Re: [hylafax-users] problems with faxrcvd

["Ricardo Albuquerque" <rsouza@xxxxxxxxxxxxxxxxxxx>]

I realy don't know....

Below is the content of my config.ttyS1 file:

Thanks in advance

Ricardo





CountryCode:
AreaCode:
FAXNumber:              +55.85.3266.9283
LongDistancePrefix:     0
InternationalPrefix:    0
DialStringRules:        etc/dialrules
ServerTracing:          527
SessionTracing:         527
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0666
RingsBeforeAnswer:      3
SpeakerVolume:          HIGH
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "Informatica SVM"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use class 2.0 interface
ModemRate:              19200           # DCE-DTE communication rate
ModemFlowControl:       rtscts          # hardware flow control
#
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow 
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow 
control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or 
not)
ModemResultCodesCmd:    ATQ0X4          # enable extended result codes
#
# NB: adaptive answer only seems to work properly when
#     the modem is left idling in Class 2.0
#
ModemSetupAACmd:        AT+FAA=0
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATM1 ATM1 ATM1 ATM1"
#
# Modem does not support HDLC frame tracing; we add this just
# to eliminate spurious ERROR results that confuse the naive.
#
Class2BUGCmd:           AT+FBU=0
#
# The modem doesn't support copy quality checking, even though it
# returns (0-2,0-2) for AT+FCQ=?; therefore we override the query
# response so that the server will do copy quality checking.
#
Class2CQQueryCmd:       !(0),(0)        # override modem response
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0
#
# USR modems violate Class 2.0 specs and do not send RTC itself
#
Class2SendRTC:  yes
#
# +FAP=? not supported on this modem, gives ERROR in ServerTracing
#
Class2APQueryCmd:       none












----- Original Message ----- 
From: "Mark Ratering" <techsupport@xxxxxxxxxxxxxx>
To: "Ricardo Albuquerque" <rsouza@xxxxxxxxxxxxxxxxxxx>
Cc: <hylafax-users@xxxxxxxxxxx>
Sent: Friday, August 26, 2005 2:55 PM
Subject: Re: [hylafax-users] problems with faxrcvd


> Ricardo Albuquerque wrote:
>
> > Hi all,
> >  I'm trying to route all the inconming faxes to users mailboxes. 
> > Analising the log in /var/log/messages, I noticed that process FaxGetty 
> > are not sending the parameters "CIDNumber" and "CIDName". See the log 
> > below, the 3 last parameters are empty.
> >  Aug 26 15:04:06 oraserver FaxGetty[5133]: ANSWER: FAX CONNECTION  DEVICE 
> > '/dev/ttyS1'
> > Aug 26 15:04:34 oraserver FaxGetty[6820]: RECV FAX (000000050): from 
> > 8532669797, page 1 in 0:26, INF, 3.85 line/mm, 1-D MH, 9600 bit/s
> > Aug 26 15:04:34 oraserver FaxGetty[6821]: RECV FAX (000000050): 
> > recvq/fax000000007.tif from 8532669797, route to <unspecified>, 1 pages 
> > in 0:28
> > Aug 26 15:04:37 oraserver FaxGetty[5133]: RECV FAX: bin/faxrcvd 
> > "recvq/fax000000007.tif" "ttyS1" "000000050" "" "" ""
> >  In fact, I need the value of the variable $SENDER, to set the $SENDTO, 
> > in the script /etc/FaxDispatch.
> >  Any clues?
> >  Thanks in advance
> >  Ricardo Albuquerque
>
>
> Do you have your config.TTYSxx set up correctly?
>
> ____________________ HylaFAX(tm) Users Mailing List 
> _______________________
>  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*