I have purchases a multitech ISI card modem it was recognized as
MT5634SMI-V92/1.32b. I was testing it and this is the output. I
know it's bad, but not sure what's going on here. I have listed the
configuration below as well.
Thanks ahead of time
Peter Halliday
[root@silver ~]# tail -f /etc/hylafax/log/c000000004
Jan 13 02:55:10.46: [ 4303]: <-- [23:AT+FCC=1,5,2,2,3,1,0,0\r]
Jan 13 02:55:10.58: [ 4303]: --> [2:OK]
Jan 13 02:55:10.58: [ 4303]: DIAL 7038168824
Jan 13 02:55:10.58: [ 4303]: <-- [30:AT+FCC=,,,,,,,,0;DT7038168824\r]
Jan 13 02:55:21.11: [ 4303]: --> [11:NO DIALTONE]
Jan 13 02:55:21.11: [ 4303]: SEND FAILED: JOB 4 DEST 7038168824 ERR
No local dialtone
Jan 13 02:55:21.11: [ 4303]: SEND FAILED: JOB 4 DEST 7038168824 ERR
No local dialtone; too many attempts to dial
Jan 13 02:55:21.11: [ 4303]: <-- [5:ATH0\r]
Jan 13 02:55:21.34: [ 4303]: --> [2:OK]
Jan 13 02:55:21.34: [ 4303]: SESSION END
[root@silver ~]# tail -f /etc/hylafax/log/c000000040
Feb 07 10:19:58.29: [22351]: <-- [15:AT+FNR=1,1,1,1\r]
Feb 07 10:19:58.41: [22351]: --> [2:OK]
Feb 07 10:19:58.41: [22351]: <-- [13:AT+FAP=1,1,1\r]
Feb 07 10:19:58.52: [22351]: --> [2:OK]
Feb 07 10:19:58.52: [22351]: <-- [9:AT+FIE=0\r]
Feb 07 10:19:58.63: [22351]: --> [2:OK]
Feb 07 10:19:58.63: [22351]: <-- [23:AT+FCC=1,5,2,2,3,1,0,0\r]
Feb 07 10:19:58.75: [22351]: --> [2:OK]
Feb 07 10:19:58.75: [22351]: DIAL 7038168824
Feb 07 10:19:58.75: [22351]: <-- [30:AT+FCC=,,,,,,,,0;DT7038168824\r]
Feb 07 10:20:21.11: [22351]: --> [4:+FCO]
Feb 07 10:20:21.11: [22351]: --> [46:+FNF:00 00 11 80 00 8A 48 00 FF
00 80 80 80 00]
Feb 07 10:20:21.11: [22351]: REMOTE NSF "00 00 11 80 00 8A 48 00 FF
00 80 80 80 00"
Feb 07 10:20:21.11: [22351]: NSF remote fax equipment: Canon
Feb 07 10:20:21.53: [22351]: --> [20:+FIS:1,5,0,2,7,1,0,5]
Feb 07 10:20:21.53: [22351]: --> [2:OK]
Feb 07 10:20:21.53: [22351]: REMOTE best rate 14400 bit/s
Feb 07 10:20:21.53: [22351]: REMOTE max A4 page width (215 mm)
Feb 07 10:20:21.53: [22351]: REMOTE max unlimited page length
Feb 07 10:20:21.53: [22351]: REMOTE best vres 7.7 line/mm
Feb 07 10:20:21.53: [22351]: REMOTE best format 2-D MMR
Feb 07 10:20:21.53: [22351]: REMOTE supports T.30 Annex A, 256-byte ECM
Feb 07 10:20:21.53: [22351]: REMOTE best 20 ms/scanline
Feb 07 10:20:21.53: [22351]: USE 14400 bit/s
Feb 07 10:20:21.53: [22351]: USE 20 ms/scanline
Feb 07 10:20:21.53: [22351]: SEND file "docq/doc41.ps;41"
Feb 07 10:20:21.53: [22351]: USE A4 page width (215 mm)
Feb 07 10:20:21.53: [22351]: USE unlimited page length
Feb 07 10:20:21.53: [22351]: USE 7.7 line/mm
Feb 07 10:20:21.53: [22351]: USE 2-D MR
Feb 07 10:20:21.53: [22351]: <-- [23:AT+FIS=1,5,0,2,1,0,0,5\r]
Feb 07 10:20:21.65: [22351]: --> [2:OK]
Feb 07 10:20:21.65: [22351]: <-- [7:AT+FDT\r]
Feb 07 10:21:21.63: [22351]: --> [7:+FHS:25]
Feb 07 10:21:21.87: [22351]: --> [2:OK]
Feb 07 10:21:21.87: [22351]: <-- [7:AT+FDT\r]
Feb 07 10:21:21.98: [22351]: --> [5:ERROR]
Feb 07 10:21:21.98: [22351]: <-- [7:AT+FKS\r]
Feb 07 10:21:22.10: [22351]: --> [6:+FHS:2]
Feb 07 10:21:22.10: [22351]: REMOTE HANGUP: Call aborted, from +FK
or <CAN> (code 2)
Feb 07 10:21:22.10: [22351]: MODEM Hang up
Feb 07 10:21:22.10: [22351]: SEND FAILED: JOB 41 DEST 7038168824 ERR
Communication failure during Phase B/C; too many attempts to dial
Feb 07 10:21:22.10: [22351]: <-- [5:ATH0\r]
Feb 07 10:21:22.10: [22351]: --> [2:OK]
Feb 07 10:21:22.10: [22351]: SESSION END
[root@silver ~]# cat /etc/hylafax/etc/config.ttyS49
# $Id: lucent-mt-20,v 1.13 2004/06/01 21:34:39 lhoward Exp $
#
# prototype config file for MultiTech MT5634ZBA-V.92-NAM
#
#
#
CountryCode: 1
AreaCode: 703
FAXNumber: +1.999.555.1212
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
ModemType: Class2.0
ModemRate: 19200
ModemNoFlowCmd: AT&K0
ModemSoftFlowCmd: AT&K4
ModemHardFlowCmd: AT&K3
Class2APCmd: AT+FAP=1,1,1
Class2BUGCmd: AT+FBU=0 # early firmware is
buggy
Class2SendRTC: yes
Class2UseHex: yes
# Some firmwares do not report copy quality correction, although it
# is present and cannot be disabled. Thus modem-based CQ must be used.
Class2CQQueryCmd: "!(00-02),(00-02)"
Class2CQCmd: AT+FCQ=1,0
# versions that respond to AT+FFC=? with non-zero data support RTFCC
# Class2RTFCC: yes
# unfortunately, HylaFAX can't currently send or receive in color
ModemAnswerCmd: AT+FCC=,,,,,,,,0;A
ModemDialCmd: AT+FCC=,,,,,,,,0;DT%s
# Some firmware revisions (i.e. 1.25 in ZBAs) report MMR support but
# corrupt the data. Enabling the following lines should work around
this.
# Compare this against the modem's AT+FCC=? response.
# Class2DCCQueryCmd:
"!(00-01),(00-05),(00-02),(00-02),(00-01),(00-01),(00),(00-07)"
# ModemAnswerCmd: AT+FCC=,,,,1,,,,0;A
# ModemDialCmd: AT+FCC=,,,,1,,,,0;DT%s
# If your modem supports ECM you may want to do something like this
# Class2Cmd: AT+FCLASS=2.0;+FRY=4
# If your line supports Caller-ID, you may want to uncomment this...
# QualifyCID: etc/cid # you must create this file
# ModemResetCmds: AT+VCID=1
# CIDNumber: "NMBR="
# CIDName: "NAME="
# Or with the MT5634ZBA-DID you'll probably need something like...
# ModemReadyCmds: AT*DS1*DD0*DF1*DN4 # enable DTMF-DID,
wink-start, 4 digits
# CIDNumber: "DTMF" # format of AT*DF1
# CIDNumberAnswerLength: 4 # four DTMF-DID digits then ATA
____________________ HylaFAX(tm) Users Mailing List
_______________________
To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
/dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
