|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
[hylafax-users] RECV FAX: no answer (T.30 T1 time out)
Hi All,
I have a problem with Hylafax stable version of Debian. It cannot receive
some faxes, with the following error: RECV FAX: no answer (T.30 T1 time out
This error happening usually, when the sender is an older analog fax
machine. I can send fax, and receive fax from other fax servers without any
problem.
Important datas:
Debian Woody
Hylafax version: 1.4.1.3.1 (the latest stable version)
Here are the log of the bad receiving:
Apr 07 12:37:46.44: [ 4993]: SESSION BEGIN 00000044 <phone number>
Apr 07 12:37:46.44: [ 4993]: HylaFAX (tm) Version 4.1.1
Apr 07 12:37:46.44: [ 4993]: MODEM set XON/XOFF/FLUSH: input ignored, output
disabled
Apr 07 12:37:46.44: [ 4993]: <-- [4:ATA\r]
Apr 07 12:37:53.02: [ 4993]: --> [7:CONNECT]
Apr 07 12:37:53.02: [ 4993]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0'
Apr 07 12:37:53.02: [ 4993]: STATE CHANGE: ANSWERING -> RECEIVING
Apr 07 12:37:53.02: [ 4993]: MODEM input buffering enabled
Apr 07 12:37:53.02: [ 4993]: RECV FAX: begin
Apr 07 12:37:53.02: [ 4993]: MODEM input buffering disabled
Apr 07 12:37:53.02: [ 4993]: <-- HDLC<23:FF C0 02 0E AE 2E A6 CA E6 76 96 16
2E F6 72 04 04 04 04 04 04 04 04>
Apr 07 12:37:53.02: [ 4993]: <-- data [23]
Apr 07 12:37:53.02: [ 4993]: <-- data [2]
Apr 07 12:37:54.70: [ 4993]: --> [7:CONNECT]
Apr 07 12:37:54.70: [ 4993]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Apr 07 12:37:54.70: [ 4993]: <-- data [10]
Apr 07 12:37:54.70: [ 4993]: <-- data [2]
Apr 07 12:37:55.24: [ 4993]: --> [2:OK]
Apr 07 12:37:55.24: [ 4993]: <-- [9:AT+FRH=3\r]
Apr 07 12:37:58.34: [ 4993]: --> [0:]
Apr 07 12:37:58.34: [ 4993]: MODEM <Empty line>
Apr 07 12:37:58.34: [ 4993]: MODEM TIMEOUT: waiting for v.21 carrier
Apr 07 12:37:58.34: [ 4993]: <-- data [1]
Apr 07 12:37:58.34: [ 4993]: DELAY 200 ms
Apr 07 12:37:58.54: [ 4993]: MODEM flush i/o
Apr 07 12:37:58.54: [ 4993]: <-- [3:AT\r]
Apr 07 12:37:58.55: [ 4993]: --> [2:OK]
Apr 07 12:37:58.55: [ 4993]: DELAY 1500 ms
Apr 07 12:38:00.05: [ 4993]: <-- [9:AT+FTH=3\r]
Apr 07 12:38:00.10: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:00.10: [ 4993]: <-- HDLC<23:FF C0 02 0E AE 2E A6 CA E6 76 96 16
2E F6 72 04 04 04 04 04 04 04 04>
Apr 07 12:38:00.10: [ 4993]: <-- data [23]
Apr 07 12:38:00.10: [ 4993]: <-- data [2]
Apr 07 12:38:01.89: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:01.89: [ 4993]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Apr 07 12:38:01.89: [ 4993]: <-- data [10]
Apr 07 12:38:01.89: [ 4993]: <-- data [2]
Apr 07 12:38:02.44: [ 4993]: --> [2:OK]
Apr 07 12:38:02.44: [ 4993]: <-- [9:AT+FRH=3\r]
Apr 07 12:38:05.54: [ 4993]: --> [0:]
Apr 07 12:38:05.54: [ 4993]: MODEM <Empty line>
Apr 07 12:38:05.54: [ 4993]: MODEM TIMEOUT: waiting for v.21 carrier
Apr 07 12:38:05.54: [ 4993]: <-- data [1]
Apr 07 12:38:05.54: [ 4993]: DELAY 200 ms
Apr 07 12:38:05.74: [ 4993]: MODEM flush i/o
Apr 07 12:38:05.74: [ 4993]: <-- [3:AT\r]
Apr 07 12:38:05.75: [ 4993]: --> [2:OK]
Apr 07 12:38:05.75: [ 4993]: DELAY 1500 ms
Apr 07 12:38:07.25: [ 4993]: <-- [9:AT+FTH=3\r]
Apr 07 12:38:07.30: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:07.30: [ 4993]: <-- HDLC<23:FF C0 02 0E AE 2E A6 CA E6 76 96 16
2E F6 72 04 04 04 04 04 04 04 04>
Apr 07 12:38:07.30: [ 4993]: <-- data [23]
Apr 07 12:38:07.30: [ 4993]: <-- data [2]
Apr 07 12:38:09.09: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:09.09: [ 4993]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Apr 07 12:38:09.09: [ 4993]: <-- data [10]
Apr 07 12:38:09.09: [ 4993]: <-- data [2]
Apr 07 12:38:09.64: [ 4993]: --> [2:OK]
Apr 07 12:38:09.64: [ 4993]: <-- [9:AT+FRH=3\r]
Apr 07 12:38:12.74: [ 4993]: --> [0:]
Apr 07 12:38:12.74: [ 4993]: MODEM <Empty line>
Apr 07 12:38:12.74: [ 4993]: MODEM TIMEOUT: waiting for v.21 carrier
Apr 07 12:38:12.74: [ 4993]: <-- data [1]
Apr 07 12:38:12.74: [ 4993]: DELAY 200 ms
Apr 07 12:38:12.94: [ 4993]: MODEM flush i/o
Apr 07 12:38:12.94: [ 4993]: <-- [3:AT\r]
Apr 07 12:38:12.95: [ 4993]: --> [2:OK]
Apr 07 12:38:12.95: [ 4993]: DELAY 1500 ms
Apr 07 12:38:14.45: [ 4993]: <-- [9:AT+FTH=3\r]
Apr 07 12:38:14.50: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:14.50: [ 4993]: <-- HDLC<23:FF C0 02 0E AE 2E A6 CA E6 76 96 16
2E F6 72 04 04 04 04 04 04 04 04>
Apr 07 12:38:14.50: [ 4993]: <-- data [23]
Apr 07 12:38:14.50: [ 4993]: <-- data [2]
Apr 07 12:38:16.29: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:16.29: [ 4993]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Apr 07 12:38:16.29: [ 4993]: <-- data [10]
Apr 07 12:38:16.29: [ 4993]: <-- data [2]
Apr 07 12:38:16.84: [ 4993]: --> [2:OK]
Apr 07 12:38:16.84: [ 4993]: <-- [9:AT+FRH=3\r]
Apr 07 12:38:19.94: [ 4993]: --> [0:]
Apr 07 12:38:19.94: [ 4993]: MODEM <Empty line>
Apr 07 12:38:19.94: [ 4993]: MODEM TIMEOUT: waiting for v.21 carrier
Apr 07 12:38:19.94: [ 4993]: <-- data [1]
Apr 07 12:38:19.94: [ 4993]: DELAY 200 ms
Apr 07 12:38:20.14: [ 4993]: MODEM flush i/o
Apr 07 12:38:20.14: [ 4993]: <-- [3:AT\r]
Apr 07 12:38:20.15: [ 4993]: --> [2:OK]
Apr 07 12:38:20.15: [ 4993]: DELAY 1500 ms
Apr 07 12:38:21.65: [ 4993]: <-- [9:AT+FTH=3\r]
Apr 07 12:38:21.70: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:21.70: [ 4993]: <-- HDLC<23:FF C0 02 0E AE 2E A6 CA E6 76 96 16
2E F6 72 04 04 04 04 04 04 04 04>
Apr 07 12:38:21.70: [ 4993]: <-- data [23]
Apr 07 12:38:21.70: [ 4993]: <-- data [2]
Apr 07 12:38:23.49: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:23.49: [ 4993]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Apr 07 12:38:23.49: [ 4993]: <-- data [10]
Apr 07 12:38:23.49: [ 4993]: <-- data [2]
Apr 07 12:38:24.04: [ 4993]: --> [2:OK]
Apr 07 12:38:24.04: [ 4993]: <-- [9:AT+FRH=3\r]
Apr 07 12:38:27.14: [ 4993]: --> [0:]
Apr 07 12:38:27.14: [ 4993]: MODEM <Empty line>
Apr 07 12:38:27.14: [ 4993]: MODEM TIMEOUT: waiting for v.21 carrier
Apr 07 12:38:27.14: [ 4993]: <-- data [1]
Apr 07 12:38:27.14: [ 4993]: DELAY 200 ms
Apr 07 12:38:27.34: [ 4993]: MODEM flush i/o
Apr 07 12:38:27.34: [ 4993]: <-- [3:AT\r]
Apr 07 12:38:27.35: [ 4993]: --> [2:OK]
Apr 07 12:38:27.35: [ 4993]: DELAY 1500 ms
Apr 07 12:38:28.85: [ 4993]: <-- [9:AT+FTH=3\r]
Apr 07 12:38:28.90: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:28.90: [ 4993]: <-- HDLC<23:FF C0 02 0E AE 2E A6 CA E6 76 96 16
2E F6 72 04 04 04 04 04 04 04 04>
Apr 07 12:38:28.90: [ 4993]: <-- data [23]
Apr 07 12:38:28.90: [ 4993]: <-- data [2]
Apr 07 12:38:30.69: [ 4993]: --> [7:CONNECT]
Apr 07 12:38:30.69: [ 4993]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Apr 07 12:38:30.69: [ 4993]: <-- data [10]
Apr 07 12:38:30.69: [ 4993]: <-- data [2]
Apr 07 12:38:31.24: [ 4993]: --> [2:OK]
Apr 07 12:38:31.24: [ 4993]: <-- [9:AT+FRH=3\r]
Apr 07 12:38:34.34: [ 4993]: --> [0:]
Apr 07 12:38:34.34: [ 4993]: MODEM <Empty line>
Apr 07 12:38:34.34: [ 4993]: MODEM TIMEOUT: waiting for v.21 carrier
Apr 07 12:38:34.34: [ 4993]: <-- data [1]
Apr 07 12:38:34.34: [ 4993]: DELAY 200 ms
Apr 07 12:38:34.54: [ 4993]: MODEM flush i/o
Apr 07 12:38:34.54: [ 4993]: <-- [3:AT\r]
Apr 07 12:38:34.55: [ 4993]: --> [2:OK]
Apr 07 12:38:34.55: [ 4993]: RECV FAX: No answer (T.30 T1 timeout)
Apr 07 12:38:34.55: [ 4993]: RECV FAX: end
Apr 07 12:38:34.55: [ 4993]: SESSION END
I am using xon/xoff method, but the rtscts gave the same error. Here is the
config.ttS0:
CountryCode: 36
AreaCode: 1
FAXNumber: <phone number>
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
#ServerTracing: 0x08501
ServerTracing: 0x3
SessionTracing: 0xFFF
RecvFileMode: 0640
LogFileMode: 0640
DeviceMode: 0660
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-r -b %l"
LocalIdentifier: "NothingSetup"
LogFacility: daemon
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
Class1RecvAbortOK: 0
ModemType: Class1 # use this to supply a hint
ModemRate: 38400 # rate for DCE-DTE communication
# ModemFlowControl: rtscts # default
ModemFlowControl: xonxoff # XON/XOFF handshake
#
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
#
ModemDialCmd: ATDT%s # T for tone dialing
I read the mailing list, but I cannot find good solution. If somebody has
any idea, please write.
Thanks a lot
Zsolt
berengere@xxxxxxxxxxx
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
