4:ATA\r]
Feb 02 10:05:37.99: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:37.99: [ 8085]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS4'
Feb 02 10:05:37.99: [ 8085]: RECV FAX: begin
Feb 02 10:05:37.99: [ 8085]: <-- data [32]
Feb 02 10:05:37.99: [ 8085]: <-- data [2]
Feb 02 10:05:38.00: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:38.00: [ 8085]: <-- data [23]
Feb 02 10:05:38.00: [ 8085]: <-- data [2]
Feb 02 10:05:38.00: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:38.00: [ 8085]: <-- data [13]
Feb 02 10:05:38.00: [ 8085]: <-- data [2]
Feb 02 10:05:40.22: [ 8085]: --> [2:OK]
Feb 02 10:05:40.22: [ 8085]: <-- [9:AT+FRH=3\r]
Feb 02 10:05:40.60: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:42.22: [ 8085]: --> [2:OK]
Feb 02 10:05:42.22: [ 8085]: REMOTE TSI "7153590948"
Feb 02 10:05:42.22: [ 8085]: <-- [9:AT+FRH=3\r]
Feb 02 10:05:42.24: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:42.61: [ 8085]: --> [2:OK]
Feb 02 10:05:42.61: [ 8085]: REMOTE wants 14400 bit/s
Feb 02 10:05:42.61: [ 8085]: REMOTE wants A4 page width (215 mm)
Feb 02 10:05:42.61: [ 8085]: REMOTE wants unlimited page length
Feb 02 10:05:42.61: [ 8085]: REMOTE wants 7.7 line/mm
Feb 02 10:05:42.61: [ 8085]: REMOTE wants 1-D MH
Feb 02 10:05:42.61: [ 8085]: RECV training at v.17 14400 bit/s
Feb 02 10:05:42.61: [ 8085]: <-- [11:AT+FRM=145\r]
Feb 02 10:05:44.23: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:45.70: [ 8085]: RECV: TCF 2656 bytes, 6% non-zero, 823 zero-run
Feb 02 10:05:45.70: [ 8085]: RECV: reject TCF (zero run too short, min 1800)
Feb 02 10:05:45.70: [ 8085]: --> [10:NO CARRIER]
Feb 02 10:05:45.70: [ 8085]: <-- [9:AT+FRS=7\r]
Feb 02 10:05:45.78: [ 8085]: --> [2:OK]
Feb 02 10:05:45.78: [ 8085]: <-- [9:AT+FTH=3\r]
Feb 02 10:05:46.64: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:46.64: [ 8085]: <-- data [3]
Feb 02 10:05:46.64: [ 8085]: <-- data [2]
Feb 02 10:05:46.97: [ 8085]: --> [2:OK]
Feb 02 10:05:46.97: [ 8085]: TRAINING failed
Feb 02 10:05:46.97: [ 8085]: <-- [9:AT+FRH=3\r]
Feb 02 10:05:47.31: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:48.60: [ 8085]: --> [10:NO CARRIER]
Feb 02 10:05:48.60: [ 8085]: MODEM No carrier
Feb 02 10:05:48.60: [ 8085]: <-- [9:AT+FRS=7\r]
Feb 02 10:05:48.68: [ 8085]: --> [2:OK]
Feb 02 10:05:48.68: [ 8085]: <-- [9:AT+FTH=3\r]
Feb 02 10:05:49.54: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:49.54: [ 8085]: <-- data [3]
Feb 02 10:05:49.54: [ 8085]: <-- data [2]
Feb 02 10:05:49.86: [ 8085]: --> [2:OK]
Feb 02 10:05:49.86: [ 8085]: RECV send CRP (command repeat)
Feb 02 10:05:49.86: [ 8085]: <-- [9:AT+FRH=3\r]
Feb 02 10:05:50.32: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:51.59: [ 8085]: --> [10:NO CARRIER]
Feb 02 10:05:51.59: [ 8085]: MODEM No carrier
Feb 02 10:05:51.59: [ 8085]: <-- [9:AT+FRS=7\r]
Feb 02 10:05:51.67: [ 8085]: --> [2:OK]
Feb 02 10:05:51.67: [ 8085]: <-- [9:AT+FTH=3\r]
Feb 02 10:05:52.54: [ 8085]: --> [7:CONNECT]
Feb 02 10:05:52.54: [ 8085]: <-- data [3]
Feb 02 10:05:52.54: [ 8085]: <-- data [2]
Feb 02 10:05:52.86: [ 8085]: --> [2:OK]
Feb 02 10:05:52.86: [ 8085]: RECV send CRP (command repeat)
Feb 02 10:05:52.86: [ 8085]: <-- [9:AT+FRH=3\r]
Feb 02 10:05:59.86: [ 8085]: --> [0:]
Feb 02 10:05:59.86: [ 8085]: MODEM <Empty line>
Feb 02 10:05:59.86: [ 8085]: <-- data [1]
Feb 02 10:05:59.87: [ 8085]: --> [2:]
Feb 02 10:05:59.87: [ 8085]: --> [2:OK]
Feb 02 10:05:59.87: [ 8085]: DELAY 1500 ms
Feb 02 10:06:01.37: [ 8085]: <-- [9:AT+FTH=3\r]
Feb 02 10:06:02.23: [ 8085]: --> [7:CONNECT]
Feb 02 10:06:02.23: [ 8085]: <-- data [32]
Feb 02 10:06:02.23: [ 8085]: <-- data [2]
Feb 02 10:06:02.24: [ 8085]: --> [7:CONNECT]
Feb 02 10:06:02.24: [ 8085]: <-- data [23]
Feb 02 10:06:02.24: [ 8085]: <-- data [2]
Feb 02 10:06:02.24: [ 8085]: --> [7:CONNECT]
Feb 02 10:06:02.24: [ 8085]: <-- data [13]
Feb 02 10:06:02.24: [ 8085]: <-- data [2]
Feb 02 10:06:04.46: [ 8085]: --> [2:OK]
Feb 02 10:06:04.46: [ 8085]: <-- [9:AT+FRH=3\r]
Feb 02 10:06:11.47: [ 8085]: --> [0:]
Feb 02 10:06:11.47: [ 8085]: MODEM <Empty line>
Feb 02 10:06:11.47: [ 8085]: <-- data [1]
Feb 02 10:06:11.48: [ 8085]: --> [2:]
Feb 02 10:06:11.48: [ 8085]: --> [2:OK]
Feb 02 10:06:11.48: [ 8085]: DELAY 1500 ms
Feb 02 10:06:12.98: [ 8085]: <-- [9:AT+FTH=3\r]
Feb 02 10:06:13.84: [ 8085]: --> [7:CONNECT]
Feb 02 10:06:13.84: [ 8085]: <-- data [32]
Feb 02 10:06:13.84: [ 8085]: <-- data [2]
Feb 02 10:06:13.85: [ 8085]: --> [7:CONNECT]
Feb 02 10:06:13.85: [ 8085]: <-- data [23]
Feb 02 10:06:13.85: [ 8085]: <-- data [2]
Feb 02 10:06:13.85: [ 8085]: --> [7:CONNECT]
Feb 02 10:06:13.85: [ 8085]: <-- data [13]
Feb 02 10:06:13.85: [ 8085]: <-- data [2]
Feb 02 10:06:16.07: [ 8085]: --> [2:OK]
Feb 02 10:06:16.07: [ 8085]: <-- [9:AT+FRH=3\r]
Feb 02 10:06:23.08: [ 8085]: --> [0:]
Feb 02 10:06:23.08: [ 8085]: MODEM <Empty line>
Feb 02 10:06:23.08: [ 8085]: <-- data [1]
Feb 02 10:06:23.09: [ 8085]: --> [2:]
Feb 02 10:06:23.09: [ 8085]: --> [2:OK]
Feb 02 10:06:23.09: [ 8085]: RECV FAX: Failure to train modems
Feb 02 10:06:23.09: [ 8085]: RECV FAX: end
Feb 02 10:06:23.09: [ 8085]: SESSION END
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
