Hi, i hope us can help me...
First of all im going to tell my system, im runnig Hylafax 4.2.1 on
Fedora Core 3 with a BestBuy Modem
My ttyS0 configuration is:
Generic Class 1 modem configuration
CountryCode: 34
AreaCode: 968
FAXNumber: 201
LongDistancePrefix: 0
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
SessionTracing: 0x4f
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0666
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-r -b -s %s %1"
LocalIdentifier: Empresa
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
QualifyTSI: etc/tsi
MaxRecvPages: 25
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
ModemType: Class1 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xoff/xon # XON/XOFF flow control assumed#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image
Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
Class1SendMsgDelay: 200 # 75ms delay after training
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
the rest are #
First times i reply it the faxstat reply was Blocked by concurrent
call, but later of 3 trys the reply was:
[ 5403]: SESSION BEGIN 000000101 34968202
Apr 14 11:57:53.98: [ 5403]: HylaFAX (tm) Version 4.2.1
Apr 14 11:57:53.98: [ 5403]: SEND FAX: JOB 40 DEST 202 COMMID
000000101 DEVICE '/dev/ttyS0'
Apr 14 11:57:53.98: [ 5403]: MODEM input buffering enabled
Apr 14 11:57:53.98: [ 5403]: <-- [12:AT+FCLASS=1\r]
Apr 14 11:57:54.28: [ 5403]: --> [2:OK]
Apr 14 11:57:54.28: [ 5403]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Apr 14 11:57:54.28: [ 5403]: DIAL 202
Apr 14 11:57:54.28: [ 5403]: <-- [8:ATDT202\r]
Apr 14 11:57:54.59: [ 5403]: --> [11:BLACKLISTED]
Apr 14 11:57:54.59: [ 5403]: SEND FAILED: JOB 40 DEST 202 ERR
Blacklisted by modem
Apr 14 11:57:54.59: [ 5403]: <-- [5:ATH0\r]
Apr 14 11:57:54.88: [ 5403]: --> [2:OK]
Apr 14 11:57:54.88: [ 5403]: MODEM set DTR OFF
Apr 14 11:57:54.88: [ 5403]: SESSION END
can anyone help me?
thx very much and sorry for my bad english :)
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
