|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] HylaFax stops after "SEND begin page"
Does it fail for you on ECM and non-ECM alike, or is it specific to ECM?
Try it with 'sendfax -E'.
Lee.
EISELE Pascal wrote:
Hi Lee,
Here is the output :
find / -name "*libfax*"
/tmp/hylafax-2005-06-12/faxd/libfaxserver.a
/tmp/hylafax-2005-06-12/util/libfaxutil.a
/src/hylafax-4.2.1/util/libfaxutil.a
/src/hylafax-4.2.1/faxd/libfaxserver.a
Nothing intersting, it had been compiled into static. The previous
directories are compilation directories.
What's more ?
Regards
Lee Howard a écrit :
Please send the output of:
find / -name "*libfax*"
Lee.
EISELE Pascal wrote:
I've just build the lasted CVS snapshot (12/06/2005) and it's also
failed.
Is there a way to debug it ?
Here is the new communication log for the sender :
Jun 13 11:45:16.45: [25326]: SESSION BEGIN 000000045 0388657676
Jun 13 11:45:16.45: [25326]: HylaFAX (tm) Version 4.2cvs-2005-06-12
Jun 13 11:45:16.45: [25326]: SEND FAX: JOB 33 DEST 00388657676
COMMID 000000045 DEVICE '/dev/cua/a'
Jun 13 11:45:16.45: [25326]: <-- [12:AT+FCLASS=1\r]
Jun 13 11:45:16.48: [25326]: --> [2:OK]
Jun 13 11:45:16.51: [25326]: DIAL 00388657676
Jun 13 11:45:16.51: [25326]: <-- [16:ATDT00388657676\r]
Jun 13 11:45:30.11: [25326]: --> [7:CONNECT]
Jun 13 11:45:31.79: [25326]: --> [2:OK]
Jun 13 11:45:31.79: [25326]: REMOTE NSF "B5 00 AA 48 79 6C 61 46 41
58 20 28 74 6D 29 20 56 65 72 73 69 6F 6E 20 34 2E 32 2E 31"
Jun 13 11:45:31.79: [25326]: NSF remote fax equipment: HylaFAX
Jun 13 11:45:31.80: [25326]: NSF remote station ID: "HylaFAX (tm)
Version 4.2.1"
Jun 13 11:45:31.80: [25326]: <-- [9:AT+FRH=3\r]
Jun 13 11:45:31.81: [25326]: --> [7:CONNECT]
Jun 13 11:45:32.62: [25326]: --> [2:OK]
Jun 13 11:45:32.62: [25326]: REMOTE CSI "Appligos"
Jun 13 11:45:32.62: [25326]: <-- [9:AT+FRH=3\r]
Jun 13 11:45:32.64: [25326]: --> [7:CONNECT]
Jun 13 11:45:33.10: [25326]: --> [2:OK]
Jun 13 11:45:33.10: [25326]: REMOTE best rate 14400 bit/s
Jun 13 11:45:33.10: [25326]: REMOTE max A3 page width (303 mm)
Jun 13 11:45:33.10: [25326]: REMOTE max unlimited page length
Jun 13 11:45:33.10: [25326]: REMOTE best vres R16 x 15.4 line/mm
Jun 13 11:45:33.10: [25326]: REMOTE best format 2-D MMR
Jun 13 11:45:33.10: [25326]: REMOTE supports T.30 Annex A, 256-byte ECM
Jun 13 11:45:33.10: [25326]: REMOTE best 0 ms/scanline
Jun 13 11:45:33.11: [25326]: USE 14400 bit/s
Jun 13 11:45:33.11: [25326]: USE error correction mode
Jun 13 11:45:33.11: [25326]: SEND file "docq/doc103.ps;c0"
Jun 13 11:45:33.11: [25326]: USE A4 page width (215 mm)
Jun 13 11:45:33.11: [25326]: USE unlimited page length
Jun 13 11:45:33.11: [25326]: USE 3.85 line/mm
Jun 13 11:45:33.11: [25326]: USE 2-D MMR
Jun 13 11:45:33.11: [25326]: USE 0 ms/scanline
Jun 13 11:45:33.11: [25326]: SEND training at v.17 14400 bit/s
Jun 13 11:45:33.11: [25326]: <-- [9:AT+FTH=3\r]
Jun 13 11:45:33.15: [25326]: --> [7:CONNECT]
Jun 13 11:45:33.15: [25326]: <-- data [23]
Jun 13 11:45:33.15: [25326]: <-- data [2]
Jun 13 11:45:34.94: [25326]: --> [7:CONNECT]
Jun 13 11:45:34.94: [25326]: <-- data [7]
Jun 13 11:45:34.94: [25326]: <-- data [2]
Jun 13 11:45:35.40: [25326]: --> [2:OK]
Jun 13 11:45:35.40: [25326]: <-- [9:AT+FTS=7\r]
Jun 13 11:45:35.49: [25326]: --> [2:OK]
Jun 13 11:45:35.49: [25326]: <-- [11:AT+FTM=145\r]
Jun 13 11:45:35.53: [25326]: --> [7:CONNECT]
Jun 13 11:45:35.53: [25326]: <-- data [1024]
Jun 13 11:45:35.53: [25326]: <-- data [1024]
Jun 13 11:45:35.53: [25326]: <-- data [652]
Jun 13 11:45:35.53: [25326]: <-- data [2]
Jun 13 11:45:38.63: [25326]: --> [2:OK]
Jun 13 11:45:38.64: [25326]: <-- [9:AT+FRH=3\r]
Jun 13 11:45:39.19: [25326]: --> [7:CONNECT]
Jun 13 11:45:40.07: [25326]: --> [2:OK]
Jun 13 11:45:40.07: [25326]: TRAINING succeeded
Jun 13 11:45:40.08: [25326]: SEND begin page
Jun 13 11:45:40.09: [25326]: SEND EOFB
Jun 13 11:45:40.09: [25326]: SEND send frame number 0
Jun 13 11:45:40.09: [25326]: SEND send frame number 1
Jun 13 11:45:40.09: [25326]: SEND send frame number 2
Jun 13 11:45:40.09: [25326]: SEND send frame number 3
Jun 13 11:45:40.09: [25326]: SEND send frame number 4
Jun 13 11:45:40.09: [25326]: SEND send frame number 5
Jun 13 11:45:40.09: [25326]: SEND send frame number 6
Jun 13 11:45:40.09: [25326]: SEND send frame number 7
Jun 13 11:45:40.09: [25326]: SEND send frame number 8
Jun 13 11:45:40.09: [25326]: DELAY 200 ms
Jun 13 11:45:40.30: [25326]: <-- [11:AT+FTM=146\r]
Jun 13 11:45:40.33: [25326]: --> [7:CONNECT]
Jun 13 11:45:40.33: [25326]: <-- data [1028]
Jun 13 11:45:40.33: [25326]: <-- data [1041]
Jun 13 11:45:40.33: [25326]: <-- data [759]
Jun 13 11:45:40.33: [25326]: <-- data [2]
Jun 13 11:45:42.25: [25326]: --> [2:OK]
Jun 13 11:45:42.25: [25326]: <-- [9:AT+FTS=9\r]
Jun 13 11:45:42.35: [25326]: --> [2:OK]
Lee Howard a écrit :
EISELE Pascal wrote:
Jun 09 18:08:28.59: [ 973]: <-- [9:AT+FRH=3\r]
Jun 09 18:08:29.14: [ 973]: --> [7:CONNECT]
Jun 09 18:08:30.03: [ 973]: --> [2:OK]
Jun 09 18:08:30.03: [ 973]: TRAINING succeeded
Jun 09 18:08:30.03: [ 973]: SEND begin page
And here faxsend segfaulted it would seem.
Can you try current HylaFAX CVS HEAD and see if it happens there?
Thanks.
Lee.
____________________ HylaFAX(tm) Users Mailing List
_______________________
To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
/dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
--
EISELE Pascal <mailto:peisele@xxxxxxxxxxx> Direct : +33 (0)3 88 65 76 78
Administrateur systèmes & réseaux Tél : +33 (0)3 88 65 04 04
13b rue du Maréchal Lefebvre Fax : +33 (0)3 88 65 76 76
67100 Strasbourg http://www.appligos.fr <http://www.appligos.fr/>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
