|
Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
Re: [hylafax-users] Failure to train remote modem !?
I don't confirm that the receiver only supports 4800 baud.
The log with 0xFFF:
Nov 17 17:00:42.96: [26175]: SESSION BEGIN 000000316 **********
Nov 17 17:00:42.96: [26175]: HylaFAX (tm) Version 4.2.0
Nov 17 17:00:42.96: [26175]: SEND FAX: JOB 116 DEST ********** COMMID
000000316 DEVICE '/dev/ttyS0'
Nov 17 17:00:42.96: [26175]: STATE CHANGE: RUNNING -> SENDING
Nov 17 17:00:42.96: [26175]: sched policy=1, priority=1
Nov 17 17:00:42.96: [26175]: MODEM input buffering enabled
Nov 17 17:00:42.96: [26175]: <-- [12:AT+FCLASS=1\r]
Nov 17 17:00:43.10: [26175]: --> [2:OK]
Nov 17 17:00:43.10: [26175]: DIAL **********
Nov 17 17:00:43.10: [26175]: <-- [16:ATDT***********\r]
Nov 17 17:00:57.54: [26175]: --> [7:CONNECT]
Nov 17 17:00:57.54: [26175]: MODEM input buffering disabled
Nov 17 17:00:58.94: [26175]: --> HDLC<23:FF C0 02 8C 1C AC 1C AC AC 04 04 04
04 04 04 04 04 04 04 04 04 04 04>
Nov 17 17:00:58.94: [26175]: --> [2:OK]
Nov 17 17:00:58.94: [26175]: REMOTE CSI "******"
Nov 17 17:00:58.94: [26175]: <-- [9:AT+FRH=3\r]
Nov 17 17:00:58.98: [26175]: --> [7:CONNECT]
Nov 17 17:00:59.29: [26175]: --> HDLC<7:FF C8 01 00 52 0F 00>
Nov 17 17:00:59.29: [26175]: --> [2:OK]
Nov 17 17:00:59.29: [26175]: REMOTE best rate 4800 bit/s
Nov 17 17:00:59.29: [26175]: REMOTE max A4 page width (215 mm)
Nov 17 17:00:59.29: [26175]: REMOTE max A4 page length (297 mm)
Nov 17 17:00:59.29: [26175]: REMOTE best vres 7.7 line/mm
Nov 17 17:00:59.29: [26175]: REMOTE best format 1-D MH
Nov 17 17:00:59.29: [26175]: REMOTE best 0 ms/scanline
Nov 17 17:00:59.29: [26175]: USE 4800 bit/s
Nov 17 17:00:59.29: [26175]: USE 0 ms/scanline
Nov 17 17:00:59.29: [26175]: SEND file "docq/doc193.ps;01"
Nov 17 17:00:59.29: [26175]: USE A4 page width (215 mm)
Nov 17 17:00:59.29: [26175]: USE A4 page length (297 mm)
Nov 17 17:00:59.29: [26175]: USE 7.7 line/mm
Nov 17 17:00:59.29: [26175]: USE 1-D MH
Nov 17 17:00:59.29: [26175]: SEND training at v.27ter 4800 bit/s
Nov 17 17:00:59.29: [26175]: <-- [9:AT+FTH=3\r]
Nov 17 17:01:00.33: [26175]: --> [7:CONNECT]
Nov 17 17:01:00.33: [26175]: <-- HDLC<23:FF C0 C2 8C 6C CC 4C CC 8C 2C 8C 6C
CC D4 04 04 04 04 04 04 04 04 04>
Nov 17 17:01:00.33: [26175]: <-- data [23]
Nov 17 17:01:00.33: [26175]: <-- data [2]
Nov 17 17:01:01.34: [26175]: --> [7:CONNECT]
Nov 17 17:01:01.34: [26175]: <-- HDLC<6:FF C8 C1 00 52 0E>
Nov 17 17:01:01.34: [26175]: <-- data [6]
Nov 17 17:01:01.34: [26175]: <-- data [2]
Nov 17 17:01:01.64: [26175]: --> [2:OK]
Nov 17 17:01:01.64: [26175]: DELAY 70 ms
Nov 17 17:01:01.71: [26175]: <-- [10:AT+FTM=48\r]
Nov 17 17:01:02.73: [26175]: --> [7:CONNECT]
Nov 17 17:01:02.73: [26175]: <-- data [900]
Nov 17 17:01:02.73: [26175]: <-- data [2]
Nov 17 17:01:04.29: [26175]: --> [2:]
Nov 17 17:01:04.29: [26175]: Problem sending TCF data
Nov 17 17:01:04.29: [26175]: <-- [9:AT+FRH=3\r]
Nov 17 17:01:04.29: [26175]: --> [2:OK]
Nov 17 17:01:04.29: [26175]: DELAY 1500 ms
Nov 17 17:01:05.79: [26175]: SEND training at v.27ter fallback mode 2400
bit/s
Nov 17 17:01:05.79: [26175]: <-- [9:AT+FTH=3\r]
Nov 17 17:01:05.79: [26175]: --> [7:CONNECT]
Nov 17 17:01:05.79: [26175]: <-- HDLC<23:FF C0 C2 8C 6C CC 4C CC 8C 2C 8C 6C
CC D4 04 04 04 04 04 04 04 04 04>
Nov 17 17:01:05.79: [26175]: <-- data [23]
Nov 17 17:01:05.79: [26175]: <-- data [2]
Nov 17 17:01:05.79: [26175]: --> [5:˙"]
Nov 17 17:01:05.79: [26175]: Error sending T.30 prologue frames
Nov 17 17:01:05.79: [26175]: TRAINING failed
Nov 17 17:01:05.79: [26175]: <-- [9:AT+FTH=3\r]
Nov 17 17:01:05.79: [26175]: --> [2:OK]
Nov 17 17:01:05.79: [26175]: MODEM input buffering enabled
Nov 17 17:01:05.79: [26175]: <-- [5:ATH0\r]
Nov 17 17:01:06.93: [26175]: --> [7:CONNECT]
Nov 17 17:01:07.92: [26175]: --> [7:CONNECT]
Nov 17 17:01:12.92: [26175]: MODEM TIMEOUT: reading line from modem
Nov 17 17:01:12.92: [26175]: MODEM <Timeout>
Nov 17 17:01:12.92: [26175]: MODEM set DTR OFF
Nov 17 17:01:12.92: [26175]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Nov 17 17:01:12.92: [26175]: sched policy=0, priority=0
Nov 17 17:01:12.92: [26175]: SESSION END
Balázs
-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Lee Howard
Sent: Wednesday, November 17, 2004 4:50 PM
To: K.Balázs
Cc: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] Failure to train remote modem !?
On 2004.11.17 07:14 K.Balázs wrote:
> Hi list!
>
> I !sometimes! get the following error: Failure to train remote modem
> Nov 17 11:19:26.83: [ 4551]: REMOTE best rate 4800 bit/s
What kind of receiver is this that only supports 4800 baud? Can you
confirm that the receiver only supports 4800 baud?
Could you provide a send session log with SessionTracing: 0xFFF ?
Lee.
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
