Re: [hylafax-users] EOP between 2 hylafax server with Multitech 5656 modem

["Emmanuel RIZZI" <erizzi@xxxxxxxxxx>]

Sorry to distrub you again but when i run the faxaddmodem, I get:

> > > > > >
Hmm, this looks like a Class 1 modem.
Product code (ATI0) is "MT5656ZDX".
Other information (ATI3) is "ACF3_V1.702A-V90_P21_FSH".
DTE-DCE flow control scheme [default]?
Modem manufacturer is "Unknown".
Modem model is "Unknown".

Using prototype configuration file class1...

There is no prototype configuration file for your modem, so we will
have to fill in the appropriate parameters by hand.  You will need the
manual for how to program your modem to do this task.  In case you are
uncertain of the meaning of a configuration parameter you should
consult the config(5F) manual page for an explanation.
<<<<<<

I have added the line in the config file as you explained but is there
anything more to do (copying the file somewhere else?)
This is my "/var/spool/hylafax/config/rc288dpi-1 file
> > > > >
#
# Configuration for a Rockwell RC288DPi-based Class 1 modem.
#    Hayes Optima 28800         firmware rev ???
#    Microcom DeskPorte 28.8S   firmware rev V1.100K-V34_DS
#    PPI PM288FXMT              firmware rev 1.57
#
# Note that the modem does not lock the line rate for fax
# receive (at least not the PM288FXMT); but not sure whether
# current flow control settings are maintained or if it
# switches to XON/XOFF (testing host was too fast to see).
#
# CONFIG:CLASS1:28800:.*:.*: Manufacturer=ROCKWELL Model=RC288DPi
# CONFIG:CLASS1:33600:.*:.*: Manufacturer=Rockwell Model=33600
# CONFIG:CLASS1:56000:.*:.*: Manufacturer=Rockwell/Conexant Model=AC/K56
# CONFIG:CLASS1:MT5600ZDX:.*.*: Manufacturer=MultiTech Model=MT5600ZDX
# CONFIG:CLASS1:MT5656ZDX:.*.*: Manufacturer=Multitech Model=MT5656ZDX

# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use this to supply a hint
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&K0           # setup no flow control
ModemHardFlowCmd:       AT&K3           # setup hardware flow control
ModemSoftFlowCmd:       AT&K4           # setup software flow control
ModemSetupDTRCmd:       AT&D2           # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or
not)
#
ModemMfrQueryCmd:       !Rockwell
ModemModelQueryCmd:     !RC288DPi
ModemRevQueryCmd:       ATI3            # product information
#
ModemDialCmd:           ATDT%s          # T for tone dialing
<<<<<<<<



----- Original Message ----- 
From: "Lee Howard" <faxguy@xxxxxxxxxxxxxxxx>
To: "Emmanuel RIZZI" <erizzi@xxxxxxxxxx>
Cc: <hylafax-users@xxxxxxxxxxx>
Sent: Friday, April 01, 2005 8:40 AM
Subject: Re: [hylafax-users] EOP between 2 hylafax server with Multitech
5656 modem


> Emmanuel RIZZI wrote:
>
> > Hmm, this looks like a Class 1 modem.
> > Product code (ATI0) is "MT5656ZDX".
> > Other information (ATI3) is "ACF3_V1.702A-V90_P21_FSH".
> > DTE-DCE flow control scheme [default]?
> > Modem manufacturer is "Unknown".
> > Modem model is "Unknown".
>
> Almost certainly you should be using the "standard" 56K Conexant/Rockwell 
> Class 1 configuration file.  Change the section of 
> /var/spool/hylafax/config/rc288dpi-1 from this:
>
> # CONFIG:CLASS1:28800:.*:.*: Manufacturer=ROCKWELL Model=RC288DPi
> # CONFIG:CLASS1:33600:.*:.*: Manufacturer=Rockwell Model=33600
> # CONFIG:CLASS1:56000:.*:.*: Manufacturer=Rockwell/Conexant Model=AC/K56
> # CONFIG:CLASS1:MT5600ZDX:.*.*: Manufacturer=MultiTech Model=MT5600ZDX
>
> to this:
>
> # CONFIG:CLASS1:28800:.*:.*: Manufacturer=ROCKWELL Model=RC288DPi
> # CONFIG:CLASS1:33600:.*:.*: Manufacturer=Rockwell Model=33600
> # CONFIG:CLASS1:56000:.*:.*: Manufacturer=Rockwell/Conexant Model=AC/K56
> # CONFIG:CLASS1:MT5600ZDX:.*.*: Manufacturer=MultiTech Model=MT5600ZDX
> # CONFIG:CLASS1:MT5656ZDX:.*.*: Manufacturer=MultiTech Model=MT5656ZDX
>
> (adding one line to the bottom).  Then rerun faxaddmodem and choose Class 
> 1.  See how that works.  If it doesn't work, then you should send logs of 
> the initialization sequence (ServerTracing: 0xFFF, logs in 
> /var/log/messages) if it will not initialize, or session logs 
> (SessionTracing: 0xFFF, logs in /var/spool/hylafax/log) if it is an error 
> during the sessions.
>
> Lee.


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*