[hylafax-users] Error following AT+FDT command

[erich.iseli@xxxxxxxxxxxxxxxx]

Title: Error following AT+FDT command

Hello,

We're using Hylafax 4.2.0 and have a problem when sending our faxes to a customer running newly a Xerox WorkCenter 3545.

When sending [7:AT+FDT\r] it's going quite a while until the fax answers with
[7:+FHS:1B]
[2:OK]

It looks as this is not what Hylafax is expecting, so it's sending the FDT command again and the answer it gets is
[5:ERROR]

What is the problem here?

I'm attaching one of the logfiles showing that error.

Erich

 

<<c000044675.txt>>

Okt 14 17:54:21.24: [25094]: SESSION BEGIN 000044675 4171xxxxxxx
Okt 14 17:54:21.24: [25094]: HylaFAX (tm) Version 4.2.0
Okt 14 17:54:21.24: [25094]: SEND FAX: JOB 38170 DEST 071xxxxxxx COMMID 000044675 DEVICE '/dev/ttyS0'
Okt 14 17:54:21.24: [25094]: <-- [9:AT+FLO=1\r]
Okt 14 17:54:21.39: [25094]: --> [2:OK]
Okt 14 17:54:21.39: [25094]: <-- [9:AT+FPP=0\r]
Okt 14 17:54:21.53: [25094]: --> [2:OK]
Okt 14 17:54:21.53: [25094]: <-- [9:AT+FBO=0\r]
Okt 14 17:54:21.66: [25094]: --> [2:OK]
Okt 14 17:54:21.66: [25094]: <-- [10:AT+FCT=30\r]
Okt 14 17:54:21.80: [25094]: --> [2:OK]
Okt 14 17:54:21.80: [25094]: <-- [15:AT+FNR=1,1,1,1\r]
Okt 14 17:54:21.95: [25094]: --> [2:OK]
Okt 14 17:54:21.95: [25094]: <-- [9:AT+FIE=0\r]
Okt 14 17:54:22.09: [25094]: --> [2:OK]
Okt 14 17:54:22.09: [25094]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Okt 14 17:54:22.24: [25094]: --> [2:OK]
Okt 14 17:54:22.24: [25094]: DIAL 071xxxxxxx
Okt 14 17:54:22.24: [25094]: <-- [15:ATDT071xxxxxxx\r]
Okt 14 17:54:30.91: [25094]: --> [4:+FCO]
Okt 14 17:54:32.95: [25094]: --> [27:+FCI:"    +41 71 xxx xx xx"]
Okt 14 17:54:32.95: [25094]: REMOTE CSI "+41 71 xxx xx xx"
Okt 14 17:54:32.95: [25094]: --> [20:+FIS:1,5,2,2,1,1,0,0]
Okt 14 17:54:32.95: [25094]: --> [2:OK]
Okt 14 17:54:32.95: [25094]: REMOTE best rate 14400 bit/s
Okt 14 17:54:32.95: [25094]: REMOTE max A3 page width (303 mm)
Okt 14 17:54:32.95: [25094]: REMOTE max unlimited page length
Okt 14 17:54:32.95: [25094]: REMOTE best vres 7.7 line/mm
Okt 14 17:54:32.95: [25094]: REMOTE best format 2-D MR
Okt 14 17:54:32.95: [25094]: REMOTE supports T.30 Annex A, 256-byte ECM
Okt 14 17:54:32.95: [25094]: REMOTE best 0 ms/scanline
Okt 14 17:54:32.95: [25094]: USE 14400 bit/s
Okt 14 17:54:32.95: [25094]: USE 0 ms/scanline
Okt 14 17:54:32.95: [25094]: SEND file "docq/doc38170.ps;00"
Okt 14 17:54:32.95: [25094]: USE A4 page width (215 mm)
Okt 14 17:54:32.95: [25094]: USE unlimited page length
Okt 14 17:54:32.95: [25094]: USE 3.85 line/mm
Okt 14 17:54:32.95: [25094]: USE 1-D MH
Okt 14 17:54:32.95: [25094]: <-- [23:AT+FIS=0,5,0,2,0,0,0,0\r]
Okt 14 17:54:33.08: [25094]: --> [2:OK]
Okt 14 17:54:33.08: [25094]: <-- [7:AT+FDT\r]
Okt 14 17:55:28.42: [25094]: --> [7:+FHS:1B]
Okt 14 17:55:29.72: [25094]: --> [2:OK]
Okt 14 17:55:29.72: [25094]: <-- [7:AT+FDT\r]
Okt 14 17:55:29.85: [25094]: --> [5:ERROR]
Okt 14 17:55:29.85: [25094]: <-- [7:AT+FKS\r]
Okt 14 17:55:29.98: [25094]: --> [2:OK]
Okt 14 17:55:29.98: [25094]: <-- [5:ATH0\r]
Okt 14 17:55:30.11: [25094]: --> [2:OK]
Okt 14 17:55:30.11: [25094]: SESSION END