[hylafax-users] Distinctive Ring.

["Michael Carmody" <michaelc@xxxxxxxxxxxxx>]

Hey All,

Have been using Hylafax for a few years, and have always just unplugged it 
when I did not want it to receive faxes.

I have recently ordered a distinctive ring service to make the fax more 
available to clients. It is turned on and the AT-SDR=6 command has turned 
distinctive ring on my Rockwell modem. Testing with Minicom shows RING2 for 
my normal ring and RING3 for my distinctive ring.

I have added:
Ringfax:                RING3
to my config.ttyS0

and "-SDR=6" to my ModemResetCmds:

Restarted everything and now the neither ring causes faxgetty to answer.

Have pasted in config.ttyS0 below, and I am using hylafax 4.2.1

Thanks for any help you can provide.#
# Generic Class 1.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:            61
AreaCode:               3
FAXNumber:              +61.3.98089982
LongDistancePrefix:     0
InternationalPrefix:    0011
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0666
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
Ringfax:                RING3
SpeakerVolume:          off
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        MikeIT
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
# We use "ModemType: Class1" with "Class1Cmd: AT+FCLASS=1.0" for now
#
ModemType:              Class1          # use this to supply a hint
#ModemRate:             19200           # rate for DCE-DTE communication
#ModemFlowControl:      xonxoff         # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd:      AT&D2           # setup so DTR drop resets modem
#ModemSetupDCDCmd:      AT&C1           # setup so DCD follows carrier
#GettyArgs:             "-h %l dx_%s"   # modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machin#
#ModemDialCmd:          ATDT%s          # T for tone dialing
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:         "-SDR=6"                # stuff to do when modem is 
reset
#ModemAnswerCmd:                ATA             # use this to answer phone
#ModemNoFlowCmd:                AT&K            # disable flow control cmd
#ModemHardFlowCmd:      AT&K3           # hardware flow control cmd
#ModemSoftFlowCmd:      AT&K4           # software flow control cmd
#ModemNoAutoAnswerCmd:  ATS0=0          # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:     "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:       ATE0            # disable command echo
#ModemVerboseResultsCmd:        ATV1            # enable verbose command 
results
#ModemResultCodesCmd:   ATQ0            # enable result codes
#ModemOnHookCmd:                ATH0            # place phone on hook 
(hangup)
#ModemSoftResetCmd:     ATZ             # do soft reset of modem
#ModemSoftResetCmdDelay:        3000    # pause after soft reset
#ModemWaitTimeCmd:      ATS7=60         # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:        ATS8=2          # comma pause time is 2 
seconds
#ModemRecvFillOrder:    LSB2MSB         # bit order of received facsimile
#ModemSendFillOrder:    LSB2MSB         # bit order modem expects for 
transmit
#
Class1Cmd:              AT+FCLASS=1.0   # command to enter class 1.0
Class1PPMWaitCmd:       AT+FTS=7        # command to stop and wait before 
PPM
Class1TCFWaitCmd:       AT+FTS=7        # command to stop and wait before 
TCF
Class1EOPWaitCmd:       AT+FTS=9        # command to stop and wait before 
EOP
Class1TCFResponseDelay: 75              # 75ms delay between recv TCF & 
response
Class1SendMsgDelay:     200             # 75ms delay after training
Class1SwitchingDelay:   75              # 150ms delay in switching 
transmission direction
Class1TrainingRecovery: 1500            # 1.5sec delay after training 
failure
Class1RecvAbortOK:      200             # wait 200ms for abort response
Class1FrameOverhead:    4               # 4 byte overhead in recvd HDLC 
frames
Class1RecvIdentTimer:   40000           # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    10              # max 10% of data may be non-zero
Class1TCFMinRun:        1000            # min run is 2/3rds of TCF duration

# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@". 


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*