|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
(no subject)
Hi,
after years of smooth operation I had to install a new modem to our
hylafax server and as I had no problems with hylafax in years I
seem to be a little helpless ...
The new modem is the Devolo MicroLink 65k Fun II (the best I could
get around the corner). After my earlier mail I got a working config
file mailed, but I still have a problem with receiving faxes:
The resulting tif-file shows only scrambled lines. Like you have
normally only some if the line is bad. Any hint where I could look?
Below I have attached a copy of the log and the config file.
Thank your very much for your help. To get the server back running is
the last thing I need to do before I can start my two week holiday!
Harald
log/00000547
> Jul 21 15:59:15.85: [ 2044]: SESSION BEGIN 00000547 49228000000
> Jul 21 15:59:15.85: [ 2044]: HylaFAX (tm) Version 4.1.8
> Jul 21 15:59:15.85: [ 2044]: <-- [4:ATA\r]
> Jul 21 15:59:21.19: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:21.19: [ 2044]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
> Jul 21 15:59:21.19: [ 2044]: MODEM input buffering enabled
> Jul 21 15:59:21.19: [ 2044]: RECV FAX: begin
> Jul 21 15:59:21.19: [ 2044]: RECV FAX: CDPN
> Jul 21 15:59:21.20: [ 2044]: MODEM input buffering disabled
> Jul 21 15:59:21.20: [ 2044]: <-- HDLC<23:FF C0 02 86 B6 4E 96 62 04 A6 76 96 A6 B2 04 04 04 04 04 04 04 04 04>
> Jul 21 15:59:21.20: [ 2044]: <-- data [23]
> Jul 21 15:59:21.20: [ 2044]: <-- data [2]
> Jul 21 15:59:22.08: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:22.08: [ 2044]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
> Jul 21 15:59:22.08: [ 2044]: <-- data [10]
> Jul 21 15:59:22.08: [ 2044]: <-- data [2]
> Jul 21 15:59:23.21: [ 2044]: --> [2:OK]
> Jul 21 15:59:23.21: [ 2044]: <-- [9:AT+FRH=3\r]
> Jul 21 15:59:23.52: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:25.03: [ 2044]: --> HDLC<25:FF C0 C2 9C EC CC 6C CC 1C 9C 1C 4C 4C 0C 04 04 04 04 04 04 04 04 04 49 5F>
> Jul 21 15:59:25.03: [ 2044]: --> [2:OK]
> Jul 21 15:59:25.03: [ 2044]: REMOTE TSI "02289836379"
> Jul 21 15:59:25.03: [ 2044]: <-- [9:AT+FRH=3\r]
> Jul 21 15:59:25.04: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:25.38: [ 2044]: --> HDLC<12:FF C8 C1 00 45 1F 01 01 01 00 CC D3>
> Jul 21 15:59:25.38: [ 2044]: --> [2:OK]
> Jul 21 15:59:25.38: [ 2044]: REMOTE wants 14400 bit/s
> Jul 21 15:59:25.38: [ 2044]: REMOTE wants page width 1728 pixels in 215 mm
> Jul 21 15:59:25.38: [ 2044]: REMOTE wants unlimited page length
> Jul 21 15:59:25.38: [ 2044]: REMOTE wants 3.85 line/mm
> Jul 21 15:59:25.38: [ 2044]: REMOTE wants 2-D MR
> Jul 21 15:59:25.38: [ 2044]: RECV training at v.17 14400 bit/s
> Jul 21 15:59:25.38: [ 2044]: <-- [11:AT+FRM=145\r]
> Jul 21 15:59:27.14: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:28.70: [ 2044]: RECV: TCF 2744 bytes, 1% non-zero, 2702 zero-run
> Jul 21 15:59:28.70: [ 2044]: --> [10:NO CARRIER]
> Jul 21 15:59:28.70: [ 2044]: DELAY 75 ms
> Jul 21 15:59:28.77: [ 2044]: TRAINING succeeded
> Jul 21 15:59:28.77: [ 2044]: <-- [9:AT+FTH=3\r]
> Jul 21 15:59:28.83: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:28.83: [ 2044]: <-- HDLC<3:FF C8 21>
> Jul 21 15:59:28.83: [ 2044]: <-- data [3]
> Jul 21 15:59:28.83: [ 2044]: <-- data [2]
> Jul 21 15:59:30.08: [ 2044]: --> [2:OK]
> Jul 21 15:59:30.08: [ 2044]: MODEM input buffering enabled
> Jul 21 15:59:30.08: [ 2044]: <-- [11:AT+FRM=146\r]
> Jul 21 15:59:31.02: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:31.02: [ 2044]: RECV: begin page
> Jul 21 15:59:45.44: [ 2044]: RECV: 1115 total lines, 0 bad lines, 0 consecutive bad lines
> Jul 21 15:59:45.44: [ 2044]: RECV: end page
> Jul 21 15:59:45.44: [ 2044]: --> [10:NO CARRIER]
> Jul 21 15:59:45.44: [ 2044]: MODEM input buffering disabled
> Jul 21 15:59:45.44: [ 2044]: <-- [9:AT+FRH=3\r]
> Jul 21 15:59:45.74: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:46.53: [ 2044]: --> HDLC<5:FF C8 F4 CC 66>
> Jul 21 15:59:46.53: [ 2044]: --> [2:OK]
> Jul 21 15:59:46.53: [ 2044]: RECV recv EOP (no more pages or documents)
> Jul 21 15:59:46.53: [ 2044]: DELAY 70 ms
> Jul 21 15:59:46.60: [ 2044]: <-- [9:AT+FTH=3\r]
> Jul 21 15:59:46.71: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:46.71: [ 2044]: <-- HDLC<3:FF C8 31>
> Jul 21 15:59:46.71: [ 2044]: <-- data [3]
> Jul 21 15:59:46.71: [ 2044]: <-- data [2]
> Jul 21 15:59:47.95: [ 2044]: --> [2:OK]
> Jul 21 15:59:47.95: [ 2044]: RECV send MCF (message confirmation)
> Jul 21 15:59:47.96: [ 2044]: RECV FAX (00000547): from 02289836379, page 1 in 0:19, INF, 3.85 line/mm, 2-D MR, 14400 bit/s
> Jul 21 15:59:47.96: [ 2044]: RECV FAX (00000547): recvq/fax00489.tif from 02289836379, route to <unspecified>, 1 pages in 0:26
> Jul 21 15:59:47.97: [ 2044]: <-- [9:AT+FRH=3\r]
> Jul 21 15:59:48.24: [ 2044]: --> [7:CONNECT]
> Jul 21 15:59:49.22: [ 2044]: --> HDLC<5:FF C8 DF 59 6F>
> Jul 21 15:59:49.22: [ 2044]: --> [2:OK]
> Jul 21 15:59:49.22: [ 2044]: MODEM input buffering enabled
> Jul 21 15:59:49.22: [ 2044]: RECV FAX: bin/faxrcvd "recvq/fax00489.tif" "ttyS0" "00000547" "" "" "" ""
> Jul 21 15:59:49.96: [ 2044]: RECV FAX: end
> Jul 21 15:59:50.01: [ 2044]: SESSION END
etc/config.ttyS0
> # $Id: class1,v 1.12 2002/08/21 16:01:07 darren Exp $
> #
> # HylaFAX Facsimile Software
> #
> # Config File fuer Devolo Microlink 56k fun II
> #
> # Copyright (c) 1990-1996 Sam Leffler
> # Copyright (c) 1991-1996 Silicon Graphics, Inc.
> # HylaFAX is a trademark of Silicon Graphics, Inc.
> #
> # Permission to use, copy, modify, distribute, and sell this software and
> # its documentation for any purpose is hereby granted without fee, provided
> # that (i) the above copyright notices and this permission notice appear in
> # all copies of the software and related documentation, and (ii) the names of
> # Sam Leffler and Silicon Graphics may not be used in any advertising or
> # publicity relating to the software without the specific, prior written
> # permission of Sam Leffler and Silicon Graphics.
> #
> # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
> # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
> # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
> #
> # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
> # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
> # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
> # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
> # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
> # OF THIS SOFTWARE.
> #
>
> #
> # Generic Class 1 modem configuration.
> #
> # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
> #
> CountryCode: 49
> AreaCode: 0228
> FAXNumber: +49.228.000000
> LongDistancePrefix: 0
> InternationalPrefix: 00
> DialStringRules: "etc/dialrules"
> ServerTracing: 0
> SessionTracing: 0xff
> RecvFileMode: 0644
> LogFileMode: 0600
> DeviceMode: 0600
> RingsBeforeAnswer: 1
> SpeakerVolume: off
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: "Meine Firma"
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: " Von %%n %%l|%c|Seite %%p von %%t"
> PercentGoodLines: 90
> MaxConsecutiveBadLines: 10
> MaxRecvPages: 25
> WedgedCmd: bin/wedged
> FaxRcvdCmd: bin/faxrcvd
> NotifyCmd: bin/notify
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> # HINWEIS:
> # Falls das Modem nicht waehlt, wartet es auf Freizeichen
> # Abhilfe: Mit minicom connecten und dann
> # ATE1, ATQ0, ATX3 AT&W
> # damit der Kasten sich das merken tut
> ModemType: Class1 # use this to supply a hint
> ModemRate: 57600 # lock rate for DCE-DTE communication
> ModemFlowControl: rtscts # default
> ModemResetCmds: "ATZ ATX3 ATS0=2"
> # Die Commands von der Hylafaxliste
> # mit denen auch brother-faxe funktionieren sollen
> # AT+MR=0 AT+DR=1 AT+ER=1 AT+ILRR=0
> #ModemResetCmds: "ATZ ATX3 ATS0=2 AT+MR=0 AT+DR=1 AT+ER=1 AT+ILRR=0"
> ModemDialCmd: ATDT0,%s
> Class1Cmd: AT+FCLASS=1 # command to enter class 1
> Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
> Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
> Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
> Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
> Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
> Class1SendMsgDelay: 75 # 75ms delay after training
> #Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
> Class1SwitchingCmd: "<delay:7>"
> Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
> Class1RecvAbortOK: 200 # wait 200ms for abort response
> Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
> Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
> Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
> Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
