[hylafax-users] T.30 T2 timeout, expected page not received

["Andy Tran" <andy_tran@xxxxxxxxxxxxxxxxx>]

Anyone know what the following error mean or how to fix it? I am using a
USR Sporster 28,800. Thanks.

-Andy


-------------------------------------------------

Status for incoming fax from: +49 69 7928119


    Sender: +49 69 7928119
     Pages: 1
   Quality: Normal
      Page: ISO A4
  Received: 2005:06:03 01:00:43
TimeToRecv: 0:16
SignalRate: 14400 bit/s
DataFormat: 2-D MR
ReceivedOn: ttyS1

The full document was not received because:

    T.30 T2 timeout, expected page not received

    ---- Transcript of session follows ----

Jun 03 01:00:27.16: [ 1833]: SESSION BEGIN 000554552 13105904365
Jun 03 01:00:27.16: [ 1833]: HylaFAX (tm) Version 4.1.8
Jun 03 01:00:27.16: [ 1833]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled Jun 03 01:00:27.16: [ 1833]: <-- [13:AT+FCLASS=1A\r]
Jun 03 01:00:32.44: [ 1833]: --> [7:CONNECT]
Jun 03 01:00:32.44: [ 1833]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS1'
Jun 03 01:00:32.44: [ 1833]: STATE CHANGE: ANSWERING -> RECEIVING
Jun 03 01:00:32.44: [ 1833]: MODEM input buffering enabled
Jun 03 01:00:32.44: [ 1833]: RECV FAX: begin
Jun 03 01:00:32.45: [ 1833]: MODEM input buffering disabled
Jun 03 01:00:32.45: [ 1833]: <-- HDLC<23:FF C0 02 36 2E 76 92 04 34 CE 4E
AE F6 2A 76 86 C6 96 4E A6 B6 82 04> Jun 03 01:00:32.47: [ 1833]: -->
[7:CONNECT]
Jun 03 01:00:32.47: [ 1833]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Jun 03 01:00:34.42: [ 1833]: --> [2:OK]
Jun 03 01:00:34.42: [ 1833]: <-- [9:AT+FRH=3\r]
Jun 03 01:00:35.44: [ 1833]: --> [7:CONNECT]
Jun 03 01:00:36.93: [ 1833]: --> HDLC<25:FF C0 C2 9C 8C 8C 1C 4C 9C EC 04
9C 6C 04 9C 2C D4 04 04 04 04 04 04 39 EC> Jun 03 01:00:36.93: [ 1833]:
--> [2:OK]
Jun 03 01:00:36.93: [ 1833]: REMOTE TSI "+49 69 7928119"
Jun 03 01:00:36.93: [ 1833]: <-- [9:AT+FRH=3\r]
Jun 03 01:00:36.95: [ 1833]: --> [7:CONNECT]
Jun 03 01:00:37.20: [ 1833]: --> HDLC<9:FF C8 C1 00 45 19 00 CE 6D> Jun 03
01:00:37.20: [ 1833]: --> [2:OK]
Jun 03 01:00:37.20: [ 1833]: REMOTE wants 14400 bit/s
Jun 03 01:00:37.20: [ 1833]: REMOTE wants page width 1728 pixels in 215 mm
Jun 03 01:00:37.20: [ 1833]: REMOTE wants unlimited page length
Jun 03 01:00:37.20: [ 1833]: REMOTE wants 3.85 line/mm
Jun 03 01:00:37.20: [ 1833]: REMOTE wants 2-D MR
Jun 03 01:00:37.20: [ 1833]: RECV training at v.17 14400 bit/s
Jun 03 01:00:37.20: [ 1833]: MODEM set XON/XOFF/DRAIN: input ignored,
output generated Jun 03 01:00:37.20: [ 1833]: <-- [11:AT+FRM=145\r]
Jun 03 01:00:38.89: [ 1833]: --> [7:CONNECT]
Jun 03 01:00:40.45: [ 1833]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled Jun 03 01:00:40.45: [ 1833]: RECV: TCF 2811 bytes, 3%
non-zero, 2699 zero-run Jun 03 01:00:40.46: [ 1833]: --> [10:NO CARRIER]
Jun 03 01:00:40.46: [ 1833]: DELAY 75 ms
Jun 03 01:00:40.54: [ 1833]: TRAINING succeeded
Jun 03 01:00:40.54: [ 1833]: <-- [9:AT+FTH=3\r]
Jun 03 01:00:40.74: [ 1833]: --> [7:CONNECT]
Jun 03 01:00:40.74: [ 1833]: <-- HDLC<3:FF C8 21>
Jun 03 01:00:41.92: [ 1833]: --> [2:OK]
Jun 03 01:00:41.92: [ 1833]: MODEM input buffering enabled
Jun 03 01:00:41.92: [ 1833]: MODEM set XON/XOFF/FLUSH: input ignored,
output generated Jun 03 01:00:41.92: [ 1833]: <-- [11:AT+FRM=146\r]
Jun 03 01:00:43.16: [ 1833]: --> [7:CONNECT]
Jun 03 01:00:43.16: [ 1833]: RECV: begin page
Jun 03 01:00:56.00: [ 1833]: RECV/CQ: Bad 1D pixel count, row 1148, got 0,
expected 1728 Jun 03 01:00:56.00: [ 1833]: RECV/CQ: Bad 1D pixel count,
row 1149, got 0, expected 1728 Jun 03 01:00:56.00: [ 1833]: RECV/CQ: Bad
1D pixel count, row 1150, got 0, expected 1728 Jun 03 01:00:56.00: [
1833]: RECV/CQ: Bad 1D pixel count, row 1151, got 0, expected 1728 Jun 03
01:00:56.00: [ 1833]: RECV/CQ: Bad 1D pixel count, row 1152, got 0,
expected 1728 Jun 03 01:00:56.17: [ 1833]: RECV/CQ: Adjusting for RTC
found at row 1147 Jun 03 01:00:56.17: [ 1833]: RECV: 1147 total lines, 0
bad lines, 0 consecutive bad lines Jun 03 01:00:56.17: [ 1833]: RECV: end
page
Jun 03 01:00:56.17: [ 1833]: --> [10:NO CARRIER]
Jun 03 01:00:56.17: [ 1833]: MODEM set XON/XOFF/DRAIN: input ignored,
output disabled Jun 03 01:00:56.17: [ 1833]: MODEM input buffering
disabled
Jun 03 01:00:56.17: [ 1833]: <-- [9:AT+FRH=3\r]
Jun 03 01:00:56.69: [ 1833]: --> [7:CONNECT]
Jun 03 01:01:01.69: [ 1833]: MODEM TIMEOUT: receiving HDLC frame data Jun
03 01:01:01.70: [ 1833]: --> [2:OK]
Jun 03 01:01:01.70: [ 1833]: RECV keeping unconfirmed page
Jun 03 01:01:01.70: [ 1833]: RECV FAX (000554552): from +49 69 7928119,
page 1 in 0:21, INF, 3.85 line/mm, 2-D MR, 14400 bit/s Jun 03 01:01:01.70:
[ 1833]: RECV FAX (000554552): recvq/fax000000147.tif from +49 69 7928119,
route to <unspecified>, 1 pages in 0:29 Jun 03 01:01:01.70: [ 1833]: RECV
FAX: T.30 T2 timeout, expected page not received Jun 03 01:01:01.70: [
1833]: <-- [9:AT+FTH=3\r]
Jun 03 01:01:01.74: [ 1833]: --> [7:CONNECT]
Jun 03 01:01:01.74: [ 1833]: <-- HDLC<3:FF C8 5F>
Jun 03 01:01:02.92: [ 1833]: --> [2:OK]
Jun 03 01:01:02.92: [ 1833]: MODEM input buffering enabled
Jun 03 01:01:02.92: [ 1833]: RECV FAX (000554552): session with +49 69
7928119 terminated abnormally: T.30 T2 timeout, expected page not received
Jun 03 01:01:02.92: [ 1833]: RECV FAX: bin/faxrcvd
"recvq/fax000000147.tif" "ttyS1" "000554552" "T.30 T2 timeout, expected
page not received" "" ""



____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*