[hylafax-users] Fw: can send but cant receive

["-CDRW-" <cdrw.fedora@xxxxxxxxx>]

yes i can send trough cypheus or through sendfax to other faxes but when i
send a fax to the server the reply is blocked by the concurrent and 3 trys
later the reply is blacklisted by modem. When i execute faxstat -s i can 
see
the fax with blacklisted by modem but when i execute faxstat -r is empty.
some ideas?

Yes i have the faxgetty in inittab levels 2345

thx vitor and sorry my bad english i hope u can understand me.

> ----- Original Message ----- 
> From: "Vitor Flausino" <vflausino@xxxxxxxxxxxx>
> To: "-CDRW-" <cdrw.fedora@xxxxxxxxx>; <hylafax-users@xxxxxxxxxxx>
> Sent: Thursday, April 14, 2005 12:40 PM
> Subject: Re: [hylafax-users] can send but cant receive
>
>
> > So you can send but can receive? hummm...
> > Does your box answer? In your /etc/inittab, is faxgetty enabled?
> >
> > -vcf
> > -CDRW- wrote:
> >
> > > Hi, i hope us can help me...
> > >
> > > First of all im going to tell my system, im runnig Hylafax 4.2.1 on
> > > Fedora Core 3 with a BestBuy Modem
> > >
> > > My ttyS0 configuration is:
> > > Generic Class 1 modem configuration
> > > CountryCode:            34
> > > AreaCode:               968
> > > FAXNumber:              201
> > > LongDistancePrefix:     0
> > > InternationalPrefix:    00
> > > DialStringRules:        etc/dialrules.europe
> > > ServerTracing:          1
> > > SessionTracing:         0x4f
> > > RecvFileMode:           0644
> > > LogFileMode:            0644
> > > DeviceMode:             0666
> > > RingsBeforeAnswer:      1
> > > SpeakerVolume:          off
> > > GettyArgs:              "-r -b -s %s %1"
> > > LocalIdentifier:        Empresa
> > > TagLineFont:            etc/lutRS18.pcf
> > > TagLineFormat:          "From %%l|%c|Page %%P of %%T"
> > > QualifyTSI:             etc/tsi
> > > MaxRecvPages:           25
> > > # Modem-related stuff: should reflect modem command interface
> > > # and hardware connection/cabling (e.g. flow control).
> > > ModemType:              Class1          # use this to supply a hint
> > > ModemRate:              19200           # rate for DCE-DTE communication
> > > #ModemFlowControl:      xoff/xon        # XON/XOFF flow control assumed#
> > > #ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
> > > #ModemSetupDCDCmd:      AT&C1           # setup so DCD follows carrier
> > > #GettyArgs:             "-h %l dx_%s"   # modem must auto-detect fax/data
> > >
> > > Class1Cmd:              AT+FCLASS=1     # command to enter class 1
> > > Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before 
> > > PPM
> > > Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before 
> > > TCF
> > > Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before 
> > > EOP
> > > Class1MsgRecvHackCmd:   ""      # command to avoid +FCERROR before image
> > > Class1TCFResponseDelay: 75              # 75ms delay between recv TCF & 
> > > response
> > > Class1SendMsgDelay:     200             # 75ms delay after training
> > > Class1SwitchingCmd:     AT+FRS=7        # silence between HDLC recv and 
> > > trans
> > > Class1TrainingRecovery: 1500            # 1.5sec delay after training 
> > > failure
> > > Class1RecvAbortOK:      200             # wait 200ms for abort response
> > > Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC 
> > > frames
> > > Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident 
> > > frames
> > > Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
> > > Class1TCFMinRun:        1000            # min run is 2/3rds of TCF 
> > > duration
> > >
> > > the rest are #
> > >
> > > First times i reply it the faxstat reply was Blocked by concurrent
> > > call, but later of 3 trys the reply was:
> > >
> > > [ 5403]: SESSION BEGIN 000000101 34968202
> > > Apr 14 11:57:53.98: [ 5403]: HylaFAX (tm) Version 4.2.1
> > > Apr 14 11:57:53.98: [ 5403]: SEND FAX: JOB 40 DEST 202 COMMID
> > > 000000101 DEVICE '/dev/ttyS0'
> > > Apr 14 11:57:53.98: [ 5403]: MODEM input buffering enabled
> > > Apr 14 11:57:53.98: [ 5403]: <-- [12:AT+FCLASS=1\r]
> > > Apr 14 11:57:54.28: [ 5403]: --> [2:OK]
> > > Apr 14 11:57:54.28: [ 5403]: MODEM set XON/XOFF/FLUSH: input ignored,
> > > output disabled
> > > Apr 14 11:57:54.28: [ 5403]: DIAL 202
> > > Apr 14 11:57:54.28: [ 5403]: <-- [8:ATDT202\r]
> > > Apr 14 11:57:54.59: [ 5403]: --> [11:BLACKLISTED]
> > > Apr 14 11:57:54.59: [ 5403]: SEND FAILED: JOB 40 DEST 202 ERR
> > > Blacklisted by modem
> > > Apr 14 11:57:54.59: [ 5403]: <-- [5:ATH0\r]
> > > Apr 14 11:57:54.88: [ 5403]: --> [2:OK]
> > > Apr 14 11:57:54.88: [ 5403]: MODEM set DTR OFF
> > > Apr 14 11:57:54.88: [ 5403]: SESSION END
> > >
> > > can anyone help me?
> > > thx very much and sorry for my bad english :)
> > >
> > > ____________________ HylaFAX(tm) Users Mailing List 
> > > _______________________
> > >  To subscribe/unsubscribe, click 
> > > http://lists.hylafax.org/cgi-bin/lsg2.cgi
> > > On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
> > > /dev/null
> > >  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*