|
Report any problems to
webmaster@hylafax.org
HylaFAX is a trademark of Silicon Graphics Corporation. Internet connectivity for hylafax.org is provided by: VirtuALL Private Host Services |
| Hylafax Mailing List Archives |
|
Hi
I have HylaFAX 4.2.0 running on Red Hat Linux 7.3
for recieving faxes.
This has been running ok for a few months, since a
few days i get error messages:
'Failed to properly detect high-speed data
carrier'
As far as i know nothing has changed in the
configuration
Thijs
Log file:
Jan 12 10:31:18.60: [ 3215]: SESSION BEGIN
000006018 ***********
Jan 12 10:31:18.60: [ 3215]: HylaFAX (tm) Version 4.2.0 Jan 12 10:31:18.60: [ 3215]: <-- [4:ATA\r] Jan 12 10:31:32.49: [ 3215]: --> [7:CONNECT] Jan 12 10:31:32.49: [ 3215]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS1' Jan 12 10:31:32.49: [ 3215]: RECV FAX: begin Jan 12 10:31:32.49: [ 3215]: <-- data [32] Jan 12 10:31:32.49: [ 3215]: <-- data [2] Jan 12 10:31:34.36: [ 3215]: --> [7:CONNECT] Jan 12 10:31:34.36: [ 3215]: <-- data [23] Jan 12 10:31:34.36: [ 3215]: <-- data [2] Jan 12 10:31:35.13: [ 3215]: --> [7:CONNECT] Jan 12 10:31:35.13: [ 3215]: <-- data [10] Jan 12 10:31:35.13: [ 3215]: <-- data [2] Jan 12 10:31:35.58: [ 3215]: --> [2:OK] Jan 12 10:31:35.58: [ 3215]: <-- [9:AT+FRH=3\r] Jan 12 10:31:36.00: [ 3215]: --> [7:CONNECT] Jan 12 10:31:38.04: [ 3215]: --> [2:OK] Jan 12 10:31:38.04: [ 3215]: REMOTE TSI "*************" Jan 12 10:31:38.04: [ 3215]: <-- [9:AT+FRH=3\r] Jan 12 10:31:38.06: [ 3215]: --> [7:CONNECT] Jan 12 10:31:38.08: [ 3215]: --> [2:OK] Jan 12 10:31:38.08: [ 3215]: REMOTE wants 14400 bit/s Jan 12 10:31:38.08: [ 3215]: REMOTE wants A4 page width (215 mm) Jan 12 10:31:38.08: [ 3215]: REMOTE wants unlimited page length Jan 12 10:31:38.08: [ 3215]: REMOTE wants 3.85 line/mm Jan 12 10:31:38.08: [ 3215]: REMOTE wants 2-D MMR Jan 12 10:31:38.08: [ 3215]: REMOTE wants T.30 Annex A, 256-byte ECM Jan 12 10:31:38.08: [ 3215]: RECV training at v.17 14400 bit/s Jan 12 10:31:38.08: [ 3215]: <-- [11:AT+FRM=145\r] Jan 12 10:31:39.51: [ 3215]: --> [7:CONNECT] Jan 12 10:31:41.14: [ 3215]: RECV: TCF 2935 bytes, 7% non-zero, 1586 zero-run Jan 12 10:31:41.14: [ 3215]: RECV: reject TCF (zero run too short, min 1800) Jan 12 10:31:41.14: [ 3215]: --> [10:NO CARRIER] Jan 12 10:31:41.14: [ 3215]: DELAY 75 ms Jan 12 10:31:41.22: [ 3215]: <-- [9:AT+FTH=3\r] Jan 12 10:31:41.28: [ 3215]: --> [7:CONNECT] Jan 12 10:31:41.28: [ 3215]: <-- data [3] Jan 12 10:31:41.28: [ 3215]: <-- data [2] Jan 12 10:31:42.42: [ 3215]: --> [2:OK] Jan 12 10:31:42.42: [ 3215]: TRAINING failed Jan 12 10:31:42.42: [ 3215]: <-- [9:AT+FRH=3\r] Jan 12 10:31:42.83: [ 3215]: --> [7:CONNECT] Jan 12 10:31:44.89: [ 3215]: --> [2:OK] Jan 12 10:31:44.89: [ 3215]: REMOTE TSI "*************" Jan 12 10:31:44.89: [ 3215]: <-- [9:AT+FRH=3\r] Jan 12 10:31:44.91: [ 3215]: --> [7:CONNECT] Jan 12 10:31:44.93: [ 3215]: --> [2:OK] Jan 12 10:31:44.93: [ 3215]: REMOTE wants 12000 bit/s Jan 12 10:31:44.93: [ 3215]: REMOTE wants A4 page width (215 mm) Jan 12 10:31:44.93: [ 3215]: REMOTE wants unlimited page length Jan 12 10:31:44.93: [ 3215]: REMOTE wants 3.85 line/mm Jan 12 10:31:44.93: [ 3215]: REMOTE wants 2-D MMR Jan 12 10:31:44.93: [ 3215]: REMOTE wants T.30 Annex A, 256-byte ECM Jan 12 10:31:44.93: [ 3215]: RECV training at v.17 12000 bit/s Jan 12 10:31:44.93: [ 3215]: <-- [11:AT+FRM=121\r] Jan 12 10:31:46.34: [ 3215]: --> [7:CONNECT] Jan 12 10:31:47.98: [ 3215]: RECV: TCF 2451 bytes, 7% non-zero, 1545 zero-run Jan 12 10:31:47.98: [ 3215]: --> [10:NO CARRIER] Jan 12 10:31:47.98: [ 3215]: DELAY 75 ms Jan 12 10:31:48.06: [ 3215]: TRAINING succeeded Jan 12 10:31:48.06: [ 3215]: <-- [9:AT+FTH=3\r] Jan 12 10:31:48.12: [ 3215]: --> [7:CONNECT] Jan 12 10:31:48.12: [ 3215]: <-- data [3] Jan 12 10:31:48.12: [ 3215]: <-- data [2] Jan 12 10:31:49.33: [ 3215]: --> [2:OK] Jan 12 10:31:49.33: [ 3215]: <-- [11:AT+FRM=122\r] Jan 12 10:31:50.06: [ 3215]: --> [7:CONNECT] Jan 12 10:31:50.41: [ 3215]: RECV received frame number 0 Jan 12 10:31:50.58: [ 3215]: RECV received frame number 1 Jan 12 10:31:50.76: [ 3215]: HDLC frame not byte-oriented. Trailing byte: 0xe0 Jan 12 10:31:50.94: [ 3215]: RECV received frame number 3 Jan 12 10:31:51.12: [ 3215]: RECV received frame number 4 Jan 12 10:31:51.21: [ 3215]: Bad HDLC terminating flag received. Jan 12 10:31:51.48: [ 3215]: RECV received frame number 6 Jan 12 10:31:51.66: [ 3215]: RECV received frame number 7 Jan 12 10:31:51.84: [ 3215]: RECV received frame number 8 Jan 12 10:31:52.02: [ 3215]: RECV received frame number 9 Jan 12 10:31:52.20: [ 3215]: RECV received frame number 10 Jan 12 10:31:52.38: [ 3215]: RECV received frame number 11 Jan 12 10:31:52.55: [ 3215]: RECV received frame number 12 Jan 12 10:31:52.73: [ 3215]: RECV received frame number 13 Jan 12 10:31:52.91: [ 3215]: RECV received frame number 14 Jan 12 10:31:53.08: [ 3215]: RECV received frame number 15 Jan 12 10:31:53.26: [ 3215]: RECV received frame number 16 Jan 12 10:31:53.44: [ 3215]: RECV received frame number 17 Jan 12 10:31:53.62: [ 3215]: RECV received frame number 18 Jan 12 10:31:53.62: [ 3215]: RECV frame FCS check failed Jan 12 10:31:53.80: [ 3215]: RECV received frame number 19 Jan 12 10:31:53.80: [ 3215]: RECV frame FCS check failed Jan 12 10:31:54.07: [ 3215]: RECV received frame number 20 Jan 12 10:31:54.07: [ 3215]: RECV received RCP frame Jan 12 10:31:54.07: [ 3215]: --> [10:NO CARRIER] Jan 12 10:31:54.07: [ 3215]: <-- [9:AT+FRH=3\r] Jan 12 10:31:54.27: [ 3215]: --> [7:CONNECT] Jan 12 10:31:55.43: [ 3215]: --> [2:OK] Jan 12 10:31:55.43: [ 3215]: RECV recv PPS (partial page signal) Jan 12 10:31:55.43: [ 3215]: RECV recv EOP (no more pages or documents) Jan 12 10:31:55.43: [ 3215]: RECV received 21 frames of block 1 of page 1 Jan 12 10:31:55.43: [ 3215]: <-- [9:AT+FRS=7\r] Jan 12 10:31:55.52: [ 3215]: --> [2:OK] Jan 12 10:31:55.52: [ 3215]: <-- [9:AT+FTH=3\r] Jan 12 10:31:55.54: [ 3215]: --> [7:CONNECT] Jan 12 10:31:55.54: [ 3215]: <-- data [35] Jan 12 10:31:55.54: [ 3215]: <-- data [2] Jan 12 10:31:57.72: [ 3215]: --> [2:OK] Jan 12 10:31:57.72: [ 3215]: RECV send PPR (partial page request) Jan 12 10:31:57.72: [ 3215]: <-- [11:AT+FRM=122\r] Jan 12 10:31:57.84: [ 3215]: --> [5:ERROR] Jan 12 10:31:57.84: [ 3215]: RECV keeping unconfirmed page Jan 12 10:31:57.85: [ 3215]: RECV: 5376 bytes of data, 14 total lines Jan 12 10:31:57.85: [ 3215]: RECV FAX (000006018): from *************, page 1 in 0:09, INF, 3.85 line/mm, 2-D MMR, 12000 bit/s Jan 12 10:31:57.85: [ 3215]: RECV FAX (000006018): recvq/fax000001981.tif from *************, route to <unspecified>, 1 pages in 0:25 Jan 12 10:31:57.85: [ 3215]: RECV FAX: Failed to properly detect high-speed data carrier. Jan 12 10:31:57.85: [ 3215]: <-- [9:AT+FTH=3\r] Jan 12 10:31:57.87: [ 3215]: --> [7:CONNECT] Jan 12 10:31:57.87: [ 3215]: <-- data [3] Jan 12 10:31:57.87: [ 3215]: <-- data [2] Jan 12 10:31:59.06: [ 3215]: --> [2:OK] Jan 12 10:31:59.06: [ 3215]: RECV FAX (000006018): session with ************* terminated abnormally: Failed to properly detect high-speed data carrier. Jan 12 10:31:59.06: [ 3215]: RECV FAX: bin/faxrcvd "recvq/fax000001981.tif" "ttyS1" "000006018" "Failed to properly detect high-speed data carrier." "" "" Jan 12 10:31:59.06: [ 3215]: RECV FAX: end Jan 12 10:31:59.06: [ 3215]: SESSION END File config.ttyS1:
LongDistancePrefix:
1
InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0666 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 ModemType:
Class1 # hint to override
class
2
ModemRate: 19200 # locked for fax sending ModemFlowControl: xonxoff # default ModemSetupDTRCmd:
AT&D2 # DTR off
causes modem to hangup
ModemSetupDCDCmd: AT&C0 # DCD always on ModemMfrQueryCmd:
!Nuvo
ModemModelQueryCmd: !9624PFX ModemRevQueryCmd: ATI3 ModemDialCmd:
ATDT%s # T for tone
dialing
|
|
|
|